Woodworking_Hobby Posted April 5, 2025 Report Posted April 5, 2025 I have a project in the works that has some drawer fronts that are 8, 11, and 12 inches wide. My jointer is only six inches and I really don’t want to take the time make a bunch of glue up panels for the fronts. Is it really as easy as making a planer sled that is wider and longer than my parts? Can I just use MDF for the sled? Any recommended thickness? Can I just use what they sell at HD or Lowe’s from a quality standpoint? Can I hold the rough lumber with double stick tape or does it really need hot glued? Anything else to be aware of if I go down this path and not starting the milling operation with my jointer as normal? 1 Quote
Popular Post gee-dub Posted April 5, 2025 Popular Post Report Posted April 5, 2025 My "Keith Rust" planer sled took about 4 hours to make not counting waiting overnight for the glue to set. FWW planer sled.pdf By the way, I didn’t use laminate on the underside. I just shellacked it and waxed it and it’s been fine for I don’t even know how many years. There is a much nicer one from ShopNotes magazine but mine has done well all these years. Planer Sled SN 137.pdf 3 2 Quote
wtnhighlander Posted April 5, 2025 Report Posted April 5, 2025 A piece of mdf works great as a planer sled. It just needs to provide a flat surface opposite the cutters. As for fastening the work, any method that holds it rigidly in place can work. It just needs to hold firmly against the work piece rocking on tbe sled. 1 1 Quote
Beechwood Chip Posted April 5, 2025 Report Posted April 5, 2025 I'm thinking a 14" piece of MDF with some MatchFit slots in one side is a: planer sled with some low profile stops at one end table saw tapering/jointing sled with some MatchFit clamps to hold the piece, and maybe some stops for repeatability table saw tall auxiliary fence with MatchFit clamps to clamp onto the fence table saw sacrificial fence with MatchFit clamps to clamp onto the fence 1 1 Quote
Woodworking_Hobby Posted April 6, 2025 Author Report Posted April 6, 2025 14 hours ago, gee-dub said: My "Keith Rust" planer sled took about 4 hours to make not counting waiting overnight for the glue to set. FWW planer sled.pdf 1.11 MB · 4 downloads By the way, I didn’t use laminate on the underside. I just shellacked it and waxed it and it’s been fine for I don’t even know how many years. There is a much nicer one from ShopNotes magazine but mine has done well all these years. Planer Sled SN 137.pdf 5.89 MB · 3 downloads That sled from FWW looks great and might have to add that to the list. I am guessing this is more self leveling so you do not have to mess with the glue or other ways to hold the board flat on just MDF. I agree with your comment on the Shop Notes sled. It is nice but I think I would have to buy a bunch of tools just to make the sled. TBH sometimes that’s why I shy away from these as they seem more complicated to build than what I am trying to make. Is that quartersawn Sapele you are milling? Looks like you are making some that will be great! Quote
Popular Post gee-dub Posted April 6, 2025 Popular Post Report Posted April 6, 2025 On 4/6/2025 at 6:14 AM, Woodworking_Hobby said: That sled from FWW looks great and might have to add that to the list. I am guessing this is more self leveling so you do not have to mess with the glue or other ways to hold the board flat on just MDF. I agree with your comment on the Shop Notes sled. It is nice but I think I would have to buy a bunch of tools just to make the sled. TBH sometimes that’s why I shy away from these as they seem more complicated to build than what I am trying to make. Is that quartersawn Sapele you are milling? Looks like you are making some that will be great! Correct, the sled has little wedges and simple wood screws as "keepers". It is very easy to set the material on the crossbars and raise them till they contact the material. Slide the wedge and finger-tighten the screw to keep it in place. I used stair tread grip since it had an adhesive backing and I had it on hand but any coarse abrasive would work. That is Sapele and is from the current headboard project that is taking longer than anything I have ever done . Life just gets in the way sometimes. 3 Quote
Von Posted April 6, 2025 Report Posted April 6, 2025 Yes, a jig is on my to-do list, but until then I'm making do with a piece of plywood, double-stick tape, and wedges. Basically if you get get your workpiece so it doesn't rock or slide and is relatively flat, you're good to go. I don't think thickness matters too much as long as it's not flopping around. Quote
Mark J Posted April 6, 2025 Report Posted April 6, 2025 15 hours ago, gee-dub said: My "Keith Rust" planer sled took about 4 hours to make not counting waiting overnight for the glue to set. FWW planer sled.pdf 1.11 MB · 5 downloads By the way, I didn’t use laminate on the underside. I just shellacked it and waxed it and it’s been fine for I don’t even know how many years. There is a much nicer one from ShopNotes magazine but mine has done well all these years. Planer Sled SN 137.pdf 5.89 MB · 4 downloads I can't open or download either of the PDF's. Any idea what I'm doing wrong? Quote
