Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Ten Degrees of Garden Bench

Featured Replies

  • Popular Post

Wanted to put my newly acquired Hammer A3-31 to use and what better way than to mill some some 8/4 white oak for a garden bench as a gift for some friends?

Plans are from Woodsmith. I coined the thread title because every bevel and miter you see is ten degrees from square, including the crown on the false tenons.

Plans include dowels to strengthen the dadoed leg joinery, and a wood screw under each false tenon secures the seat.

Since different types of exterior finishes require varying levels of maintenance, I opted to leave it unfinished for the recipients. Unfinished white oak should withstand the elements well and requires no maintenance. A wipe on oil finish would need yearly reapplication, but it would be easier to prep for and reapply; whereas Epiphanes marine finish will look great for three or four years but would be more difficult to refinish.

Turns out the recipients consider the bench too nice to sit outside, so oil it is.

Thanks for viewing.

cb4dcf11c14668297aca28800938573d.jpg24143cd3903e6ee4babda55d421c4da0.jpg

I was especially pleased with the glue-up of the seat. The grain renders the glue-line almost invisible.

f2879a66e07999d1e6e6e1c957236085.jpg

Very nice job, Nestor ! You forgot something in your post.....how do you like the Hammer??? Give us some thoughts and maybe a few pics !

 

Very nice job!  Clean and tidy!  Well executed!

  • Author
  • Popular Post

Thanks.

As requested, here's my review of the Hammer.

3a4e19ef127a66fa8c7a86413d4ec570.jpg

1e53dacf562b71c3f2684a967816cef4.jpg

8ed8e17a507e61789bd85208651f036f.jpg

Disclaimer: I've used a planer on only three projects; my previous jointer was bought used and never saw a project after I brought it home and gave it some TLC. IOW, my experience is limited.

The Hammer replaced a Dewalt 735 and a Busy Bee Craftex 8" jointer. I wasn't really looking for the Hammer until one came up for sale on Canadian Woodworking Forum. The seller lost his job shortly after replacing his shop equipment from a fire. It was still on the pallet and packed. I think I got a pretty good deal.

The sale included an extension table, digital gauge for the planer, and mobility "base". It also included the "silent power" helical cutter head with carbide teeth.

The mobility base is basically two wheels and a shaft that mount directly on the jointer and a wheeled tow handle. unfortunately, the setup means one pulls from the front (aka long side). Not ideal for a small shop, so I ended up getting a 900lb base.

Setup was straightforward with a couple of exceptions. Hammer made a video on how to unpack and setup the jointer/ planet, which was helpful.

The digital gauge is a clever setup. It's entirely self-contained with a weighted face that stays level as the crank is turned. It's precisely matched to the change in height of the table with one turn of the crank. There is both a mechanical counter and a dial for fine adjustment. To calibrate, run a piece of wood through and measure the thickness with calipers. Then loosen the housing from the crank and "roll" the gauge until the counter and dial match the measured thickness. You're done.

The fence is somewhat flimsy and seems out of place with the caliber of the rest of the machine. The stops are bolts and locknuts which are a pain to setup. Tightening the locknut throws off the setup and requires repeated loosening, measuring, tightening and remeasuring. Surely there are better ways to do this.

My other quibble is with the table finish. The grind doesn't lend itself to a low friction surface and I found myself struggling to slide stock with push pads. I need to play with different waxes to mitigate this.

Changing from jointer to planer is a snap. Turn two handles a quarter turn, lift and tilt the table, flip the dust shroud up and over, lift and push a lever to engage the rollers and you're ready to go. The lift table needs to be at least 7 1/2 inches away to leave room for the dust shroud in jointer mode, so unless you're about to plane 7 inch thick stock, this will mean some cranking. Some people complain about this, but it doesn't bother me.

Infeed table adjustment is one lever not unlike the Craftex I had. The tables were coplaner from the factory and required no adjustment.

The guard is the Euro type and does not swing away like the North American pork chop guard. It takes a little getting used to since it means a break in one's movement. The guard can be slid entirely out of the way, but it's probably better to learn to get used to it from the outset.

A 220 V , 30A cct is required. Luckily, I was able to add a plug and use an available welding receptacle.

The cutter head is supposed to be quieter. I suppose it is, but it's still loud and with the DC, one still needs hearing protection. The only tear out was on the edge of one board, but it was hard to tell which way the grain direction was anyways, so I don't fault the jointer.

The planer works great, though it grabs the board rather abruptly when compared to the Dewalt. There are claims that boards come out snipe free but that isn't the case. I still witnessed some snipe.

The Hammer powered through every piece of white oak without bogging down, and I was able to work quickly once I got into a rhythm. I also like not having to drag out and set up the planer on my bench.

Overall, I'm very satisfied with my purchase.

ETA, it was nice to send the entire 12 X 36" seat though the jointer after glue-up. I can see this as a major time saver. It also gave me more options when buying wider rough-sawn boards.

Sent from my iPad using Tapatalk

  • Author
Looks pretty sharp ! Sign it and date it !

