Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Grr-ripper vs. blade guard and other questions

Featured Replies

Hi -

 

I'm thinking of getting some grr-rippers and have some questions.

 

1. I am wondering if in practice they replace the blade guard in all ripping operations?  Or do you put the blade guard back on if ripping wide stock? (I have a sawstop with both riving knife and guard with dust collection). In principle you could put the blade guard back on for wide boards, but does that really happen?

 

2. I suppose I should get a pair for ripping long stock? The hand over hand process looks a bit awkward but I guess you'd get used to it.

 

3. Are any of the add-on gadgets definitely worth buying?

 

Thanks & Happy New Year!

 

Cheers,

Brian

I like the grippers and use them often.  I have to be honest, the blade guard has never been on my saw but, it does have a riving knife.

Same here. I have a single grr-ripper and a riving knife. I don't use the blade guard. I plan to get a second one but haven't yet. I have the 1/8" leg and back leg attachment. I have ripped as narrow as 5/16" with it with no problems. I use it a lot with my router table as well.

-Darryl

I removed my blade guard over a decade ago. They are useful for people that otherwise can't keep their fingers out of the blade but in general I don't believe them to be a particularly useful safety device. The Grippper is nice for narrow stock.

- sent via Tapatalk

Same here.  Riving knife, no blade guard.  Some people will say that's stupid, but I don't care.  It feels safer without it on because I have a better picture of what's happening during a cut.  The blade guard obscures my view and gets in the way.

 

You don't need two Grrrippers, though it may be handy for pushing through heavy stock...in which case I would probably be ripping at the bandsaw anyway.  For long boards I feed the majority through with just my hands, then pick up the Grrripper for the last ten or twelve inches.  I use a push stick for any cut wider than three or four inches.  Grrripper is reserved for skinny rips only.  It's a great accessory, but it only really shines for skinny rips.  Everything else can be done safely and easily with traditional push blocks or sticks.

I've used my Grr-Ripper for ripping 8/4 stock for cutting boards, etc. My saw was sans blade guard when I bought it. I've got microjig splitters on my insert plate to use along with the Grr-Ripper. 

Hi -

 

I'm thinking of getting some grr-rippers and have some questions.

 

1. I am wondering if in practice they replace the blade guard in all ripping operations?  Or do you put the blade guard back on if ripping wide stock? (I have a sawstop with both riving knife and guard with dust collection). In principle you could put the blade guard back on for wide boards, but does that really happen?

 

2. I suppose I should get a pair for ripping long stock? The hand over hand process looks a bit awkward but I guess you'd get used to it.

 

3. Are any of the add-on gadgets definitely worth buying?

 

Thanks & Happy New Year!

 

Cheers,

Brian

 

 

I think if you learn to use the guard, eventually it will just become second nature. The older guards were unsafe but the newer designs work fine. The gripper looks handy for tiny work like jeweler boxes and the like. I don't see it as a necessity by any means for general woodworking. I have a few Bench Dog push blocks that work well when needed. If I need a block that will run into the blade I use a Quickley. 

If I can semi side track this for a moment. I took the riving knife off of mine when I got the ts. After reading from a bunch of you guys on here, I decided I really ought to put it back but couldn't find it so I purchased another one. I installed it, only to find I had a thin kerf blade on the ts and the knife, I guess, was made for a thick, 1/8" blade. What do you do in this case?

If I can semi side track this for a moment. I took the riving knife off of mine when I got the ts. After reading from a bunch of you guys on here, I decided I really ought to put it back but couldn't find it so I purchased another one. I installed it, only to find I had a thin kerf blade on the ts and the knife, I guess, was made for a thick, 1/8" blade. What do you do in this case?

 

Buy a thin kerf riving knife or full kerf blade.

Or you can grind down the knife, I guess.  One side of the knife lines up with one side of the blade, and the other side of both the blade and the knife are held by nuts or something adjustable.  Remove material from the "adjustable" side of the knife.

 

But I'd just return that knife and exchange it for a think kerf knife.

Sounds like the logical solution but was wondering if I use the thin kerf knife, would it offer me the same protection if used with a full size blade? Or, do you switch knives, when you switch blades.

I've got a Grrr-ripper, but I hardly ever use it.  I've got the blade guard on all the time, except when making non-through cuts.  I use the gripper on a through cut when the fence is too close to the blade so I have to remove the blade guard.

Sounds like the logical solution but was wondering if I use the thin kerf knife, would it offer me the same protection if used with a full size blade? Or, do you switch knives, when you switch blades.

 

No.  The purpose of the knife is to prevent the wood from closing on the blade.  Sounds to my like you need 2.

No.  The purpose of the knife is to prevent the wood from closing on the blade.  Sounds to me like you need 2.

Kind of what I was thinking. Thanks

Sorry OP for the hijack

I have the same Sawstop setup as the OP.  I leave the guard on for almost all cuts including miter cuts, primarily for the improved dust collection.  I also have a Grripper which I purchased soon after they were introduced - It get used on narrower rips, 70mm and less, and the guard comes off for those.  Do not really see the need for two Grrippers.

Everything comes off when I use the gripper. Suppose I could keep the low pro riving knife on there....

I almost purchased a Grriper before I realized that it requires the blade guard to be removed for most cuts. As noted above its really comes into play and shines on narrow cuts where the guard would likely be removed anyway. I have the SS 3hp ts and really like the chip collection offered by the blade guard, it really helps to keep the shop somewhat chip free. So after considering plus/minus of the Grriper Ive decided to pass on getting one. Just my two cents

I use the gripper on the table saw as described above, but I use two grippers often on the router table. Having two helps keep even pressure down at the point of cutting.

I'm just like a couple of others in this thread in that I use both my SawStop dust collecting blade guard as much as possible and then use the Grripper for narrow cuts. With the blade guard taking about 15 seconds max to put on, I tend to use it more. I do have two Grrippers as I find the hand-over-hand method works well for me.

So the concensus here is...If you have a Saw Stop that won't cut you - leave the blade guard on! If you don't own a Saw Stop - Rip that baby off your saw the day you get it, and don't look back for 30 years. LOL

In addition to the fancy electronics, Sawstop made it really easy to swap the blade guard and riving knife.  They knew that many people took the blade guard off for a non-through cut and never put it back, and figured that if it was really easy to take off and put back, people would bother to put it back.

 

I think that's why Sawstop owners are more likely to use the guard.  At least, that's why I do.  Also the dust collection (but I bought the last Sawstop made with the old no dust collection blade guard).

I have a gripper but just the standard one. I always leave my guard on unless I can't given the operation. As said many times works great for thin cuts as long as you don't NOT pay attention like I didn't and hold your gripper the wrong way. But it cut through the gripper and not me.

In addition to the fancy electronics, Sawstop made it really easy to swap the blade guard and riving knife.  They knew that many people took the blade guard off for a non-through cut and never put it back, and figured that if it was really easy to take off and put back, people would bother to put it back.

 

I think that's why Sawstop owners are more likely to use the guard.  At least, that's why I do.  Also the dust collection (but I bought the last Sawstop made with the old no dust collection blade guard).

:) The guards have been industry standard before SS made saws. The entire industry made the change to make saws safer not SS. SS added the blade brake.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.