Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Show us your scrubber!

Featured Replies

Anyone have a shop made air scrubber they would like to share?  Thinking about building one, and doing some research.

I built one for my old shop. There was a ceiling hung air conditioning unit that had an air blower before the coil. So,I bought a deep pocket filter and a pre filter that were close to the OD size of the unit and built a box that fit over the air blower and then sized the inside of the box to hold the filters. Quite a few years later the air blower died and I abandoned the whole thing.

 

Front View

 

Side View

 

Very simple, if I remember correctly cost was about a $100.00 Went to the box store and purchased an attic fan and some plywood. Good 20x20 furnace filters on each side. Wired in a wall switch to turn it on. 

 

-Ace-

 

Anyone have air scrubbers that use HEPA filters?  Furnace filters are good for larger particles but I'm concerned about the super fine dust - which is most dangerous. 

My furnace filter is rated better than the HEPA rating on my vacuum cleaner filters. Don't lump them all together like all furnace filters are identical. 

38 minutes ago, ChrisG-Canada said:

Anyone have air scrubbers that use HEPA filters?  Furnace filters are good for larger particles but I'm concerned about the super fine dust - which is most dangerous. 

 

I use 2 3M Filtrete 1250 furnace filters. Not sure what all that means, cost is about 18.00 each. The filter material is very fine like paper. 

-Ace-

 

Years ago I built an air scrubber from some plans I found in a book or magazine. It works pretty well. It's made out of plywood and uses two bathroom (fart fans) vents. I use the 3M Filtrete filters that slide in a track milled in the bottom. I use flexible duct to exhaust the fans away from the input and cause better circulation. I can try and get pictures if anyone is interested.

  • Author
1 hour ago, woodbutcher74 said:

Years ago I built an air scrubber from some plans I found in a book or magazine. It works pretty well. It's made out of plywood and uses two bathroom (fart fans) vents. I use the 3M Filtrete filters that slide in a track milled in the bottom. I use flexible duct to exhaust the fans away from the input and cause better circulation. I can try and get pictures if anyone is interested.

Sure, would like to see.

11 hours ago, Pug said:

Sure, would like to see.

I built this several years ago. I have ducted the exhaust from the fans across the ceiling and down to the floor. This moves the warm air by the ceiling down to the floor and also keeps the fans from pushing the dusty air away from the input. In the picture you can also see the 2'x8' radiant heat panels that I installed.

Dust Scrubber 1.jpg

Dust Scrubber 2.jpg

Dust Scrubber 3.jpg

Dust Scrubber 4.jpg

Why not just buy ambient air cleaner replacement filters from Wynn and make your own blower/box for them? I think the filters that fit my JDS are MERV 15 and $70 for two filters. These filters have a ton of area on them, because they are 2' deep and semi pleated. I think when you work out the true cost, the wynn filters have to be a better buy than furnace filters. Also, it would be a good idea to get one of those electrostatic pre-filters if you can. That sucker kicks butt, and you can keep rinsing it or blowing it out for years to come. I clean my outer static filter every 3-4 weeks, and I got about 10 months out of the internal filter before replacing it. I blew that filter out a handful of times too, but I expect to get about a year per filter bag, which is well worth the $35-40 a year in cost.

 

Ultimately, if you do all the things I just said, you would be better off buying the cleaner for $350 and having a professionally designed and fabricated machine with a remote, warranty, etc, but you might enjoy the build.  

 

I wonder how well the box fans and furnace filters work compared to the purchased units. I assume they work well enough. Marc's recent test with the dylos proved that these units are an important part of the lineup when tackling dust collection and mitigation.

  • Author

I would love to order from Wynn, and have tried many times.  They will not ship to Canada.

I am gonna build a box fan unit for fun, and test it out.  If it sucks, I'll buy a ceilling mounted unit.  It looks like I need to spend about 500 CDN for a decent unit (General Tools).  The others in the usual suspects line up seem to fall short on the quality (Craftex, King), and powermatic is $$$ and not reviewed that highly.  I cant get JET or JDS in my area.

Pug, have you seen the Frank Howarth video on his air filter cart? 

 

An air scrubber on the floor makes no sense to me. Years ago, I made a down draft sanding table in similar fashion using a HVAC fan like he did. The exhaust of clean air blows at floor level kicking up dust that has settled on the floor making air quality worse. I guess you could turn it on and leave the room? However, I run my overhead air scrubber while working and catches the dust while in the air above the machines. 

To make this design work. An exhaust flex pipe out a window or even off the floor would make it better.

 

Thats how I roll.

 

-Ace-

21 hours ago, Pug said:

I would love to order from Wynn, and have tried many times.  They will not ship to Canada.

I am gonna build a box fan unit for fun, and test it out.  If it sucks, I'll buy a ceilling mounted unit.  It looks like I need to spend about 500 CDN for a decent unit (General Tools).  The others in the usual suspects line up seem to fall short on the quality (Craftex, King), and powermatic is $$$ and not reviewed that highly.  I cant get JET or JDS in my area.

It's up to you, but I put up the small King unit (KAC-410) up a couple of months ago and I've been really happy with it. It's intended for smaller spaces, but I've got it in a single garage and it works pretty well. The price was pretty reasonable, right around $200 CAD. I wanted the timer and multiple speeds, plus for me it had to be a ceiling mount or I couldn't fit it in.

 

KAC-410-HR.jpg

  • Author
20 hours ago, -MattK- said:

Pug, have you seen the Frank Howarth video on his air filter cart? 

 

This is pretty nice, but WAY too big for my small shop!

1 hour ago, SawDustB said:

It's up to you, but I put up the small King unit (KAC-410) up a couple of months ago and I've been really happy with it. It's intended for smaller spaces, but I've got it in a single garage and it works pretty well. The price was pretty reasonable, right around $200 CAD. I wanted the timer and multiple speeds, plus for me it had to be a ceiling mount or I couldn't fit it in.

 

KAC-410-HR.jpg

I searched the forums and such looking for opinions on this unit.  What I read (and there were only a few) was mostly negative.  Can you elaborate a bit more on this unit?  The size is right, and so is the price.  I just don't want to go to the effort of buying, wiring, and mounting this unit to have it be of poor design/quality.

I consider this forum a trusted source of info, so if you can speak positively on it, I'll seriously consider getting one.

I searched the forums and such looking for opinions on this unit.  What I read (and there were only a few) was mostly negative.  Can you elaborate a bit more on this unit?  The size is right, and so is the price.  I just don't want to go to the effort of buying, wiring, and mounting this unit to have it be of poor design/quality.

I consider this forum a trusted source of info, so if you can speak positively on it, I'll seriously consider getting one.

I'm happy to answer anything I can. I installed mine about 2 months ago, so I can't really say anything about longevity yet. It came with the chains and hooks for mounting. I put it up behind my garage door opener. It was pretty easy to install.

1edfdeeec130555bb7b22e56129d4afa.jpg

It's got the standard controls and remote, with three speeds and 1, 2, and 4 hour timer settings. It's pretty quiet. I don't find it objectionable to have it run when I'm out there, especially on the lower speeds. It moves a decent amount of air, but I could see it being insufficient if you had a bigger shop. For me in a single car garage, it's just about perfect.

I guess I'm not sure what else I would ask of it. As long as it keeps working as is, I'm happy.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.