bigarm Posted January 3, 2016 Report Posted January 3, 2016 Let's pretend you are going to get a new router table and router. The router would be dedicated to the table and would never need to come out as you already have a very nice router for other uses (Festool 1400). The table would need to be able to be on wheels and fit through a regular door (for storage as shop is too small). It would be nice if it had a lift but if it is easily adjusted it would not be totally necessary. If you wanted a lift, include the type. It would be nice if the cost was not too much, but it does not have to be cheap. It would be replacing a Bosch table top unit. Quote
..Kev Posted January 3, 2016 Report Posted January 3, 2016 Welcome to the forums Bigarm! This one's been covered a few times here in the tool section. For me.. it would is this table http://www.woodcraft.com/Product/153675/M-R-L-Excel-II-Router-Table.aspx?gclid=Cj0KEQiAqqO0BRDyo8mkv9y259EBEiQApVQD_QIg445Q8F1txc_xuiisZzVlcYxIKSZDW5AOPU7nkX8aAjjE8P8HAQ With this router http://www.woodcraft.com/product/85O28/portercable-model-7518-314-hp-router.aspx and I find it to be awesome! 1 Quote
shaneymack Posted January 3, 2016 Report Posted January 3, 2016 I have this table and love it http://www.atlas-machinery.com/40-200C/ I also have the pc 7518 that TIODS posted. Its an awesome beast. Welcome to the forum! Sent from my SGH-I337M using Tapatalk Quote
Immortan D Posted January 3, 2016 Report Posted January 3, 2016 I always require extreme measures when it comes to portability and storage because I don't have a shop. YMMV. I made my own foldable router table for 3HP Makita router and the Incra LS Super System. Very easy to store when not in use (I just hang it from a wall when not in use). Here's a video: I also made a cart for storage of the Incra fence: Quote
Cochese Posted January 4, 2016 Report Posted January 4, 2016 4 hours ago, bigarm said: Let's pretend you are going to get a new router table and router. The router would be dedicated to the table and would never need to come out as you already have a very nice router for other uses (Festool 1400). The table would need to be able to be on wheels and fit through a regular door (for storage as shop is too small). It would be nice if it had a lift but if it is easily adjusted it would not be totally necessary. If you wanted a lift, include the type. It would be nice if the cost was not too much, but it does not have to be cheap. It would be replacing a Bosch table top unit. I'd basically have what I have now: a table with an offset base to use with an Incra positioner. The Incra table and plate would be a bonus. If I had unlimited funds I'd probably switch out the Triton 3.25 router for a 7518 and a nice lift, with a micro-adjust dial built-in to the plate. Some of those down draft rings that Incra makes, too. I've had several different router tables and different configurations. Give me a heavy as all get-out table that I can move around on nice casters everyday of the week. Quote
Trip Posted January 4, 2016 Report Posted January 4, 2016 PC 7518 Motor only option Woodpecker's PRL lift Woodhaven's large top + fence + base (plans) I just looked for the Woodhaven links, but it appears that the products are no longer available... So I can't recommend any alternatives. If I had to do it again without the Woodhaven product, I'd evaluate the Incra setup. Although, I'm generally suspicious of jig/fence systems with so many do-dads... I like KISS jig/fence setups... Quote
Popular Post ..Kev Posted January 4, 2016 Popular Post Report Posted January 4, 2016 1 minute ago, Eric. said: Oooh.... Calling for Don..... 3 Quote
shaneymack Posted January 4, 2016 Report Posted January 4, 2016 5 hours ago, Immortan D said: I always require extreme measures when it comes to portability and storage because I don't have a shop. YMMV. I made my own foldable router table for 3HP Makita router and the Incra LS Super System. Very easy to store when not in use (I just hang it from a wall when not in use). Here's a video: I also made a cart for storage of the Incra fence: Macgiver at it again! Sent from my SGH-I337M using Tapatalk 1 Quote
Phil B Posted January 4, 2016 Report Posted January 4, 2016 I have a PC 7518 motor, a JessEm Mast-R-Lift II (with the incra clean sweep rings), an Incra LS25 positioner and a wixey height gauge. It's in a table of my own design. I love love love this configuration. Super fast setup, precise height positioning, precise fence positioning. Amazing versatility with the Incra fence. With the new template creation software, Lots of cool joinery is possible. If my RT vanished tomorrow, I would get EXACTLY the same set up, even if the prices were doubled. Quote
prov163 Posted January 4, 2016 Report Posted January 4, 2016 I've got the Woodpeckers router table with the sidewinder lift and micro adjust fence. It's all made in the USA including the stand. I thought the micro adjust might be gimmicky but it is a great feature. I've got the 7518 which is about as powerful as you can get short of a shaper. Great setup, at least for me. Quote
Trip Posted January 4, 2016 Report Posted January 4, 2016 Channeling Don again... We don't need no stinking router tables! 1 Quote
