Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

FWW / Epic Woodworking Shaker Chest of Drawers

Featured Replies

On 7/19/2021 at 3:41 PM, mdbuilder said:

Yes, MD Select is my normal guy. I've occasionally gotten a grade B board when I come across it in the pile, depending on the size of parts you need they can be OK. Generally more knots so you are not going to get a 5 or 6 foot part out of it. Also, not sure how much B stuff he regularly stocks. You might want to call first and ask how much B grade he has for whatever species you are looking for. He is on the net: https://www.maryland-select.com/

Thanks for the insight, it was exactly what I was looking for. Not sure if I'll make it out there for this round. Too much going on to spend 2-3 extra hours in the car if I can avoid it at the moment. 

  • Replies 149
  • Views 29.7k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Project left the shop today, wrapped it in moving blankets, loaded on a hand truck and up 2 flights of stairs it went with a bit of wifely assistance. Few more trips up and down with drawers, int

  • After hours of sanding, first coat of oil is on. 

  • External work is all done. Tonight I rubbed it all out with wax and steel wool. Also permanently installed all the knobs, went with glue and a single screw for each knob from the back. Top is also scr

Posted Images

  • Author

Sorry, one more pic now that all three partitions and rear rails are planed. Just love the way the light glints.

PXL_20210720_000854636.jpg

Just a curiosity question. I see on your dust partitions, the frame is proud of the panels and that you said you planed the panels from 4/4 to 1/2”. Is the reason you didn’t make the panels the same thickness as the frame due to cutting a little weight from the project. If it were me, I probably would have done the same, but only to keep from trying to make them flush. ;)

  • Author
On 7/19/2021 at 10:27 PM, Coop said:

Just a curiosity question. I see on your dust partitions, the frame is proud of the panels and that you said you planed the panels from 4/4 to 1/2”. Is the reason you didn’t make the panels the same thickness as the frame due to cutting a little weight from the project. If it were me, I probably would have done the same, but only to keep from trying to make them flush. ;)

Well, the simple answer is the plan calls for a half inch so I followed what the designer called for :D.

 

On the other hand, your observation about weight is good. The partitions are purely cosmetic rather than structural so lighter is good. Also, you want the drawers to slide easily and touch only on the drawer sides sliding on the runners. If the partitions were full thickness the back of the drawer and bottom would  potentially make contact?

On 7/20/2021 at 2:46 AM, mdbuilder said:

the plan calls for a half inch so I followed what the designer called for

Good answer.

Dust frames and panels are traditionally made like frame and panel doors, where the panel is recessed in the frame.  Originally they were used to keep dust from settling on what ever is in the drawer below.

  • Author

LOL, upon further study the designer actually calls for 5/16+ on both the drawer bottoms AND the dust partitions. I think I'll leave the latter as is an try a little re-sawing when I get the the drawer bottoms. 

  • Author
  • Popular Post

Starting on the back which are a 6 & 5/8 wide ship lapped arrangement.

PXL_20210721_023854097.jpg

PXL_20210721_023911691.jpg

  • Author

I think I will take those 2 darker boards and alternate them with the lighter boards. Opinions? 

On 7/21/2021 at 7:42 AM, mdbuilder said:

I think I will take those 2 darker boards and alternate them with the lighter boards. Opinions? 

I would probably do something like that.  Also on some shaker pieces you will see were the back panels are finished with something like white or gray milk paint.  In the end it is in an area that isn't really seen once the piece is in place.

Has it already been stated and I missed it? What kind of finish will you be using? 

  • Author

The inside of the case and everything on the drawers except the front face get 2 coats on 1.5 pound cut shellac. The outside gets 3 coats of natural Danish oil and 2 coats of Waterlox.

  • Author
  • Popular Post
On 7/21/2021 at 11:19 PM, Coop said:

Looking forward to the finish! 

That may be a while:P, guessing at least a month to finish construction. 80 or so dovetails in the drawers...

Slowly working my way across the back, drill the countersink for the screws, drill the bigger clearance for the shank, cleanup the faces with the #4, pop in a couple of shims to set the spacing and drill the 2 holes top and bottom. Then of course you need to run in a steel screw with the impact driver, back it out and replace with the brass screw:D

PXL_20210722_094526470.jpg

PXL_20210722_094540201.jpg

  • Author
  • Popular Post

This thing is getting heavy!

 

After wrestling it to the floor I cleaned up the sides with a #5 set very fine. I wiped them down with some paint thinner to get an idea what it will look like. Not too shabby I think.PXL_20210723_110328996.thumb.jpg.e6ff7e4728b47a5ab6ff3f521b30b6a9.jpg

PXL_20210723_111224499.jpg

PXL_20210723_111253234.jpg

  • Author

Glue up for the top, 21"*40" is the target size. I've got about 5/8 of extra length:rolleyes:, we'll see how this works out. Would not normally cut is so close but the plank the 3 pieces came from was 122'ish inches long.

PXL_20210725_002109434.jpg

  • Author
  • Popular Post

The top is done, I had a bit of a drum sander incident. When you hear a tic-tic sound evidently it is a sign your paper is about wore out :rolleyes:. When it did wear out I wound up with a pretty significant burnt gouge on one side of the top. Anyway, changed to 120 grit and sanded a bit further than I was planning to to remove the damage. The top is now .71 inches instead of .75. Gentle rounding off still to come...

Also glued the stock for the cove to a carrier board to make the routing a little safer and sanded to 5/8 thick. This molding will make the transition from the base to the case.

PXL_20210725_180512991.jpg

PXL_20210725_180634987.jpg

  • Author
  • Popular Post

Tool recommendation of the day. At the beginning of this project I picked up 2 new sawblades from Ridge Carbide. One was a flat top blade ground for a dovetail angle, nice but what can you say?

The other is their 10" 48 tooth TS2000 Ultra Combo blade. WOW, this thing really cuts cleanly. The 21" crosscuts on the top panel was flawless. It'll also cut plywood with zero chip out on the bottom and the cut is polished.

Anyway, just thought I'd pass that along. Expensive but they really perform.

  • Author

Grrrr! I made an error, cut the side pieces for the base 3/4" short :blink:. The front and back are perfect, Unless someone has a method to make the sides longer they will be going on the firewood pile...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.