Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Got the Tablesaw (finally), Now for the Blades

Featured Replies

Hello All,

Well, Santa was good to me this year. I have been saving up for a Grizzly tablesaw for years and I have finally arrived! Now I'm thinking I better get a blade or two because it wouldn't be much fun to sit there and just watch a bare arbor spinning. I'm looking for some suggestions for what to get. I looked at some previous posts but didn't find the info I was looking for, so here I am. I've seen some debate over full or thin kerf. I'm going to go for a 5hp model (1023RLWX) so power shouldn't be a problem. That being said, what are the advantages/disadvantages of a full kerf? Obviously, having to buy one blade would be nice but I realize it may be better to get two more specific-use type blades. I should also say I am not a professional woodworker (I guess I wouldn't be posting this if I was) but I would like fairly high quality cuts. The price range I'm shooting for is less than $100 per blade (I hope that doesn't draw some chuckles). Does anybody have suggestions on 2 good blades for me to get (I already have a dado stack), or even a single blade that you think I'd be happy with? Thanks!

If you've got 5HP, I'd go for full kerf. I can't think of any disadvantage if you've got the power. Maybe you could save a tiny smidgen of wood per cut with thin kerf, but I don't think that should be an issue.

Based on previous discussions here, I'd say get a Forrest WoodWorker II 40T general purpose blade. You may want to add a 24 tooth ripping blade later, but with 5 HP you may never need one.

  • Popular Post

Tommy,

In general I would say that with the saw you're talking about a full kerf blade would be ideal. Thicker kerf means thicker saw plate and therefore greater stability in the cut. Thin kerf 'saving wood' is more just marketing spin for 'your 110v saw is too likely to blow a breaker or slow down too much and burn if you cut hard, thick wood with a full kerf blade'.

I used a Forrest WWII blade for over a year and I loved it on my 3hp Sawstop but about six months ago I was given a Freud Premier Fusion (PF) full kerf blade and found that it makes wonderful cuts, either cross cut or ripping. The blade retails for just at $100, which makes it a bit less expensive than a WWII (about $115), and the quality between the two isn't measurable to my eye. Freud uses some anti-vibration relief cuts in the body of the saw and the reps like to suspend a WWII and PF blade from the arbor hole and rap the blade with a screwdriver. The WWII gives a high pitched RING while the PF gives a solid THUNK .. which shows that the vibration is certainly dampened out.

My personal test was placing a freshly ripped edge against a freshly jointed edge and with nothing but gravity pushing them together there was NO light between the pieces; no swirls, no burn..just a wonderfully clean cut. My father-in-law, a lifelong woodworking son of a lifelong cabinet maker, couldn't stop (literally...) talking about the miter cuts the PF made and how they felt so smooth like it had been sanded.

The downside of both the WWII and the PF is that they are ATB blades without a raker tooth so you will have a slight inverted 'v' at the bottom of your cuts. You can buy a special WWII with a raker tooth for flat bottomed cuts but it's about $130 if memory serves; Freud has no raker tooth PF blade that I'm aware of. Usually this isn't an issue unless you happen to use the blade for grooves or dado cutting in lieu of a dedicated dado blade, but even then it isn't a real deal-breaker. Except for the narrowest grooves you can usually take a chisel or use a nice router plane (NOT an electric router!!) to easily remove the 'gurf'..my mentors generic terms for stuff left in the cut after you finish cutting it. :)

I still like my WWII (needs sharpening) but I'll keep running the PF until it needs sharpening and then swap them out. As I mentioned, I can't say that there is a cut quality difference between the two blades but there is some monetary saving going with the PF.

Hope this made sense, if not, post up and I'll get back to ya. Also remember this: Ask ten woodworkers for their opinions on a single subject and you'll likely get 12 different answers :D

Blue

PS.. Since you didn't ask I'll put in a plug for the Freud Dial-A-Width (DAW) dado blade as well. I got so sick and tired of playing with shims on my various dado sets..they never seemed to cut right even when I'd set up the blade on a measuring jig prior to installing on the saw. Additionally, if the cut was slightly off you had to take the whole blessed thing apart to play with shimming (okay..maybe only the outer chipper and shims but still...) however with the DAW you simply loosen (not remove) the arbor nut, twist the hub one click to either widen or narrow the dado, retighten the arbor nut and try again. It saves me a BUTTLOAD of time and frustration. Again, there is a price attached ($265 or so) but, like buying an expensive saw, it only hurts until the first time you use it and realize the time/effort savings involved. When I blew my dado stack on my Sawstop (stupid mistake with an incra miter gauge) I went right out and bought a new DAW dado. Some people are under the impression that the DAW is a wobble blade I will assure you it is NOT..it cuts nice, flat bottomed dados. The hub moves the outer chipper in or out depending on which way you twist it but it stays flat to the rest of the stack hence no 'wobble'.

