ChrisG-Canada Posted February 18, 2015 Report Posted February 18, 2015 I'm looking for your personal OPINION about which 12" SCMS you would choose. I'm looking to do fine woodworking like furniture, etc. and want an SCMS that is as good as possible (better than the 10" non-sliding Craftsman I've had for years, lol). I've just spent a LOT of money buying other tools so the Festool Kapex isn't in the budget. I'm looking at either the Makita LS1216L or the Bosch GCM12SD. As I read comments people seem split between these two. If there are other contenders, please let me know. I really like the Bosch gravity rise stand - if it works with either saw, I'll definitely look at it to. Quote
tcarswell Posted February 18, 2015 Report Posted February 18, 2015 The bosch is a fine saw. The dust collection from what I remember was a bit lacking however it could have been the setup. Best of luck. Quote
21meyer Posted February 18, 2015 Report Posted February 18, 2015 Both of the saws you mentioned are quality saws. I have owned the 10" version of both of them and recently purchased the Kapex. As far as dust collection and accuracy, neither of them are on the same level as the Festool. If you are extremely tight on space, the Bosch Glide is the way to go but otherwise I personally would prefer the Makita. In my experience, it is more accurate and has slightly better dust collection. Quote
estesbubba Posted February 18, 2015 Report Posted February 18, 2015 What are you looking to do with it? If looking to crosscut hardwoods a crosscut sled on the table saw can't be beat for accuracy and capacity. If you want to use it for construction work, etc. then it makes more sense to get it. Quote
chrisphr Posted February 18, 2015 Report Posted February 18, 2015 Ditto on crosscut sled. Sliding miter saw was the first tool I bought when getting into woodworking, in hindsight it would be among the last. Quote
Keggers Posted February 18, 2015 Report Posted February 18, 2015 I've had a Makita 10" SCMS for years. It's taken a beating and keeps on working. I can't complain about the accuracy but the dust collection leaves a lot to be desired. I checked out the new 12" Makita at Grizzly this past December and the basic design is the same as what I have. I would buy another one when the time comes. Quote
Cochese Posted February 18, 2015 Report Posted February 18, 2015 I have a Hitachi C12RSH. Laser is dead-on, took some minor fiddling to get everything locked in to major angles. I re-check it every now and again, but I use it all the time. It's a major component of my shop work. Sleds are good for smaller objects. Quote
collinb Posted February 18, 2015 Report Posted February 18, 2015 I've also been looking, but more out of curiosity. The company that intrigues me is Hitachi. They build some fine equipment but it has to be the ugliest stuff out there. All that black and green looks like something out of a comic book. I would personally probably go with a (used if possible) DeWalt. We have a parts store almost around the corner so maintenance would be simple. The Hitachi I looked at just didn't seem to slide as smoothly as DeWalt or Bosch. Quote
wdwerker Posted February 18, 2015 Report Posted February 18, 2015 I had a Hitachi, it was ok replace it with a Dewalt. The Makitas are nice as well. I've looked at the Kapex but just don't need it at that price. I use a sliding crosscut table for accurate part crosscuts. But you can't beat a SCMS for quick angle cuts. Quote
shaneymack Posted February 18, 2015 Report Posted February 18, 2015 I would not use a 12" for fine furniture. I have a 12" dewalt and had a 10" bosch. The bosch being a 10" is more precise. I just swapped my bosch for a kapex and the accuracy is even better. Doing mdf moldings, or just rough cutting your lumber but i wouldn't trust a 12" for fine work. That said i think the makita and bosch are both great saws. I would personally choose the bosch. Quote
Woodenskye Posted February 18, 2015 Report Posted February 18, 2015 Hitachi is the saw I have, adding a good blade and taking time, I can get extremely accurate cuts. Plus it is more compact than my 10" Bosch which is used for rougher work, but still very accurate. Quote
AstroDave Posted February 18, 2015 Report Posted February 18, 2015 I picked up a Hitachi C10FSH cheap and love it for quick cuts. I haven't built my cross cut sled yet. I find the Hitachi to be very accurate with a very nice cut. My only experience was with a Rigid non sliding CMS of which the Hitachi is vastly superior. Quote
Andrew Schicho Posted February 18, 2015 Report Posted February 18, 2015 Recently grabbed myself a dewalt 12 inch blade ~16 inch slide its super smooth in every way looks extremely well built and has some really great repeat ability with hard stops that are highly adjustable. Seems like a great tool and is wayyyyyy more accurate than any I've ever used. The dust collection is impressive in my opinion but again its the best one I've ever used I've not touched a kapex but 1200 for a miter saw seems absurd. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.