Spencer_J Posted January 9, 2013 Report Posted January 9, 2013 hey all, recently my little ryobi table saw broke down one late night in december. SO.... my beloved girlfriend hooked me up (christmas) with a used 3hp delta unisaw with a 52" biesemeyer fence, the delta sliding table attachment and a few additional table upgrades. the previous owner is a cabinet maker who is getting out of the business to slow things down. I have yet to get it into my shop for a few reasons. 1. since it's a larger, more permanent tool, i have to re-design my work flow area (actually excited to get everything leveled up!) 2. how the hell am i going to get this thing home in one piece? - This thing is so dialed in that i'm afraid to take it apart or transport it because maybe things will shift?... which brings the question should i just take the whole thing apart to transport it? or should i try to keep it all in one piece? I have a ford ranger and some strong neighbors. I'm hesitant to go get the saw because my schedule is very dense and i need to minimize my tinkering time. However, it's such a huge upgrade that it will cut down my work time because of it's accuracy. thanks in advance! Quote
robjeffking Posted January 9, 2013 Report Posted January 9, 2013 If it has a wheeled base disconnect the extension table and roll in a tilt trailer use a pce of plywood if the trailer's floor is uneven. Too many things could go wrong trying to lift it up in your pickup's bed. No wheels just make a wheeled pallet. If none of the options are available take alot of pics for reference label ziplocks bags of the parts and break it down. 1 Quote
Dave H Posted January 9, 2013 Report Posted January 9, 2013 You could think about renting a small moveing van with a lift gate, maybe one of your friends or neighbors has a ATV trailer with a ramp. If moneys no problem you could hire a local moveing co. to haul it, I agree with Rob the back of the truck is too high I have this same saw I wieghs in at 500LBs so if it's just you and some buds make em big buds. Quote
CessnaPilotBarry Posted January 9, 2013 Report Posted January 9, 2013 Look closely. Chances are, you can remove a few bolts from the front, back, and right wing, which will allow the fence rails and table board to come off in one manageable piece. You're then left with the basic saw, which is heavy, but manageable by several people. Need to lighten the saw more? Cabinet saws can have the top removed with just a few bolts. The guy who bought my General 650 was putting it upstairs. All three parts were manageable with two people, and we had no issues putting it into his pickup. If the manual is not available, you put the model number in at eReplacementparts.com. You can see an exploded view of the saw, and see where the top and fence bolts are that might need to come off. Quote
wdwerker Posted January 9, 2013 Report Posted January 9, 2013 Any sliding table is going to need adjustments from time to time so you need to learn that anyways . Ask for any manuals he might have, or look them up for PDF downloads. Take lots of pictures and zip lock bag any fasteners you remove with the picture # from your camera written on it. Even the basic saw without a sliding table or long fences is a 2 man job to move at the minimum . 1 Quote
Trip Posted January 9, 2013 Report Posted January 9, 2013 I wouldn't transport unless i removed the wings, extension table and fence. As stated above, they will have to be adjusted anyway, so the odds of damaging something important goes way down if they are just removed... If you want convincing, Marc has a video on shop moving where his TS almost took a tumble... I think it's a total of 6 bolts for the wings, maybe 4 for the extension and another 8 for the fence. Just put them in separate zip-lock bags. Takes a total of about 10 minutes to dissemble and maybe an hour to reassemble/adjust on the other side. Quote
Eric. Posted January 9, 2013 Report Posted January 9, 2013 You guys are way over-complicating things. http://youtu.be/MmQhKsHcOOQ 1 Quote
tim0625 Posted January 9, 2013 Report Posted January 9, 2013 Look closely. Chances are, you can remove a few bolts from the front, back, and right wing, which will allow the fence rails and table board to come off in one manageable piece. You're then left with the basic saw, which is heavy, but manageable by several people. Need to lighten the saw more? Cabinet saws can have the top removed with just a few bolts. The guy who bought my General 650 was putting it upstairs. All three parts were manageable with two people, and we had no issues putting it into his pickup. If the manual is not available, you put the model number in at eReplacementparts.com. You can see an exploded view of the saw, and see where the top and fence bolts are that might need to come off. +1 Barry...I wouldn't like the wings - only supported by maybe 3 bolts each - going through the vibration of going down the highway; not even supported with 2x4s. Since it's so simple to remove the wings and the fence rails, just remove the outer wings and fence rails and you and 3 other brutes pick it up - cabinet with the center table still attached and set it in the truck. I have a Grizzly 5HP and two of us could have done what I described. Ratchet straps across the top holds it in place in case of any NASCAR turns. Quote
Clavius Posted January 9, 2013 Report Posted January 9, 2013 I bought a used Unisaw that came with a mobile base so I simply rolled it onto the moving van's lift gate without removing the table extensions. The truck cost $150 to rent, but I was able to relocate the saw entirely by myself. No back strains and I was done in an hour. Quote
Spencer_J Posted January 10, 2013 Author Report Posted January 10, 2013 great advice. thank you! i enjoyed watching mark's video... I am going to try to seek a lift gate truck since the saw is in manhattan. (trailers don't tend to do so well in the big city) also, i will be prepared to disassemble if need be. I will take tons of pictures and post some up next week. Quote