drzaius Posted April 6, 2025 Report Posted April 6, 2025 6 minutes ago, Mark J said: I can't open or download either of the PDF's. Any idea what I'm doing wrong? Worked for me. 1 Quote
gee-dub Posted April 6, 2025 Report Posted April 6, 2025 Yeah, just worked for me too. Do you have some sort of PDF reader installed? Some ad-blockers will block downloads from sites not explicitly permitted . . . just a first guess. Quote
gee-dub Posted April 6, 2025 Report Posted April 6, 2025 On 4/6/2025 at 6:48 AM, Von said: Yes, a jig is on my to-do list, but until then I'm making do with a piece of plywood, double-stick tape, and wedges. Basically if you get get your workpiece so it doesn't rock or slide and is relatively flat, you're good to go. I don't think thickness matters too much as long as it's not flopping around. I can almost guarantee you that the amount of time you spend futzing around with hot glue and wedges is more than it takes to make the "Rust" sled. You do need to have a long enough bungee and some screw-hooks laying around . I just went to check and I made mine in 2007 for one project. I have used it ever since. Talk about a ROI. I don't mean to seem over-enthusiastic. We just all tend to recommend those things that have worked out for us. 2 Quote
Mark J Posted April 6, 2025 Report Posted April 6, 2025 2 hours ago, gee-dub said: Yeah, just worked for me too. Do you have some sort of PDF reader installed? Some ad-blockers will block downloads from sites not explicitly permitted . . . just a first guess. Tried a different computer and it worked. 2 Quote
roughsawn Posted April 26, 2025 Report Posted April 26, 2025 Kinda late to this thread, hobby. I use melamine, only 1/8" narrower than my planers. 13" DeWalt, and 20" Grizzly. I have cut and use wood shims to level, then hot melt glue the shims and slab. I recently had to take 3/4" of twist out of a bunch of big slabs. My melamine sleds work great, and it is easy to remove the glue with a chisel. I make them 4', 6', and 8' long, and use them accordingly. 1 1 Quote
Beechwood Chip Posted April 26, 2025 Report Posted April 26, 2025 On 4/25/2025 at 9:43 PM, roughsawn said: I use melamine [...] Are you using 1" melamine / particle board shelving or something else? Do you find it's stiff enough to give a flat surface over 8'? Quote
roughsawn Posted April 26, 2025 Report Posted April 26, 2025 3/4" cabinet melamine. I use the 8'er on the 20" Grizzly. It has a five foot bed, and I use extra support with roller jack stands at both infeed and outfeed. It's plenty stiff. 1 Quote
Mark J Posted April 26, 2025 Report Posted April 26, 2025 11 hours ago, roughsawn said: it is easy to remove the glue with a chisel. I've heard that hot melt glue will also come off with alcohol, but I haven't tried it. 1 Quote
Popular Post drzaius Posted April 26, 2025 Popular Post Report Posted April 26, 2025 1 hour ago, Mark J said: I've heard that hot melt glue will also come off with alcohol, but I haven't tried it. Mineral spirits readily dissolve it as well. 1 2 Quote
Woodworking_Hobby Posted September 12, 2025 Author Report Posted September 12, 2025 So I tried my hand at using a “sled” with the planer this past weekend. I had some boards that were just too messy to work with my joiner. With the long length, cup, and rocking diagonally across the boards I was just worried I would fight them the entire way on the jointer. I had some 3/4” MDF that was longer and a few inches wider than the rough boards that I used for the base. I hot glued the board to the MDF and supported with shims along its entire length. I also hot glued the shims to the board and MFD. It seemed to work ok but definitely did not produce a flat board. When I put whiteness marks across its face the jointer got to a place where it removed them all in one pass and it “looked flat” but when I removed the board from the MDF and flipped it to the milled face, it still had a slight rock from edge to edge and corner to corner. It was small enough that I was able to move to the jointer and remove the rock to get flat and then finish the milling process as normal at planer. I was just wondering since there boards are so long and heavy can the MDF still twist and flex so the sled does not work 100%? Is the sled concept going to work better if I am trying to flatten something like 4/4 cherry that is only 12 or 18 inches long and wide for a drawer face or panel that will not fit on my 6 inch jointer? I know the sleads can be made more like a true jig, this was just my solution to get a few boards done with what I had on hand in the time I had in the shop that day. 2 Quote
