Recommended Posts

Posted

I picked up a craftsman 10 inch table saw on craigslist for cheap a couple weeks ago and I've been sawing lumber like a champ ever since.  Up to this point, its all been pine, but yesterday I tried to rip a 3 inch piece of purple heart.  I'm not sure if the friction between the blade and wood caused all the smoke or if it was the motor.  Either way, my garage was full of smoke before I got more than an inch into the board.  Lesson learned.

Posted

Often, if the fence is not perfectly parallel to the blade, the wood can pinch between the fence and blade causing friction and generating heat. Purpleheart is super dense.

I agreed with the title statement but you can't always blame the saw first. A bit of adjustment and the proper feed rate could have you still cutting dense wood.

Posted

I picked up a craftsman 10 inch table saw on craigslist for cheap a couple weeks ago and I've been sawing lumber like a champ ever since.  Up to this point, its all been pine, but yesterday I tried to rip a 3 inch piece of purple heart.  I'm not sure if the friction between the blade and wood caused all the smoke or if it was the motor.  Either way, my garage was full of smoke before I got more than an inch into the board.  Lesson learned.

It is really easy to tell wood smoke from burned out motor smoke.  Was it massively chemical smelling and really nasty toxic?  Then it was the motor.  If not it was the wood and a good blade with the right feed rate it could well manage.

Posted

Most resinous hardwoods will tend to smoke some unless you maintain proper setup with the fences, keep a sharp blade with the proper tooth count and not try to force feed the saw. The size and power of the saw will determine to some degree what you can cut safely!

Posted

==>or the lumber.

didn't think of that -- case hardening will stall-out a 5HP easy... Been there, done that...

 

==>massively chemical smelling and really nasty toxic?

hopefully, the saw has a MS/CI and it would pop before frying the windings... But as said above, we need a bit more info to offer advice...

 

==>5hp cabinet saw can deal with a twisted board or out of square fence

Been there, done that as well...

 

==>but it is still bad practice

and unsafe... really unsafe... shot a stick into a wall with a badly-aligned fence -- that was exciting...

Posted

Purpleheart is a beast...dense and oily.  My 3HP will struggle with it if my blade isn't sharp or the board isn't dead flat.  I wouldn't even attempt 8/4 exotics on a contractor saw.  Like these guys said...rip blade, sharp, thin kerf, and flat, straight stock.  And at the risk of sounding snobbish, I'll add...upgrade your saw if you plan to work with exotics often.

Posted

I always call jobsite saws contractor saws.  That's probably inaccurate but that's what I call them.  Because that's what contractors use. :)  I call contractor saws hybrids.  I should probably work on my terminology.

 

I mean any saw that you can pick up and throw in the bed of a truck.  Which I wouldn't recommend for fine furniture.  Queue the tool snob police.

  • Like 1
Posted

3" purple heart is a tall order.  There are several variables involved that many folks don't always address.  Proper blade (kept clean and sharp), proper saw setup (fence, splitter, insert, motor, belt, pulleys, belt tension, alignment, etc), flat/straight stock, good technique, and adequate electrical supply are all part of the equation.  Odds are good that there's a specific cause or causes that go beyond blaming the whole saw.  A decent 24T thin kerf ripper should help....Freud Diablo, Irwin Marples, DW Precision Trim, or CMT ITK Plus are all good buys at < $30.

Posted

showing how green I am yet again, I see.  I can say for sure, the fence kinda sucks, as it is quite difficult to keep it aligned perfectly straight.  I waxed it down and that helped a lot, but it could still be out of whack.  

 

I bought a brand new blade for it making sure it had a good amount of teeth, but *blushes* didn't know to check the kerf or even cross cut/ripping blades.  

 

Of course, I am pretty new to woodworking completely, so it could have a LOOOOOOT to do with technique.  

 

Looking at everything again this evening, I see that it wasn't the motor, it was the wood, (which smelled kind of nice).

 

and for the tool snobs (which I say lovingly), this old thing is just here to keep me occupied until I get enough $$ saved up for a proper shop saw.

Posted

I made this mistake early. I thought a 60t blade would give me incredibly smooth long beautiful glue ready joints. All I did was burn a bunch of wood. I then bought a decent 24th for ripping and found out I hate changing blades all the time.

