William Russick Posted July 12, 2013 Report Posted July 12, 2013 So I recently got some great advice on here about routers and I thought I could do it myself. I've been looking for quite sometime and can't find anything suitable for my current needs. I need at least 1.5 horsepower and was strongly recommended to have a 1/2 collet to use bigger bits. My price range is about 100 bucks and would like no to skew too far from that, to help with this, I believe I'll just end up selling my Kreg master jig. If any of your pros out there have any advice, I'm very thankful. All opinions are valued and respected here. Quote
pghmyn Posted July 12, 2013 Report Posted July 12, 2013 For that price range, I'd be pretty hard pressed to pass up this router: http://www.amazon.com/PORTER-CABLE-690LR-11-Amp-Fixed-Base-Router/dp/B00005QEVQ/ref=sr_1_1?ie=UTF8&qid=1373647544&sr=8-1&keywords=porter+cable+router $125 with free shipping. I'm almost positive this is the one that Steve Ramsey (Woodworking For Mere Mortals on YouTube) uses all the time and he seems quite satisfied with it. Quote
ChetlovesMer Posted July 12, 2013 Report Posted July 12, 2013 Okay, if you're a newbie my suggestion is to figure out what you are going to do with the router first, then get the appropriate tool for the job. The current issue of Woodsmith magazine has an article on which router does what. Beyond that, I can tell you there are a lot of routers on ebay and craigslist, which my offer you a cost savings if you can live with a used tool. Quote
rodger. Posted July 12, 2013 Report Posted July 12, 2013 You may regret selling your kreg pocket hole kit. It's awesome for face frames, which is a very common woodworking practise. 1 Quote
Byrdie Posted July 12, 2013 Report Posted July 12, 2013 I have the same Porter Cable mentioned above. Came with both a .25 and .5 collet and a fixed base. They had a kit that came with both bases but that was quite a bit more and I was fund limited at the time. It was just under $100 (99 - something) and I got it at Menards. I am nothing but satisfied with it. 1 Quote
Tom King Posted July 12, 2013 Report Posted July 12, 2013 http://www.woodcraft.com/assets/rebates/PCRouterRoundUP_2013.pdf Quote
Dan S Posted July 12, 2013 Report Posted July 12, 2013 One really important thing to remember about the single speed routers is you can't run large bits in them as they spin to fast. this page has some good reference speeds on them. http://www.rockler.com/articles/router-bit-basics.cfm Quote
William Russick Posted July 12, 2013 Author Report Posted July 12, 2013 Is that 690 a variable speed or just one strict speed? I'd like something with variable speed so I can run the bigger bits. I don't plan on doing anything super heavy duty until I build my tool collection and will be able to give you guys advice someday. LOL In my dreams. Quote
wdwerker Posted July 13, 2013 Report Posted July 13, 2013 I have at least 6 or 7 of the Porter Cable 690 routers in my shop. Some of them have been thru daily hard use for 6 or 8 years before dying. I keep the carcasses to scavenge parts from. They will handle a good sized bit, but not the big ones. Great sturdy reliable router to start off with. Quote
knotscott Posted July 13, 2013 Report Posted July 13, 2013 The PC690 is a solid performer. The Hitachi M12VC is another great choice....variable speed, very quiet, nice and light....refurbished brings it in below budget. The newer Craftsman routers also get good reviews as good value, and will leave a little money for router bits. Get your hands on as many as possible, and be sure it feels good to you if it'll be used for hand use. If it's going in a router table, variable speed is a must. 1 Quote
Dan S Posted July 13, 2013 Report Posted July 13, 2013 I just wanted to clarify that that my comment was about safety, more than the routers ability. I think any router that will accept a 1/2 collet" has bearings & a shaft strong enough to spin even the largest bit at max rpm. I haven't done the math but at max speed a big bit probably has enough energy stored in it to rip the router right out of your hand if it bit something hard. They will handle a good sized bit, but not the big ones. Great sturdy reliable router to start off with. 1 Quote
William Russick Posted July 13, 2013 Author Report Posted July 13, 2013 Thank you all very much. Looks like I'm going down the the store tomorrow and getting the 690 to start with, I'll upgrade in a year or so. Thank you all very much, you're all so very knowledgable and I'm very grateful. Quote
Byrdie Posted July 13, 2013 Report Posted July 13, 2013 >$100 + variable speed = good luck, probably shopping used and even then, good luck. Quote
Spencer_J Posted July 13, 2013 Report Posted July 13, 2013 Im a little late to the party but: used used used. There are so many people with excess of stuff just floatig around out there. Craigslist has given me some wonderful gifts and i've met some really great people through CL. My first router was a crappy australian plunge router that an old guy gave me because it was " too crappy"... "Here, take it away, please!". I used that for five years as my only router to make custom furniture for NYC clients. Once i cut my teeth on that one i expanded to many different routers for different bits etc. good luck and be safe! Quote
PeteJr Posted July 14, 2013 Report Posted July 14, 2013 I strongly recommend a variable speed Dewalt DW618 Quote
wtnhighlander Posted July 14, 2013 Report Posted July 14, 2013 All of the above is good advice, but given your budget and desired features, I would certainly have to at least consider this: http://www.harborfreight.com/2-1-2-half-hp-plunge-router-37793.html Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.