Popular Post Von Posted September 12, 2025 Popular Post Report Posted September 12, 2025 Your approach has worked for me, but I've never tried it on a board as long and thick as what you show. At that length (significantly longer than the planer bed), the planer can only make the two faces parallel, it can't deal with long twists down the length since the board will twist as it goes through. As you speculate, the MDF is probably conforming to the board since the board looks much sturdier than the MDF. I would be reaching for my scrub plane at this point to knock down the high points. Going back to your joiner would also seem to be an option. 3 1 Quote
Ron Swanson Jr. Posted September 12, 2025 Report Posted September 12, 2025 On 9/12/2025 at 7:35 AM, Woodworking_Hobby said: So I tried my hand at using a “sled” with the planer this past weekend. I had some boards that were just too messy to work with my joiner. With the long length, cup, and rocking diagonally across the boards I was just worried I would fight them the entire way on the jointer. I had some 3/4” MDF that was longer and a few inches wider than the rough boards that I used for the base. I hot glued the board to the MDF and supported with shims along its entire length. I also hot glued the shims to the board and MFD. It seemed to work ok but definitely did not produce a flat board. When I put whiteness marks across its face the jointer got to a place where it removed them all in one pass and it “looked flat” but when I removed the board from the MDF and flipped it to the milled face, it still had a slight rock from edge to edge and corner to corner. It was small enough that I was able to move to the jointer and remove the rock to get flat and then finish the milling process as normal at planer. I was just wondering since there boards are so long and heavy can the MDF still twist and flex so the sled does not work 100%? Is the sled concept going to work better if I am trying to flatten something like 4/4 cherry that is only 12 or 18 inches long and wide for a drawer face or panel that will not fit on my 6 inch jointer? I know the sleads can be made more like a true jig, this was just my solution to get a few boards done with what I had on hand in the time I had in the shop that day. That's exactly how i plane. I plane everything on a sled that's just a piece of MDF, using carpet tape to adhere my workpiece. The longer a board is, the harder it is to get it dead flat in my experience. I doubt that your 3/4" MDF flexed. The sled will help, but the planer really isn't going to perfectly remove twist. Usually you'll just end up with a thinner twisted board. That's where the jointer shines, but removing twist on the jointer requires some technique too. Not sure how to describe this, but i split the difference on the twist by pushing the front high corner halfways down to the infeed table and running it through that way. I hope that makes sense. I think you'd probably have been better off flattenig on the jointer first, with the help of a couple roller stands and ideally, an extra set of hands. Or by using a hand plane or electric hand planer to reduce your high corners before planing. 1 1 Quote
wtnhighlander Posted September 12, 2025 Report Posted September 12, 2025 Theoretically The planer head mills stock from only a small area directly above the center of the bed. The MDF provides a flat reference against the bed, and the cutter removes material parallel to that. To ensure the entire face is milled in a single plane, the sled & workpiece assembly must be rigid and well supported, so that the upper face of the work does not twist or rock, relative to the planer bed. A single thickness of MDF may not be rigid enough for such a long workpiece, unless it is fully supported along its length. And the work can not move on the sled, or all bets are off. 1 Quote
Woodworking_Hobby Posted September 12, 2025 Author Report Posted September 12, 2025 Thanks for the suggestions! I thought this might be a little tough for the setup but gave it a try. I had the MDF and just thought I would see how the concept works and will definitely use it again in the right situations. I did not really think about using the hand plane first to know out some of the high points and for the next board going to try that and jointer to see how that changes the process. 2 Quote
Popular Post gee-dub Posted September 12, 2025 Popular Post Report Posted September 12, 2025 I know I keep pushing this agenda but the 4 hours you will spend making a decent adjustable planer sled will pay you back for years and years. Do as you will. I have the original plans if you would like them. 5 Quote
Ron Swanson Jr. Posted September 12, 2025 Report Posted September 12, 2025 @gee-dub i would love that plan! Quote
Mark J Posted September 12, 2025 Report Posted September 12, 2025 Interesting, I just realized the sled is a torsion box. I think that would be stiffer than MDF. @gee-dub, just for my curiosity, the bungees cord ends look like they wrap around and secure on the bottom side of the sled. If that's true, how does the sled sit flat on the planer bed? 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.