I'm also a long time user of WWII's who has recently switched (back) to Freud Fusions for general work. Along with the Freud and Forrest, I also like Systematic. Except with my dual blade tenon kit, I like to stick to full-sized kerfs, as it keeps my left-tilt fence cursor accurate and my sled and ZCS kerfs working. My 3HP General has no issues, I'm sure you won't, either.

I still keep a sharp WWII and Forrest stabilizer that matches a sled with a perfect floor kerf for killer crosscuts. I switched away from the WWII for daily use because of the WWII's tooth clearance created a buildup issue. I had gotten into the habit of cleaning the WWII every time I switched it out, to prevent burning on maple and cherry. Yes, everything is properly aligned... :wacko: I thought this was normal. The owner of a well-regarded woodworking school turned me on to the clearance issue and how it didn't exist on other brands of blades. In the school, the buildup was magnified with constant use on three saws, and they weren't interested in cleaning the blades so often. This may or may not be an issue for others, based on wood choice and hours of blade usage.

I also keep a 20T Freud Industrial rip handy for stock over 6/4, and 30T glue line rips for ripping stock to be edge glued. I have recently gotten back in the habit of swapping blades far more often. I use the glue lines for kerfing, spline cutting, tenon cutting, etc... If you plan your blade and saw accessory storage well, swapping is quick and easy.

I use a Forrest Dado King dado set. My shims have slots cut in them for insertion / removal without removing anything.

  • Author

Thanks for the input. You've definitely narrowed down my search. I will have a little credit left over at Grizzly after my saw and mobile base purchase so I'd like to keep my purchasing within Griz. So after searching for the blades that you all suggested, it looks like the only one they stock is the Forrest WWII. That made the decision easy! The only thing is, they don't have the 40T. The one they carry is a WWII .125 kerf 48T. I assume this is close enough to the 40T to be a good all-around blade?

WOW 5HP!!! Now that's a serious saw.  I thought I was making a giant leap from 1HP to 1-1/2HP ;-)

I won't make any suggestions on blade manufacturer or specific models. I think they all have their plus and minuses. 

But in regards to Full Kerf vs Thin Kerf I'll say this...with the power of 5HP it would be a crime NOT to take advantage of that brute force and go with a Full Kerf blade. 

As was mentioned previously, the thin kerf blades are perfect for under powered saws. For example, my old TS was originally only a 1/2HP.  When I used a thin kerf blade it greatly improved my saw's cutting stamina and I could cut 5/4 ash without blowing the circuit breakers. 

The problem was, the vast majority of my cuts would need a lot of touchup work before I could use the components. Typically, the freshly cut edge would have a bit of a bevel to them. This wasn't due to my blade NOT being squared to the table top before cutting, but instead because the blade would flex DURING the cut. 

It was almost equivalent to an undertensioned bandsaw blade leaving a "barrel" cut during resawing.  Not to mention the noise it made while the saw was running. You could hear it flopping back and forth. 

A full kerf blade will sound quieter, run smoother and will leave a much nicer cut than a thin kerf in most situations. 

Enjoy that saw...sounds like it was worth the wait. 

  • Author

Dynablue, I'll have to give them a call. I hope I don't get the response, "I don't know, it says 48 tooth." Maybe it is an incorrect listing. http://www.grizzly.com/products/10-48T-5-8-Hole-125-Kerf-Woodworker-II-Blade/T23527

hhh, many good points. I am a weekend (and occasional weekday) warrior so I can't imagine having to get through much 12/4 stock. I do have a selection of the "honey do" blades from my 10" rad arm saw that I can throw on it if I need to. I'd use those to get the stock down to a managable size before switching to the good blade. I didn't think this would be a simple decision!

Im on the other side of the fence. I wouldn't invest in dedicated rip blades. Over the years Ive tried a few and found them unnecessary. I have 5 ww2's and 6 fusions the advantage to the fusion is you get one more sharpening than the ww2. I do agree that people wait entirely to long to sharpen blades but for hobby stuff that's sort of a fact of life. Id save the the money and use it towards a good dado set. I have 2 dado kings and they perform well.

Don

Why does the fusion offer one more sharpening?

There is more meat on the carbide. Fusions average 7-8 sharpening and ww2 average 6-7 but usually 6 if you cut alot of plywood.

Don

==> I wouldn't invest in dedicated rip blades

what do you do with 8/4 and above? I find the wwii not really great for that.

GP ww2 and fusions cut 8/4 just fine. I might invest in a 30t if I cut lots of 12/4 but those are so few and far between for most people even furniture makers it really makes no real sense. Once you start working with real thick stuff the bandsaw and planer are much easier.

Don

Freud also uses a micrograin carbide which they claim allows for sharper blades. Smaller pieces of carbide mean the edges can be a bit sharper on the microscopic level. The fusion blade also uses a special grind on the side of each tooth, two or three facets instead of a flat side. They say this reduces heat in the cutline and allows for better overall finish on the kerf walls.

