Rex Edgar Posted December 20, 2016 Report Posted December 20, 2016 Is there a difference if one starts jointing the wide or narrow edge of the wood to be squared? I have always started with the narrow edge, but saw a video where the person began with the wide edge. Quote
Tpt life Posted December 20, 2016 Report Posted December 20, 2016 Are you talking X or Y axis? Taper down to the table or turned to the side? Quote
bleedinblue Posted December 20, 2016 Report Posted December 20, 2016 Do you mean the face of the board and the edge of the board? Joint a face first so you can reference that to square the edge. If that's not what you mean, I am stepping back slowly because I don't know! Quote
Rex Edgar Posted December 20, 2016 Author Report Posted December 20, 2016 20 minutes ago, bleedinblue said: Do you mean the face of the board and the edge of the board? Joint a face first so you can reference that to square the edge. If that's not what you mean, I am stepping back slowly because I don't know! That's exactly what I meant, Thank you 23 minutes ago, C Shaffer said: Are you talking X or Y axis? Taper down to the table or turned to the side? What are you referring to? Quote
Tpt life Posted December 20, 2016 Report Posted December 20, 2016 Disregard. He understood, I was in another place. I call the wide a face. Quote
Popular Post gee-dub Posted December 20, 2016 Popular Post Report Posted December 20, 2016 Depending on the dimensions . . . Joint the face or broadest surface first. The 'edge' gives too narrow of a bearing surface to act as a reference for the perpendicular 'face' being milled. The jointer cannot magically create perpendicular faces. You flatten a reference surface and then run that reference surface against the fence to mill the perpendicular surface. Even if I am milling a 4x4 I will joint one surface first, then use that milled surface as my reference surface to create a perpendicular surface. I then plane the opposing 'face' using the jointed 'face' as a reference and then use the jointed 'edge' to rip the opposing edge parallel. Crosscut to length. Make sense? 3 Quote
Ronn W Posted December 20, 2016 Report Posted December 20, 2016 Yep, do the face first. I will often go from there to the thickness planer and and not joint the edge until it is time to rip the piece to width. 2 Quote
sjm1580 Posted December 20, 2016 Report Posted December 20, 2016 So let me ask a follow-up. I have a 6 inch jointer and am about to mill some 8 inch wide maple. I think it would be best to joint the edge first then the face, because I have to put the partially unfinished face on a sled and then take that to my planer? Does that sound like the correct sequence? Quote
drzaius Posted December 20, 2016 Report Posted December 20, 2016 53 minutes ago, sjm1580 said: So let me ask a follow-up. I have a 6 inch jointer and am about to mill some 8 inch wide maple. I think it would be best to joint the edge first then the face, because I have to put the partially unfinished face on a sled and then take that to my planer? Does that sound like the correct sequence? Unless the edge is of substantial thickness (several inches), that won't work. The edge would have to be thick enough to hold the piece perpendicular to the fence when you joint the face. The way to do it is to use the planer sled to flatten 1 face, then use the jointer to joint the edge, registering the flattened face to the jointer fence. Quote
sjm1580 Posted December 20, 2016 Report Posted December 20, 2016 7 minutes ago, drzaius said: Unless the edge is of substantial thickness (several inches), that won't work. The edge would have to be thick enough to hold the piece perpendicular to the fence when you joint the face. The way to do it is to use the planer sled to flatten 1 face, then use the jointer to joint the edge, registering the flattened face to the jointer fence. I am using 6/4 maple so with that thickness you would still start with a sled on the planer? Quote
Janello Posted December 21, 2016 Report Posted December 21, 2016 If you buy a decent hand plane (IE: Smoother or Jack) you can hang the face off the jointer (remove guard if necessary) and hand plane that last 2 inches off [referencing off the flat face that ran through the blades]. In simple terms...buy a hand plane...skip the planer sled idea. It takes an extra 5 minutes with a good plane to take the ledge that didn't run across the jointer blade off. 2 Quote
