Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Quickest finish?

Featured Replies

Hi guys/gals,

I'm in need of the quickest possible finish for a bent lamination lamp I'm making for Christmas (early present giving this weekend). I'm a little behind and won't be finished til the night before I give it.

Preferably in a spray can, I don't have any spray tools and the lamp is quite fiddly.

Doesn't need to be super hard wearing or anything as it will just be sitting on a bench.

I really don't want something that's still going to be tacky eight hours later.

Thanks!

shellack dries in min even in a damp area it dries super fast plus it has a nice shine too it and you can layer it up . or you can go with wax finishes if you want to have a mat finish.

I've been super happy wiping on thin (~ 1LB cut...) shellac on items like lamps and boxes. It dries in minutes. By THIN coat, I'm meaning similar to what might come from a fat tip Sharpie marker. You can see it drying on the spot.

Sand to 320 or smooth plane, wipe one coat, wipe another, sand 320, wipe twice, sand 400, wipe, wipe again. Lightly buff with 0000 steel wool and wax. The whole process should take less than an hour. I did 22 small boxes in ~ 90 minutes.

For hard, figured woods, like tiger maple, you can wipe, sand 600, wipe, sand 800, wipe, sand 1000, wipe... The surface and figure will amaze you. Like something you see in a jewelery store.

The key is that each wiped pass should dry almost instantly. If it doesn't, you're either using too much, or the shellac is too thick. Do not go back over wet areas, you'll remove more than you put on. The second wipe between each sanding is after you've let it dry. If you miss a spot, get it next time.

I keep the shellac in a tightly sealed bottle, and my cotton wipers in a sealed jar. I use clear shellac on many woods, and black or buttonlac on walnut, fumed oak, or other dark woods, with different wipers for light and dark shellac.

I learned this technique from Mike Pekovich at FWW, it's also been mentioned on the FWW podcast. I never would have believed this worked so well until I saw it demoed in person and tried it myself. Now, I keep a light and dark kit handy for last minute finishes on gift items.

+1 for shellac

It is also in a spray can if that's what you prefer.

For quick finishes on boxes and nickknacks I use the wax free sanding sealer. Its just a thinner cut.

Rag on your first coat. Soaks in and dries fast. Light sanding and brush on the next coat. Brushing lays on more product than rag and if you rag your 2nd coat the rag sticks. Throw a fan on it and should be ready for sanding in 30 min. Sand out brush strokes and overlap marks then reapply if needed. Sand again and top it off with paste wax.

It's a badass finish fast.

shellac or lacquer. Shellac kills fewer brain cells. Make sure you have good ventilation and a respirator if you use lacquer.

I'm new to the world of finishing, so my skills have not yet developed. However, I have had very good luck with shellac. I buy a quart of clear or amber zinnser brand shellac and apply in thing coats likt recommended. Then I buff with steel wool in between coats. Works really well, and the final product is the best I have done so far.

Only thing I'll add to what has already been suggested is if you decide to go with lacquer make sure you buy the brand Deft. They spray the best in my opinion. Many of the other brands I've used the tips clog half way through the can rendering them useless... Never had a problem with Deft..

Shellac for me, that's why I asked about dissolving flakes. I was supposed to be on the road today, but still have four drawers to make for that jewelry armoire, Thanks to shellac I'll be hitting the road tomorrow :).

  • Author

Thanks guys!

Sounds like it might be shellac. I have some left already cut, but sounds like I might need to thin it further.

My only problem is the really fiddly bits inside the shade (wooden), that a spray can would be easiest for. Might be hard getting my hand inside, and getting between slats easily - especially if I then have to sand back between coats.

Noob, even if you use lacquer, you still will have to sand between coats. That's going to take longer than the finish application. As usual, it's the prep work that takes the longest.

+1 for Deft spray can lacquer ! It is clearer and I think it dries faster, clearer and harder. Thin coats. You can sand between coats with a Scotch brite pad.

  • Author

Hey guys. Thought I'd report back. I ended up going with shellac and it worked brilliantly. I had actually already mixed up some flakes to test out a few months ago - but this was the first time I'd used it properly. I couldn't even tell you what the cut was, but I diluted it even further to ensure quick drying. I bought some spray lacquer but the drying time was too long.

I just wiped it on with part of an old shirt (not 100% cotton, so it was quite smooth and not fluffy) wadded up. It dried in minutes, I just buffed it back lightly with a green sciotch brite pad and reapplied about four times. Very, very easy all round. I was very pleased with the process and the finish. I ended up wiping a little beeswax on then off after everything to give a little more sheen. It was quite beautiful.

Now to start experimenting with different cuts and blondness and dewaxed etc.

Thanks for the suggestions.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.