The only wood I have had problems with is mahogany. The internal stresses and the interlocking grain means that I've had more binding and even some burning when rip cutting. One piece was so bad I spent an hour rechecking my saw geometry but it was all less than a quarter of .001" (whatever that measurement is LOL) from parallel. In fact the closest I've come to a kickback on my Sawstop was a 3/4" thick piece of mahogany a little over 2' long. I'd jointed, planed and ripped it 4 square then was ripping that blank in half. The piece not only closed up on the back side of the blade but the side riding the fence actually popped up over the offcut side and locked in place. So glad I used my riving knife! The only damage was a very badly burned and swirled kerf rather than the mahogany sandwich I'd have eaten without that riving knife in place.

  • 4 weeks later...
  • Author

Thanks again for all the responses. I think I'll go for the 48t WW. The saw came with a 40t blade, which I'm sure is not very good but I can use for the cuts that don't have to be perfect. I recieved the saw the other day and am in the process of setting it up and I now have a question on how to wire it. The manual says the 5hp model (which is the one I got) has to be hard-wired. I was planning on getting the wire and using a plug because right now I only have one 220 receptacle which I need for other tools as well as the saw. Does anyone know why I'm not supposed to use a plug? The only thing I can think of is that the amount of current this saw will draw cannot be handled by any plug??

5hp would probably require a 30a branch circuit -- check the manual -- some motor surge at start-up may require a much higher breaker. Many use twist-lock to un-plug for blade changes. Sharing receptacles with 5hp tools is not a great idea. if you are doing things like that, then you really should get someone in to wire the shop properly.

Earlier this year I finally got my dream saw (5hp PM on a serious sale!!!) and I was told that I needed to have a minimum 40A breaker; I hard-wired a 30' cord on the saw (8-3g). First time I talked with PM one guy said 50A, the next person (who IMO knew their stuff and had been there a while) said the 40A would be more than adequate providing it was a dedicated circuit (not shared by another tool)... I used a standard dryer plug rated for that amp. The twist locks are what I wanted but were 4x the cost. As it is, my plug engages stiff enough that it's actually a little difficult to pull out of the wall.

As far as the blade, you won't be dissappointed by the full kerf WWII (I believe I have the 40T). I've cut a ton of teak which is terrrible on blades (high silica content) and it still gives edges that are as smooth and true as from the jointer. Although, I do wish I would have spent a little more and gotten the blade that gives a flat bottom cut...

Congrats on the saw! I know what it's like to save and wait, and wait, and wait... You'll love it! It's a night and day difference compared to what you're used to! At least it was for me :P

  • Author

I have a 50 amp circuit already for a welder I rarely ever use. That is the receptacle I'd like to use. The saw would be plugged in 99 percent of the time. I just don't want to run a whole separate circuit for the saw just because they say it needs to be hard-wired. Being that I have the amperage already available, does anybody know of any reason I can't use a plug instead of having to hard-wire?

  • Author

PM...NICE!!! Congrats to you too BT! I can't believe I actually have a saw like this in my shop! As you can see in my above post, I already have a 50A circuit so luckily I'm not really worried about having enough power (for once!). It sounds like a plug-in setup is working just fine for you. That's what I was wondering about. Sounds like I'm headed to Home Depot tomorrow to buy some copper and a plug. Thanks!

As long as the cable is adequate for the power load, there shouldn't be any difference. I don't have my saw hard-wired to the wall, but have a 30' power-cord hard wired to the magnetic switch for the motor.. This way I am able to move the saw around in the shop depending on what other stuff I hav ein there...

One thing I would check before you buy the wire is to check the number of wires you need. I'm used to 2 hots, 1 ground and 1 neutral (4 total); but my saw only used 2 hots and a ground wired from the factory (the neutral was not used as there isn't anything on there that runs 110v)... So, I didn't actually need the 8-3g. 8-2g is what I should have gotten but didn't know that at the time :P .. Could have saved a bit of $$$ as electrical stuff is expensive! Just ended up capping the neutral on the saw side..

If you did not buy your blades yet, I have an Infinity Super General(light use), Onsrud dado (never used) and an Onsrud rip blade (never used) that I am going to be selling. I just sold my table saw that I never really used and have no use for the blades now and will give you a good deal. Let me know if your interested if not I will just put them on ebay.

James

  • Author

Thanks again guys. I should be good with 10-2. The manual says the saw requires a 30 amp circuit. James, I'm good on the rip and dado blades and I have my heart set on the WW. Thanks anyway!

Don't completely write off the Grizzly blade. Mine is pushing a year old and still cuts like new. Doesn't splinter anything and leaves a sandpaper smooth cut.

I know I wouldn't believe it if wasn't on my saw.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.