sjm1580 Posted December 21, 2016 Report Posted December 21, 2016 11 minutes ago, Janello said: If you buy a decent hand plane (IE: Smoother or Jack) you can hang the face off the jointer (remove guard if necessary) and hand plane that last 2 inches off [referencing off the flat face that ran through the blades]. In simple terms...buy a hand plane...skip the planer sled idea. It takes an extra 5 minutes with a good plane to take the ledge that didn't run across the jointer blade off. So would you start off with the face or start with the edge? Looking at an 8 foot 6/4 maple... Thanks! Quote
bleedinblue Posted December 21, 2016 Report Posted December 21, 2016 Without a doubt start with the face. Quote
gee-dub Posted December 21, 2016 Report Posted December 21, 2016 56 minutes ago, sjm1580 said: So would you start off with the face or start with the edge? Looking at an 8 foot 6/4 maple... Thanks! I would still start with the broadest surface so, the 'face'. I would avoid jointing an 8 foot piece of material unless my eventual part was over 90" in length. Crosscut to approximate length first to reduce the influence of irregularities. For example, an 8' piece may show a 1/2" of bow while a 38" piece cut from that may show much less. I always break material down to approximate size before milling. This pretty much happens automatically since the piece of material I want for a certain part is rarely cooperative enough to be at an end/edge location in the material. Ronn W brings up a good point that I failed to include; if you face joint and then plane to approximate thickness you can edge joint while taking grain direction into account. 2 Quote
sjm1580 Posted December 21, 2016 Report Posted December 21, 2016 1 hour ago, Janello said: If you buy a decent hand plane (IE: Smoother or Jack) you can hang the face off the jointer (remove guard if necessary) and hand plane that last 2 inches off [referencing off the flat face that ran through the blades]. In simple terms...buy a hand plane...skip the planer sled idea. It takes an extra 5 minutes with a good plane to take the ledge that didn't run across the jointer blade off. Thanks! Unfortunately (or fortunately) 8 feet will be my finished length on the pieces I am milling so I will just have to take my time and work through it. Thanks for the help! Quote
Tpt life Posted December 21, 2016 Report Posted December 21, 2016 We keep missing apparently. Your edge will never square to a wonky face. You joint the face, then joint the edge *with the jointed face pushed to the fence.* Using a hand plane to finish a wide board does not change that process. Quote
sjm1580 Posted December 21, 2016 Report Posted December 21, 2016 2 minutes ago, C Shaffer said: We keep missing apparently. Your edge will never square to a wonky face. You joint the face, then joint the edge *with the jointed face pushed to the fence.* Using a hand plane to finish a wide board does not change that process. Got it, thanks for the help! Quote
drzaius Posted December 21, 2016 Report Posted December 21, 2016 1 hour ago, Janello said: If you buy a decent hand plane (IE: Smoother or Jack) you can hang the face off the jointer (remove guard if necessary) and hand plane that last 2 inches off [referencing off the flat face that ran through the blades]. In simple terms...buy a hand plane...skip the planer sled idea. It takes an extra 5 minutes with a good plane to take the ledge that didn't run across the jointer blade off. Even better. Quote
sjm1580 Posted December 21, 2016 Report Posted December 21, 2016 1 hour ago, drzaius said: Even better. Can you get by with the higher quality Stanley planer or is it better to just go the Lie Nielson / Lee Valley / Veritas route and cut to the chase? Quote
bleedinblue Posted December 21, 2016 Report Posted December 21, 2016 1 hour ago, sjm1580 said: Can you get by with the higher quality Stanley planer or is it better to just go the Lie Nielson / Lee Valley / Veritas route and cut to the chase? If you can afford it, Lee Valley or Lie Nielsen without a doubt. If you can't afford those, get an old Stanley and learn to tune it up. 1 Quote
Janello Posted December 21, 2016 Report Posted December 21, 2016 I tend to agree with bleedinblue. You know your ready to invest when it makes an impact on the current project. My first hand plane was a Veritas Jack with a 38 degree blade. I picked up a few sheets of cheap micro abrasives to keep it sharp and still use it all the time. Was a great investment. One you certainly won't regret if you stick with woodworking. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.