Popular Post Tom King Posted August 10, 2025 Popular Post Report Posted August 10, 2025 I heard a bearing in something squealing, but thought I could finish what I was working on. Bearing in the water pump had failed. The fan, which I found out was the wrong one that had been on it since I bought it used in 1991, hit the radiator ruining the radiator and fan. The hydraulic pump has been leaking for a long time, letting the bucket bleed down, but I had gotten used to it and made out. I knew the hydraulic pump needed to be changed, but you have to take the radiator, hydraulic reservoir, air filter assembly, and a few other things out to get to it. Pam said why don't you just buy a new tractor instead of keep working on that old one. I went to build and price at John Deere online. It would be nice to have one a little larger, which is the 90 hp model. 4-wheel drive would be good too. Might as well get a cab with heat and air and three remotes on the back as well as another hydraulic circuit on the front for a 4-n-1 bucket and other things. That totaled up to a bit over a hundred grand. It would be nice, but I really only use this tractor about 40 hours a year now. I really hadn't done anything to this tractor since 2021, so I'll just fix this one one more time. All the parts for this repair including a rebuilt hydraulic pump and all new hoses came to right at $1500 including an aftermarket radiator which was $262 instead of the $1351 authentic John Deere one that was probably made in China in the same factory that made the aftermarket one. The used fan in perfect condition was 50 bucks off ebay instead of the made in China "real" John Deere one for $341, The company I found online for the rebuilt hydraulic pumps only rebuilds John Deere hydraulic pumps and was $905 by the time I paid for the return label to ship the old one back, which was less than a third of a new John Deere one. The engine lift/shop crane paid off once more and I was able to get the old pump, that weighs about 75 pounds, out without any damage to fingers. I didn't put it in the shop where it would be easier to work on it because I knew it would make a mess under it with all the pressure washing and losing some hydraulic fluid. I did cut the grass real short where I parked it and sprayed it good for insects before I drove it spraying antifreeze to right in front of the shop. It was worth tearing it down just to be able to clean it all inside all the crevices in that front part of the engine. I spent way more time pressure washing it that I did tearing it down. Tractors are easy to work on if you have plenty of tools and if they're clean it's not a bad job at all. The new pump came Friday, so I pulled the old one out yesterday and should get the new one back in today. Still waiting on one radiator hose to get here, so I should finish it in a couple of days only working on it early in the mornings. 8 Quote
wtnhighlander Posted August 10, 2025 Report Posted August 10, 2025 I can't speak to the situation today, but in the early 1980s, the engines (and many other parts) of JD's compact tractor lines came from Japan, Yanmar specifically. The green paint still raised the price, by a significant margin! 1 Quote
Tom King Posted August 10, 2025 Author Report Posted August 10, 2025 The last couple of parts boxes I got from the dealer (several years ago) said "Genuine John Deere Parts". Then somewhere along the bottom: Made in China. This morning I took off the fittings from the old pump to put them on the new one, expecting to put the pump back in. Although the O-rings still looked okay I decided to order all new ones. Such is the way this type of job goes. I don't mind waiting a few more days to have all the seals new. There is no deadline on getting it back together. I just want it to be right and worry free once it is. This one does have a 1979 John Deere motor in it. I had the dealer rebuild the motor in something like 2008 and the motor is still in fine shape. When I was pricing the new 90 hp tractors, there was a choice between the E line and the M line. The E line did have a John Deere (not sure where they're made) motor and the higher priced M line had a fancier motor made somewhere else. The hundred grand one I priced had the cheaper motor in it. 2 Quote
Popular Post Tom King Posted August 12, 2025 Author Popular Post Report Posted August 12, 2025 The shop manual shows every step of every operation in great detail with pictures. An aftermarket replacement water pump costs mid $300's plus shipping. The rebuild kit includes a new impeller, shaft with built on bearings, and seals for $77.92 and I bought enough stuff in that order to get free shipping. 20 minutes with the shop press, mostly finding stuff to get everything to the right level in the range of the hydraulic jack on the press, and I'm ready to put the new parts in as soon as they arrive. The old seal was gone and the bearings were FUBAR. It had been replaced by someone else before I bought this tractor 34 years ago when it was 12 years old. 3 Quote
Popular Post Tom King Posted August 15, 2025 Author Popular Post Report Posted August 15, 2025 Parts are trickling in, but not like ordering from the billionaire. Also not enough of anything to be able to start putting parts back in. In order to get the beach dressed up for the next rental with my tractor down, I rented a Bobcat T595 CTL. Dressing up the erosion on the beach from the 6" deluge we had earlier in the week went quickly, but the almost 8,000 pound CTL had to roll the big stump up the hill and then push it over behind some trees out of sight from the house. If I can catch someone close enough with equipment and can get those stumps moved the 200 yards to my dumping spot for a couple of hundred dollars I'll get it done. Otherwise, I'll let them dry out for a year or so which will drop half their weight, cut the butt stubs off, and be able to move them with the tractor even if I have to slide them. I slid the two smaller ones with the tractor. 4 Quote