arcwick08 Posted January 15, 2013 Report Posted January 15, 2013 I know I'm late to the party, but I literally JUST transported a unisaw configured like this! We used a pickup with a hydro lift gate. 90% of the weight is centered over the cabinet. The extension table and base just hung over the edge and we steadied it while it lifted up, then slid it back into the truck. I have a basement shop, so when I got it home, I took the table, extension, fence and top off. Each of the parts was brought down by two people (wife and I) and the cabinet/motor assembly I brought down the stairs carefully with a hand cart. Quote
Spencer_J Posted January 19, 2013 Author Report Posted January 19, 2013 perfect! So during the process of preparing the saw to go down the elevator, i quickly realized that i'd have to take the whole thing apart. I came prepared with my installation tool bag with wrenches, hex keys, sockets etc. once everything was disassembled, I was interrupted and had to leave quickly & the soonest i was allowed back was the following tuesday. talk about taking the wind out of my sails... the shop that the saw is located in was full of industrial woodworking tools so that made it a very fun and educational trip 65 miles away and back. They have a large loading dock so getting it into my truck is easy and my neighbor has a forklift so i think i will be okay. I am so glad that i got information from you guys before hand though... i have some images so far. i didn't get a picture of the saw with the rails off but i will next time. Quote
Spencer_J Posted February 5, 2013 Author Report Posted February 5, 2013 finally got the saw transported & setup... its wonderful! the saw has been pretty heavily used, i got a couple new zero clearance inserts from leecraft. i love the side & front adjustment screws for a snug fit. I've certainly got a little work to do spiffing up the saw but what is an old unisaw without new love?! thanks a lot for all your help everyone... Quote
Spencer_J Posted February 14, 2013 Author Report Posted February 14, 2013 it runs pretty well! I got the top, extensions, rails & fence waxed up and what a night & day difference. the 3hp motor is what i wish i'd been using all along. I cut through a 3 ft plank of 2" thick heart pine and it felt like i was cutting plywood. when i cut plywood it felt like air.. As any excited forum go-er would do, i've created a punch list of upgrades with links to make this saw my own. Since i make stuff for a living, it's not going to happen all at once. I think this process will help me come up with longer term solutions to which i can rely on as opposed to trying to hot rod it in a weekend. replace the arbor bearings & new belts ( a little vibration, belt set, and slightly more noise than seems normal) steve shanesy's unisaw restoration video series: table top blade guard & dust collection shroud gordon sampson's free plan for a splitter-less collector: http://www.woodcentral.com/bparticles/overarm_guard.shtml his table saw is set up exactly where mine is in the garage so i think this design will work pretty well. MJ splitter marc's video sold me! : http://www.thewoodwhisperer.com/videos/microjig-mj-splitter/?category_name=whisper-minis%2Creviews%2Csafety clean up & reface my biesemeyer fence (it's been used heavily and was one of the first models to come out, so it has worn down formica sliders as opposed to the UHMD, or HDPE plastic sliders) found this article from steve shanesy about refacing the fence: http://www.popularwoodworking.com/woodworking-blogs/editors-blog/biesmeyer-table-saw-fence-removal-and-refacing after combing through several biesemeyer refurbishment searches i came up with a few resources that will help me find my way: this guy has good images for reference: http://www.sawmillcreek.org/showthread.php?166420-Biesemeyer-Refurb instructions on how to convert to the replacable plastic pads, sorta..: http://www.deltamachinery.com/faq/303-can-i-refurbish-my-older-biesemeyer-commercial-fence this site seems to have parts at slightly lower prices, and certain items that are not available from others, also tons of info on delta parts & manuals (i found my sliding table attachment manual here!!): http://www.mikestools.com/biesemeyer-replacement-parts_1418.aspx?page=1 or i could skip the whole refurbishment process and get a VSC tools extrusion fence modify the delta sliding table. - i think delta really missed the mark on this thing. almost all the reviews i've read talk about the overly complex adjustments, poor quality parts etc. I do agree with most of it but at the end of the day, it's not worth chucking. the benefits significantly outweigh the drawbacks. i just wish it wasn't so touchy! if anyone reads this and has gotten a hold of the delta sliding table, the article will allow you to justify keeping it. smart upgrades from Phil Bumbalough :http://benchmark.20m.com/tools/Unisaw/UnisawSlidingTable/unisaw_slidingtable.html replace the right hand extension table with a slab of 1" black epoxyn which we got at a garage sale for $2. I will also create a hole to fit a table top router setup. pretty serious stuff... makes me think about mixing chemicals on my extension table.. hmm.... http://www.epoxyn.com/epoxynproducts/products/epoxy+resin+products/components/balance+tables.asp after that, i'm pretty much set for life! i am so lucky to be able to have a shop, tools & unlimited brain space to grow. I would have never felt comfortable getting into a used table saw if it weren't for this forum!! thanks guys. Quote
Spencer_J Posted March 22, 2014 Author Report Posted March 22, 2014 just put in some new belts today and WOW. what a difference. i got some of the green V link belts from HF, and only installed two, the saw is so much quieter and my push stick doesn't vibrate off the table now Quote
Tom King Posted March 23, 2014 Report Posted March 23, 2014 I guess this thread started before I joined the forums. For what it's worth, we transport my old Unisaw all the time completely setup, including the long right wing, and overhead dust arm. It stays on a rolling base. We roll it into the frontend loader bucket to raise it in and out of a house, and it rides around inside the trailer between big jobs. Once in a while it gets rolled out on the back flap of the trailer for use if we need it. It's never gone out of adjustment. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.