Guest Posted January 4, 2016 Report Posted January 4, 2016 5 hours ago, hhh said: Channeling Don again... We don't need no stinking router tables! this is no joke. If I were starting from scratch I would get a shaper instead. The footprint of a small shaper is about that of a nice router table. I have too much $ invested invested in my table (and router bits) for it to make sense. Yes I know you can get a collet to run router bits on a shaper but I think there are some issues with that. There are lots of theories on why shapers are not popular with hobbyists. My personal theory is that Norm didn't have one, so we don't either. Quote
rodger. Posted January 4, 2016 Report Posted January 4, 2016 I use a cast iron router table wing in my table saw. Love it - great space saver and love the CI. I use a big daddy Freud router in the table, and because its fairly open I just change the bits under the table (or pull the whole insert out if necessary). Quote
Paul Edgar Posted January 5, 2016 Report Posted January 5, 2016 I have the KREG table. I went all I and purchased the leg supports and casters along with the switch. I mounted a large MAKITA router in it and the bit change and height adjustments are not that bad. It is expensive, but for me well worth the expense. After use I vacuum the interior of the (homemade) storage cabinet built into the leg system and drive on. Quote
Dylder Posted January 5, 2016 Report Posted January 5, 2016 I run a porter cable 892 with a rockler lift. Its a Norm style table with a fence that used an original incra jig. The top is a yellow pine glue up on a walnut raise panel cabinet. The back and a lot of the interior structure is 3/4 ply. Quote
bigarm Posted January 5, 2016 Author Report Posted January 5, 2016 I am also considering a cast iron extension for my Delta 36-725. I can find a couple of different ones. One is the MLCS and U turn lift which is a little cheaper. The other seems to be a Bench Dog with an Incra Master R Lift II which would be a little more expensive. The U Turn says it has 3" of lift. I can't find the amount for the Incra, but it says it can do above table bit changes. The Incra can work with the Porter Cable 7518 or the Milwaukee 5625. The U Turn specifically mentions the PC, but does not mention the Milwaukee. Any info on either of these? Quote
jussi Posted January 5, 2016 Report Posted January 5, 2016 On January 3, 2016 at 1:28 PM, bigarm said: Let's pretend you are going to get a new router table and router. My ideal setup would be using an Incra fence. If you have the room then use it with on of their offset base. If not, then use a cast iron router extension wing for the tablesaw and use a combo TS fence that is both a ts and router table fence. I currently have a tablesaw mounted router table. Or if you have a festool mft, incorporate it into that. Ideally I would pair it with an Incra made woodpecker lift. It's a expensive setup however, regardless of which way you go. If that's too much then I would go with a simple fence from Rockler and add just attach any supplemental fence to it. The other expensive ones (kreg, Jessem, etc) just seemed to similar to the Rockler set up to justify paying the extra amount. Quote
rodger. Posted January 6, 2016 Report Posted January 6, 2016 On 05/01/2016 at 1:58 PM, bigarm said: I am also considering a cast iron extension for my Delta 36-725. I can find a couple of different ones. One is the MLCS and U turn lift which is a little cheaper. The other seems to be a Bench Dog with an Incra Master R Lift II which would be a little more expensive. The U Turn says it has 3" of lift. I can't find the amount for the Incra, but it says it can do above table bit changes. The Incra can work with the Porter Cable 7518 or the Milwaukee 5625. The U Turn specifically mentions the PC, but does not mention the Milwaukee. Any info on either of these? I bought one from general tools, and added a jessem insert. I am not a big fan of the router lift, as I find the bit changes on a TS wing quite painless. Don't worry too much about the holes lining up perfectly, cast iron can be drilled pretty easily to accommodate your saw. Quote
Robby W Posted January 7, 2016 Report Posted January 7, 2016 I have the Milwaukee 5625. Mine is installed in a Jessem Mast-R-Lifter in a table I built as the left wing of my table saw. I use the Rockler Pro fence. I love the Milwaukee router. It has an excellent speed control, the collects grip and release well and it powers all of my bits from 1/8" to 3 1/2" without any problem. I also have a Porter-Cable 518 industrial router and prefer the Milwaukee. This combination works well for me. If you are on a budget, but still want a big router, the Milwaukee 5625 router comes with a fixed base that can be mounted in a router table and adjusted from above with a supplied wrench. You jut have to drill a hole for access to the adjuster. Mount the 5625 on a Jessem phenolic plate, which is inexpensive and gives you throat inserts, drill the hole for the adjuster wrench and you are good to go. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.