Popular Post Tom King Posted August 16, 2025 Author Popular Post Report Posted August 16, 2025 These jobs often require buying special tools. One of the big high pressure outlets on the pump is a right angle fitting that attaches to a 3/4" hard line with a big flare nut. You don't tighten that fitting until after the line is attached to it. Then a packing nuts pushes a seal down into a seat to hold the high pressure fluid inside the system. There is not enough room, on purpose I'm sure, to get a regular wrench on the packing nut or even a big pair of Channellocks. It requires a 1-7/8" Service Wrench. A service wrench is a thin one intentionally having a short handle so you can't easily over torque it. Fortunately it only cost $23 with free shipping. 3 1 Quote
BillyJack Posted August 16, 2025 Report Posted August 16, 2025 I spend a lot of time watching heavy equipment repair. One of tye things I learned about tractor repair is even thou you may have the manual, it may be one of three things.. Quote
Popular Post Tom King Posted August 19, 2025 Author Popular Post Report Posted August 19, 2025 I had to look back at this thread to see when I started this job. It seems like it's been more than 10 days, but I see it hasn't. Still waiting on a couple of parts, and they would be two that would not let me put either the hydraulic pump or the water pump back on, so I've done nothing at all about reassembling the tractor. I do have all the other parts put back where they go on the pump except that one that uses the special washer and have painted what I can. Waiting on one special washer with built in seal for one of the big pressure fittings on the hydraulic pump and one gasket to replace one that came screwed up in the water pump rebuild kit. Edited to add: Later found out that the pump kit was the wrong one-should have checked earlier. Fortunately, the beach is still in fine shape after the guests left today, and hopefully we won't have any more washing rains until I get the tractor back together. I think I can get it all back together in less than a couple of hours whenever all the parts come. At least when either one comes I can get something put back together. 4 Quote
Tom King Posted August 21, 2025 Author Report Posted August 21, 2025 Went to put the water pump rebuild kit back in today and it was the wrong one. I should have checked closer, but when I opened the package earlier and saw the torn gasket I didn't want to cut any of the packaged parts open. I checked online and no one had the right kit in stock. Called JD and they could have one tomorrow but it's 35 minutes one way and cost more than a rebuilt pump online costs that will be here Saturday. Maybe I can get that back on there this weekend if it does come Saturday. 2 1 Quote
legenddc Posted August 22, 2025 Report Posted August 22, 2025 That's great you're able to find parts and repair it yourself. For a while John Deere was forcing owners to get them repaired at a JD shop. The tractor wouldn't work if you repaired it without OEM parts. I can't recall if the lawsuit was settled ever. 1 Quote
Popular Post Tom King Posted August 22, 2025 Author Popular Post Report Posted August 22, 2025 This is a 1979 tractor made well before there were any computers in them. There is a very big aftermarket supply, just with slow shipping. There are still parts available for tractors much older than this one. It's really simple to work on. I just wish the parts would hurry up and get here. I've been spoiled by quick deliveries by the billionaire. 4 Quote
Popular Post Tom King Posted August 23, 2025 Author Popular Post Report Posted August 23, 2025 Still waiting on parts, but put some time in this morning cleaning and painting the parts to go back on. I'm just using Krylon spray cans. Spray paint is a lot better than it used to be. The 12v Milwaukee buffer is a handy little thing. For this job I'm using 2" "conditioning discs". They're really easy to change. I'm also using that to clean up all the surfaces where gaskets go, but will wait to do that just before putting stuff back together. Some of the discs are course enough to quickly smooth cast iron texture and some fine enough to put a high polish on bare metal. They quickly remove old paint from metal too. https://www.amazon.com/SATC-Sanding-Abrasive-Surface-Conditioning/dp/B07X54YXXM/ref=sr_1_3? This is the thermostat housing and hydraulic oil return line. The parts don't go together, but I hand held the line to spray it all around and its hose fit into the hose that goes to the water pump under the thermostat housing, so it was a good place to stick it for drying. 4 Quote
Popular Post Tom King Posted August 26, 2025 Author Popular Post Report Posted August 26, 2025 The part came today that has been holding up getting the hydraulic pump back in, which is holding up everything else above it. It's a special washer with a built in seal for one of the big ports on the hydraulic pump. I could have gotten it next day if I had ordered it from the dealer, but didn't want to spend over an hour driving just for this. 4 Quote
Popular Post Tom King Posted August 29, 2025 Author Popular Post Report Posted August 29, 2025 I said earlier it should take me a couple of hours to get it put back together. I should have said a couple of hours every morning over several days. Being out in front of the shop and having to walk back and forth for tools takes a lot more time than being inside where all the tools are. It was a slow fiddly job to get the heavy hydraulic pump in place with do danger to fingers but it's in there now. The Sun caught me where it is by 9:30 so the next step will have to wait for another day. The air is really pleasant today, but I'm not working in the Sun if I don't have to. The service wrench allows the big elbow on one of the high pressure lines to only be fixed in position after the flare nut is tightened to it. Everything about it is a tight fit including getting the pump where it goes. I'm glad this part if behind me. 6 Quote