I've since thrown a marples 40t combo blade on and really like it. It's full curf which I wish it wasn't but works great.

Posted

Wanna talk about a nasty blade. I've got a Freud 18 tooth blade with 1/8" kerf and matching 1/8" plate. Guy I bought the saw from was ripping 8/4 cherry for making flooring for his house that he built. A clean cut it does not leave.

  • Like 1
Posted

I made this mistake early. I thought a 60t blade would give me incredibly smooth long beautiful glue ready joints. All I did was burn a bunch of wood. I then bought a decent 24th for ripping and found out I hate changing blades all the time.

I've since thrown a marples 40t combo blade on and really like it. It's full curf which I wish it wasn't but works great.

 

haha sounds like this was my exact mistake.  I figured, this is an OLD saw, might as well get a new blade to ensure sharpness and I hear more teeth gives a cleaner cut, so 60t it is.

Posted

Three inch Purple Heart, don't sell the table saw, but buy a bandsaw.

 

I've been eyeballing bandsaws.  I was going to put it off until after the table saw, but I might have to dip into the table saw fund to get a bandsaw first.

Posted

haha sounds like this was my exact mistake. I figured, this is an OLD saw, might as well get a new blade to ensure sharpness and I hear more teeth gives a cleaner cut, so 60t it is.

I'll go out on a limb and say that is most likely, one of the major issues you burned so badly. There very well may be others but that many teeth are designed for a crosscut and sheet goods. Definitely not ripping big chunks of a super hard wood.

I'd be interested to see how it did with a sharp 24th thin kerf blade, all else unchanged.

Posted

So many things are wrong here you're lucky your saw is still running and you have all your fingers.  I missed the 3" part.  There's no way I'd get 12/4 purpleheart anywhere near any table saw except for joinery...especially an underpowered saw like yours.  What Carus said...bandsaw.

 

For ripping, you never use any blade with more than 40 teeth...and 40 tooth combo blades are mostly suited for 4/4 rips.  I wouldn't recommend cutting any 8/4 material harder than poplar with your saw with a 40 tooth blade.  For that you need a good quality, thin kerf ripping blade with 24 teeth.  The saw you have is not capable of handling 12/4 material safely, especially a species as dense as purpleheart.  Pine, maybe...still not a great idea.

 

Number of teeth does not equal cleaner cut...it's more about how those teeth are ground and using the correct blade for the correct cut.  More teeth and high ATB grind is for crosscuts, fewer teeth and flat grind is for ripping.  You need one of each unless you're lazy like most of us...and use something like a Forrest WWII 40 tooth combo blade...which will do a decent job of both rips and crosscuts in 4/4 material.  With an underpowered saw, you pretty much HAVE to have a dedicated rip blade if you plan to use 8/4 material.

Posted

With an underpowered saw, you pretty much HAVE to have a dedicated rip blade if you plan to use 8/4 material.

I have read this a hundred times and although I respect the knowledge you have gained over many many more years ww'ing than me, I simply do not agree.

My delta 1.5 hp saw is wholly under powered but I have never not been able to cut something thick that was milled properly.

When building the door, I ran through 100 bf of 10/4 red oak without problem. AS LONG AS IT WAS MILLED PROPERLY. If I put a frown against the fence, it would certainly slow down the blade as it caught.

I can't say it's all technique because I have never owned a heavy hp saw, what I do now I've always done.

Just my $.02

Posted

I'm only speaking from my own experience.  When I got started I used a Dewalt jobsite saw for a number of years.  It would rip 4/4 S3S hardwoods okay with a combo blade, but as soon as I started working with 8/4 I had problems.  I bought a thin kerf Diablo rip blade, which isn't the greatest but not too bad...and it still struggled to get through most thicker stock cleanly and without burning.  Pushing it through quickly bogged down the saw and slowing down the cut caused burning.  When I finally upgraded to my cabinet saw I found out what ripping is supposed to feel like.  All I know is ripping 8/4 material on a jobsite saw sucked, at least in my garage.  And yes, the fence was straight and the stock was flat and square...it was underpowered, plain and simple.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 41 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined