wtnhighlander Posted July 21 Report Posted July 21 A request for advice, please. I am preparing to build some extension wings for my old tablesaw, from mdf with Formica countertop laminate applied. DIY, not applied from the factory. My main concern is achieving a smooth edge. Is it better to laminate the entire mdf sheet, then saw out my components, or to break the mdf down first, apply the topping, and flush trim with a router? I can see it being easier, in my current situation, to laminate first, then saw, but I'm worried about chipping the laminate edges. 1 Quote
gee-dub Posted July 21 Report Posted July 21 For MDF the secret is support. MDF has no figure, it has no grain. It is not self supporting. When you frame the extension table be sure to add in a "web" or "ribs" of supporting structure. It is easy enough to do out of scrap hardwood most of us have laying around and will pay dividends going forward. I ran an MDF side table for many years that was not plastic laminated. I simply flooded it with BLO and paste waxed it. This side extension is still in use 20 years later at my brothers house, no formica required. This may be one of the hidden benefits of living in a desert basin so I don't know that it would hold true in Tennessee. If you laminate one side of the MDF you will want to laminate the other as well as the sides. You can also "glue size" the sides in lieu of laminating. I have never been sorry that I had an expanded work surface on my tablesaw / router table area. You will be glad to have put out the effort. 2 Quote
Popular Post Coop Posted July 21 Popular Post Report Posted July 21 Recently I had to replace my router table top which is an extension of my ts. I couldn’t find an affordable piece of Formica so I bought a laminated shelf from Lowe’s. I cut it to dimension on the ts with a fine tooth blade with the face up and it came out very smooth. I roughly cut the hole for the router with a jig saw and using the old top as a template, I finished the hole opening with a router and a straight cutting bit and bearing. It too came out very smooth. I puta 1/2” hardwood band around three sides for looks and to keep from having a sharp edge from the laminate. 4 Quote
Mark J Posted July 21 Report Posted July 21 10 hours ago, gee-dub said: If you laminate one side of the MDF you will want to laminate the other as well as the sides. Why so? Does MDF move with humidity like lumber? 1 Quote
Popular Post gee-dub Posted July 21 Popular Post Report Posted July 21 @Mark J - MDF soaks up moisture (even humidity) like a sponge. It is a viable material but there are special ways to work with it as far as fasteners and finishes. If one surface is sealed and another is not it is pretty typical for it to distort. It will also sag if not properly supported. I learned this on my first Rockler tablesaw extension style router table made from melamine laminated 1-1/8" MDF. My joinery always seemed to be a bit off after about 6 months or so of use. I went into nerd mode and trouble shot the issue. I found that the MDF had sagged and this was fouling the feed path. I did a rebuild of the frame and supporting structure and have been using that same table top ever since without issue. MDF sometimes gets a bad rep but is a very usable composite. You don't want to drive screws into it without a pilot hole. You don't want to use it in a wet environment. I have cabinets made from MDF that have been in service since the early 2000s that are simply sealed inside and out with shellac. They're still fine. 3 Quote
Von Posted July 21 Report Posted July 21 On 7/20/2026 at 8:30 PM, wtnhighlander said: I am preparing to build some extension wings for my old tablesaw, from mdf with Formica countertop laminate applied. DIY, not applied from the factory. Can I ask why you choose MDF? I ask because, as geedub describes, I've found MDF needs so much support when used horizontally that I seem to end up building what amounts to a full horizontal surface under it. So it's great for times when I want to make something higher or heavier, but it has so little structural value that I never reach for it as a primary surface. Edited to add: I overstate MDF's weakness above; I admit I conflated it with particle board in my head. But I'm still curious what makes it your material of choice as I almost always reach for plywood in such circumstances, perhaps with a layer of mdf above for smoothness. 2 Quote
Immortan D Posted July 21 Report Posted July 21 On 7/21/2026 at 10:16 AM, gee-dub said: MDF soaks up moisture (even humidity) like a sponge. It is a viable material but there are special ways to work with it as far as fasteners and finishes. If one surface is sealed and another is not it is pretty typical for it to distort. It will also sag if not properly supported. I made a router table top out of MDF and laminated only the top. Big mistake. It was rendered unusable within the year. 2 Quote
gee-dub Posted July 21 Report Posted July 21 On 7/21/2026 at 6:53 AM, Von said: I've found MDF needs so much support when used horizontally that I seem to end up building what amounts to a full horizontal surface under it. Support for Von's comment: The 3/4" BB ply, 3/4" MDF sandwich that makes up my current workbench. The support structure under my current router table MDF top: Both are still rockin' 2 Quote
Popular Post Tom King Posted July 21 Popular Post Report Posted July 21 I used 3/4 plywood with aluminum angles under it to keep it flat. No need to laminate a whole sheet. Just add 1/4" to every side and trim that off with the router. Lay strips of something under the laminate on top of the substrate after the contact adhesive is dry and ready. When you get it where you want it, pull the separator strips out one at the time starting on one end. 3 Quote
Popular Post wtnhighlander Posted July 22 Author Popular Post Report Posted July 22 11 hours ago, Von said: Can I ask why you choose MDF? Two reasons: First, it is the only sheet good I can find locally with consistently flat faces. Second, I am replacing webbed iron side wings & extending the surface, so I want mass to help reduce vibration. Third, I'm cheap. The only thing that convinced me to use Formica was finding it on sale near 50% the usual price. I like the surface, though. Flat, smooth, durable, and the matte white should take pencil marks nicely for imprompu sizing gauges. I expect to laminate the underside of the MDF with plywood (added thickness) and I have plenty of steel angle on hand, to make supports from as needed. My previous router table / saw wing was 2 layers of 3/4" ply. It remained flat, but the surface was wearing, and it was an add-on past the webbed iron wing, so not very large. 3 Quote
Popular Post wtnhighlander Posted July 27 Author Popular Post Report Posted July 27 So, in the brief and infrequent periods when the heat is bearable, the shop overhaul has progressed from tear-down to rebuild. I have this rough cabinet replacing the mobile stand that was under my saw: The 'chip separator' from my old bag DC is ported to the left, with 4" piping and a blast gate to the right. That will connect a router in the extension wing, eventually. More news at 11 ... 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.