I thought of it but it felt like I was taking credit for another person's design.

I did suggest to the love birds that if it was going to sit outside, they could carve their names into it. ;-)

Sent from my iPhone using Tapatalk

Thanks.

As requested, here's my review of the Hammer.

3a4e19ef127a66fa8c7a86413d4ec570.jpg

1e53dacf562b71c3f2684a967816cef4.jpg

8ed8e17a507e61789bd85208651f036f.jpg

Disclaimer: I've used a planer on only three projects; my previous jointer was bought used and never saw a project after I brought it home and gave it some TLC. IOW, my experience is limited.

The Hammer replaced a Dewalt 735 and a Busy Bee Craftex 8" jointer. I wasn't really looking for the Hammer until one came up for sale on Canadian Woodworking Forum. The seller lost his job shortly after replacing his shop equipment from a fire. It was still on the pallet and packed. I think I got a pretty good deal.

The sale included an extension table, digital gauge for the planer, and mobility "base". It also included the "silent power" helical cutter head with carbide teeth.

The mobility base is basically two wheels and a shaft that mount directly on the jointer and a wheeled tow handle. unfortunately, the setup means one pulls from the front (aka long side). Not ideal for a small shop, so I ended up getting a 900lb base.

Setup was straightforward with a couple of exceptions. Hammer made a video on how to unpack and setup the jointer/ planet, which was helpful.

The digital gauge is a clever setup. It's entirely self-contained with a weighted face that stays level as the crank is turned. It's precisely matched to the change in height of the table with one turn of the crank. There is both a mechanical counter and a dial for fine adjustment. To calibrate, run a piece of wood through and measure the thickness with calipers. Then loosen the housing from the crank and "roll" the gauge until the counter and dial match the measured thickness. You're done.

The fence is somewhat flimsy and seems out of place with the caliber of the rest of the machine. The stops are bolts and locknuts which are a pain to setup. Tightening the locknut throws off the setup and requires repeated loosening, measuring, tightening and remeasuring. Surely there are better ways to do this.

My other quibble is with the table finish. The grind doesn't lend itself to a low friction surface and I found myself struggling to slide stock with push pads. I need to play with different waxes to mitigate this.

Changing from jointer to planer is a snap. Turn two handles a quarter turn, lift and tilt the table, flip the dust shroud up and over, lift and push a lever to engage the rollers and you're ready to go. The lift table needs to be at least 7 1/2 inches away to leave room for the dust shroud in jointer mode, so unless you're about to plane 7 inch thick stock, this will mean some cranking. Some people complain about this, but it doesn't bother me.

Infeed table adjustment is one lever not unlike the Craftex I had. The tables were coplaner from the factory and required no adjustment.

The guard is the Euro type and does not swing away like the North American pork chop guard. It takes a little getting used to since it means a break in one's movement. The guard can be slid entirely out of the way, but it's probably better to learn to get used to it from the outset.

A 220 V , 30A cct is required. Luckily, I was able to add a plug and use an available welding receptacle.

The cutter head is supposed to be quieter. I suppose it is, but it's still loud and with the DC, one still needs hearing protection. The only tear out was on the edge of one board, but it was hard to tell which way the grain direction was anyways, so I don't fault the jointer.

The planer works great, though it grabs the board rather abruptly when compared to the Dewalt. There are claims that boards come out snipe free but that isn't the case. I still witnessed some snipe.

The Hammer powered through every piece of white oak without bogging down, and I was able to work quickly once I got into a rhythm. I also like not having to drag out and set up the planer on my bench.

Overall, I'm very satisfied with my purchase.

ETA, it was nice to send the entire 12 X 36" seat though the jointer after glue-up. I can see this as a major time saver. It also gave me more options when buying wider rough-sawn boards.

Sent from my iPad using Tapatalk

Sounds like a great machine ! Thanks for the review.

You mention Canadian Woodworking amd Craftex are you from Canada?

Sent from my SM-N910W8 using Tapatalk

  • Author
Sounds like a great machine ! Thanks for the review.

You mention Canadian Woodworking amd Craftex are you from Canada?

Sent from my SM-N910W8 using Tapatalk

Yes. Ontario.

Sent from my iPhone using Tapatalk

15 hours ago, Nestor said:

Overall, I'm very satisfied with my purchase.

 

Thanks for the review. I am looking at this machine for my shop soon. 

23 hours ago, Nestor said:

Turns out the recipients consider the bench too nice to sit outside, so oil it is.

The recipients are right.  

13 minutes ago, Llama said:

Thanks for the review. I am looking at this machine for my shop soon. 

Llama, I'm curious if you are also considering the Jet 12" combination machine? 

1 hour ago, Mark J said:

Llama, I'm curious if you are also considering the Jet 12" combination machine? 

I haven't considered any other combo machine. 

I like how the table tops open flat on my earlier version they angle back in the planer mode and it takes up more room. Having said that I love the machine for the footprint it takes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.