Popular Post Tom King Posted August 30, 2025 Author Popular Post Report Posted August 30, 2025 The one step per day is working out nicely. This morning I installed the water pump, hydraulic pump drive, and alternator belt. After it was all installed and cleaned bolt heads and missed spots were painted. I wouldn't have wanted to do that painting to bump into getting the next parts on. The hardest parts are done. I forgot to take any pictures though. I think I'm going to take another couple of mornings to get it all back together. I feel good about everything going back on so far. 3 Quote
Ron Swanson Jr. Posted August 30, 2025 Report Posted August 30, 2025 I admire your discipline in being able to do it a bit at a time like that. I have a hard time pulling myself away once I'm into something like that. 2 Quote
Popular Post Tom King Posted August 30, 2025 Author Popular Post Report Posted August 30, 2025 I'm 75 and have been working for myself for 51 years now. I learned not to push myself years ago. My Dad used to come by one of my jobsites building a new house and would say I was being ridiculously meticulous. Many others would say they didn't know how one person could do everything and get a house built as quickly as I did. I make no claims to be fast, but I don't waste time and it's going to be right when I finish with it. By the way, the pencils are still on the dashboard of my truck. I keep getting sidetracked going the opposite direction from the Post Office. I hope to get them in the mail on Monday. 5 Quote
Ron Swanson Jr. Posted August 30, 2025 Report Posted August 30, 2025 Sounds good, Tom, no rush!! 1 Quote
Popular Post wtnhighlander Posted August 30, 2025 Popular Post Report Posted August 30, 2025 Tom, I've always heard it's faster to do it right than do it over. Someone must have been timing you! 3 Quote
Tom King Posted August 31, 2025 Author Report Posted August 31, 2025 Here's the picture I forgot to take of yesterday morning's work. I didn't paint the fan because I wouldn't expect it to stay on long anyway. It should smell better being clean and be a lot quieter with the rubber bushings in the hydraulic pump coupler. I've owned this tractor for 34 years and never remember changing that fan belt. You have to take the hydraulic pump drive coupler off to change the belt. Since I had never changed the belt I never noticed those rubber bushings weren't in there. The tractor was run hard when I bought it used at 12 years old. 2 Quote
Popular Post Tom King Posted August 31, 2025 Author Popular Post Report Posted August 31, 2025 Progress has really slowed down now. I'm having to make the correct length bolts and cut hoses that were too long, etc. from a half-assed repair decades ago. When I bought the tractor the hood was out of kilter and nothing really fit like it should. The radiator had been changed, so now I'm thinking someone bumped into something bending the front end stuff towards the back. This also explains why the fan went in the radiator from a little slop in the water pump bearing. Putting the radiator back in place, it won't go upright enough. The hydraulic reservoir and air filter assembly are mounted onto the back of the fuel tank. They don't leave enough room to get the radiator in correctly. The front end sheet metal attaches to the fuel tank too. So the fuel tank holds all that stuff plus the radiator in the correct orientation. When I slid the new radiator in, the fan just barely clears it at the top but has plenty of clearance at the bottom. I didn't put the hood back on the last time I worked on it both because it didn't fit and to try to stop all the leaks. I got all the leaks stopped but never got around to putting the hood back on. A framing square sitting on the tractor frame shows how much the radiator needs to go towards the front. Tomorrow, I'm going to hook a come-a-long to the tank and try to get things back where they go. Hopefully it won't tear the tank, but I'm determined to get it right now even if I have to buy a new fuel tank. I'll use the hood to judge exactly where to stop the bending. The tank is about half full of fuel, so if it doesn't start leaking it should be okay. At least all the proper sized bolts and washers are in now, as well as all the too long stuffed in hose lengths corrected. I'm anxious to see how quiet it is compared to how it used to be. There were a Lot of things to rattle up there. 5 Quote
Tpt life Posted August 31, 2025 Report Posted August 31, 2025 Any buddies with a frame stretcher? If not, with mature trees and some come-alongs, thin stuff can be coaxed back. Thick stuff seems easier to cut and weld. Quote
Tom King Posted August 31, 2025 Author Report Posted August 31, 2025 I'll figure it out tomorrow when I get my eyes and hands on it. I'm not going to worry about it today. Hopefully a way will present itself to move the tank without having to do any bending. 1 Quote
Popular Post Tom King Posted August 31, 2025 Author Popular Post Report Posted August 31, 2025 I needed to get something out of the shop so I took these pictures. Looks like the fuel tank that holds everything else is just bolted to the front sheet metal piece. There is evidence of it being bent a long time ago. All the fasteners are easy to get to. It should be easy to figure it out in the morning. I looked it up online in the very nicely displayed John Deere parts exploded diagram and the tank just bolts to the front thing called the "front plate". I found the part number and a used one online for $259 plus $32 shipping, but I don't think it will be bad getting this one back in proper position. Al least no worries about bending the tank. 4 Quote
Popular Post Coop Posted September 1, 2025 Popular Post Report Posted September 1, 2025 On 8/30/2025 at 4:35 PM, wtnhighlander said: Tom, I've always heard it's faster to do it right than do it over. Someone must have been timing you! I’ve read several novels written by a retired Navy Seal that quotes their mantra of “Slow is smooth, smooth is fast”. 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.