Brendon_t Posted April 6, 2015 Report Posted April 6, 2015 Sorry, that wasn't punny at all. Back at it, I've seen some great reviews of the festool line of Sanders between the Rotex and the Ets 150. I've replaced the pad on both my dewalt and rigid ROS units within the last year and both are needing it agAin. I'm getting sanding disks shooting off of the pads constantly. Knowing I would like to upgrade my sanding tools, I am thinking about picking up the two Sanders above ( one for heavy duty removal and one for finishing) but I do not own and never plan on owning one of the CT vacs. 1) Is there a way to hook the festool hose to a normal shop vac? 2) Would the high velocity airflow suck the sanding pad down onto the surface possibly leaving residual sanding marks? Thanks for any knowledge you attempt to impose. BT Quote
Tom Cancelleri Posted April 6, 2015 Report Posted April 6, 2015 If you hook it to a regular shop vac you will create suction to the surface causing pig tails in your workpiece. You can circumvent this by making an adapter with holes in it that suck air from outside of the sander to reduce the amount of suction. it's a delicate balance. Honestly, the CT is well worth it, I also said that's an expensive shopvac I see no real benefit, until I bought it. Game changer for sure. Quote
Coop Posted April 6, 2015 Report Posted April 6, 2015 Since both of my ros are black and grey and black and yellow, the only help I can impose is to say, yes that "Festion" was pretty catchy Quote
Janello Posted April 6, 2015 Report Posted April 6, 2015 There are some cheaper alternatives out there for shop vacs with variable suction. While still not cheap, the DeWalt and Bosch are considerably less and do the same thing. Quote
..Kev Posted April 6, 2015 Report Posted April 6, 2015 I would suggest a CT with them but, you can use a shop vac. You won't regret the purchase tho. Quote
Brendon_t Posted April 6, 2015 Author Report Posted April 6, 2015 I've got 3 shop vacs all bagged with hepa and two have a variable connector. By rotating a collar counter clockwise, it opens up 1/2" wide gaps about 2" Long allowing false air to enter. They go between full force at full closure to barely picking up a piece of paper when at wide open position with 3 "holes" uncovered. Guess I should have included that too. Does festool make a connector for their hose to a standard 2 or 2.5" hose? Every one I've seen looks like the locking festool type Quote
wdwerker Posted April 6, 2015 Report Posted April 6, 2015 I used a Fein vac for years w my Ets150/3 made a suction reducing ring w holes and a cover to adjust. A few O Rings made the hose stay on the sander Quote
Cochese Posted April 6, 2015 Report Posted April 6, 2015 I've got 3 shop vacs all bagged with hepa and two have a variable connector. By rotating a collar counter clockwise, it opens up 1/2" wide gaps about 2" Long allowing false air to enter. They go between full force at full closure to barely picking up a piece of paper when at wide open position with 3 "holes" uncovered. Guess I should have included that too. Does festool make a connector for their hose to a standard 2 or 2.5" hose? Every one I've seen looks like the locking festool type I have a Bosch hose that plugs directly into the tools. I can check tomorrow to see how well it plugs into a Ridgid vac. All else fails you could buy it, and modify it to your needs. Quote
krtwood Posted April 6, 2015 Report Posted April 6, 2015 If you are wearing out pads that fast then you are putting too much pressure on the sander and you'd best learn not to do that before you get the Festool because not only does the sander cost 3-4x as much but so do the replacement pads. Quote
Brendon_t Posted April 6, 2015 Author Report Posted April 6, 2015 If you are wearing out pads that fast then you are putting too much pressure on the sander and you'd best learn not to do that before you get the Festool because not only does the sander cost 3-4x as much but so do the replacement pads. intentions underStood. The pad issue is a commonly document issue on the rigid unit. There is almost zero suction to remove heat and waste materials. It's a $48 unit with an $8 replacement pad. If your saying festool Sanders have the same pour heat dissipation, then maybe I'm pointing in the wrong direction Quote
tim0625 Posted April 6, 2015 Report Posted April 6, 2015 intentions underStood. The pad issue is a commonly document issue on the rigid unit. There is almost zero suction to remove heat and waste materials. It's a $48 unit with an $8 replacement pad. If your saying festool Sanders have the same pour heat dissipation, then maybe I'm pointing in the wrong direction According to their video the same fan that pulls in air for the motor circulates it under the pad keeping it cooler and the vacuum system pulls the dust out through the holes in the sanding pad Quote
dwacker Posted April 6, 2015 Report Posted April 6, 2015 With standard shop vacs you can do the same thing as built in central vac systems which is use a srv valve. Adjust the spring loose so that it pulls the valve open under light pressure or what ever pressure you choose. If you burning pads that is operator error. Quote
krtwood Posted April 6, 2015 Report Posted April 6, 2015 intentions underStood. The pad issue is a commonly document issue on the rigid unit. There is almost zero suction to remove heat and waste materials. It's a $48 unit with an $8 replacement pad. If your saying festool Sanders have the same pour heat dissipation, then maybe I'm pointing in the wrong direction I'm sure having the vacuum on it makes a difference. All I'm saying is back when I shared a shop and a ROS with my dad he would use it on one project and the pad would be toast. The original pad on my ETS 125 lasted 5-6 years. It wasn't always hooked up to a vac. The replacement was about $30 but it started to come apart in less than a year. I ended up picking up a dewalt on sale for less than the cost of a pad for the Festool. I've been using it for a couple years now and the pad still has plenty of stick. It's almost always hooked up to the vac. Quote
jmaichel Posted April 6, 2015 Report Posted April 6, 2015 I don't think you would really need both an RO and an ETS. I would look at getting an ETS 150/5 and then complementing it with the DTS 400 or even the RO90, this will give you more versatility than ETS 150 and RO 150 would. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.