Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Grain direction question

Featured Replies

So I'm building a bookcase. Because of an issue with the baseboard heaters in my apartment, the bottom of the back legs need to sit back 3" from the wall. I discussed it here:

Wood movement over a heater

I've decided to do a Krenov inspired case. However I decided to do something I've not attempted before - curvey, criss crossed legs (see attached). I was planning on making it from cherry. Just for scale, they are currently 1.5" square. The circle at the crossing point will be a dowel running between the two sets of legs to add to the stability and stop the legs from splaying. I'm planning on using aprons between the four legs.

How should I best orientate the grain in the piece to give me the best strength and stability? Am I setting myself up for failure?

 

BookcaseLegs.jpg

8 minutes ago, krtwood said:

I would do a bent lamination.

Heat will soften the glue. I'd reccomend epoxy.

Honestly, that says steam bend to me. Bent lam might give a better consistency I guess. Hey @RichardA, why assume a bent lam needs heat?

Never mind...had to chase the link. 

  • Author
1 hour ago, krtwood said:

I would do a bent lamination.

Now that's an idea I hadn't considered. I think steam bending is something I want to try at a later date, but the bent laminations is well within my skill set I just haven't tried it before. For something like this, how thick should the laminations be? 1/8"? or thicker? I don't have a drum sander so I might have to get inventive with the tools I do have.

1 hour ago, C Shaffer said:

Honestly, that says steam bend to me. Bent lam might give a better consistency I guess. Hey @RichardA, why assume a bent lam needs heat?

Never mind...had to chase the link. 

Didn't "need" it, but sounded like it was going to get it.  I just figured that epoxy would hold better around heat. 

  • Author
1 hour ago, AndrewPritchard said:

Now that's an idea I hadn't considered. I think steam bending is something I want to try at a later date, but the bent laminations is well within my skill set I just haven't tried it before. For something like this, how thick should the laminations be? 1/8"? or thicker? I don't have a drum sander so I might have to get inventive with the tools I do have.

Heh - Mark's video on bent laminations has answered those questions :D

 

Is it supposed to be a table with a bookcase on it?  Either way that looks goofy to me. 

If I'm going to assume that one shelf is the only shelf, then I'd say ditch the solid sides and continue the curve structure up the sides of the bookcase.   Lose the double table looking part too, and make the bookcase the same size as the base, so the curves blend into each other nicely.  It'll be some Elven Lord of the Rings looking stuff, but I think it'll be nice. 

 

  • Author
20 minutes ago, Marmotjr said:

Is it supposed to be a table with a bookcase on it?  Either way that looks goofy to me. 

If I'm going to assume that one shelf is the only shelf, then I'd say ditch the solid sides and continue the curve structure up the sides of the bookcase.   Lose the double table looking part too, and make the bookcase the same size as the base, so the curves blend into each other nicely.  It'll be some Elven Lord of the Rings looking stuff, but I think it'll be nice. 

 

It is a bookcase, but the only shelf shown on there will be fixed for rigidity. The others aren't shown.

The double table look is there for two reasons - one it matches another piece of furniture I already have, but mostly because it's going at the end of my couch which doesn't have anywhere to rest a cup of your favorite beverage. I have small kids and anyway I don't like coffee tables. Personal preference.

Then I'd either ditch the cool base, and make it a cabinet that has a bookcase on top of it, or ditch the solid sided bookcase for a bookcase with fixed shelves that are supported by the same funky cool legs on the base.  You could do bent laminations to make a series of X's to support multiple shelves. 

I dunno, kinda a tough call, given the multitude of demands you are asking of it. 

  • Author
1 minute ago, Marmotjr said:

Then I'd either ditch the cool base, and make it a cabinet that has a bookcase on top of it, or ditch the solid sided bookcase for a bookcase with fixed shelves that are supported by the same funky cool legs on the base.  You could do bent laminations to make a series of X's to support multiple shelves. 

I dunno, kinda a tough call, given the multitude of demands you are asking of it. 

As I mentioned in my original post, there's a couple of reasons why I started down the route with this design - most notably the 4" high and 3" deep baseboard heater running round the wall of my living room.

1 minute ago, AndrewPritchard said:

As I mentioned in my original post, there's a couple of reasons why I started down the route with this design - most notably the 4" high and 3" deep baseboard heater running round the wall of my living room.

Right, I got that, that's why the rear legs stop short and look like it wants to tip over, but won't cause it's up against a wall.   You could build a cabinet to wrap around the baseboard, giving it enough clearance, or you could continue the legs up the sides. 

It looks like you started building a camaro and finished it with an econoline van. 

It looks like the base is too narrow and thaty ou might have a problem with it tipping, especially if the bookcase is heavily loaded.  In addition, with the bookcase set back almost against the wall and the legs against the wall pull out a few inches, you are loading the table part off center which will encourage it to tip towards the wall.

  • Author
1 minute ago, Ronn W said:

It looks like the base is too narrow and thaty ou might have a problem with it tipping, especially if the bookcase is heavily loaded.  In addition, with the bookcase set back almost against the wall and the legs against the wall pull out a few inches, you are loading the table part off center which will encourage it to tip towards the wall.

Surely tipping towards the wall won't be a problem given that there's a wall in the way. Or am I missing something?

I have a preference for furniture to to touch the wall.  If it does lean aginst the walll, all the weight will be on 2 legs.

  • Author
28 minutes ago, Marmotjr said:

Right, I got that, that's why the rear legs stop short and look like it wants to tip over, but won't cause it's up against a wall.   You could build a cabinet to wrap around the baseboard, giving it enough clearance, or you could continue the legs up the sides. 

It looks like you started building a camaro and finished it with an econoline van. 

The leg position is exactly designed to circumvent my landlord's rather awkward method of heating my apartment. In fact the original discussion was around how the wood might react to being in such close proximity to a heater or indeed if that might cause other issues. Electric heating elements are supposed to have good air circulation around them otherwise they over heat and potentially catch fire.

Yes, I Know, I have baseboard heating for the identical reason.  Landlord just installed a new boiler in the basement in the fall.  I feel your pain.

I'm just saying you're switching styles halfway through the piece.  Pick one, and work around/with the baseboard as needed. 

  • Author
3 minutes ago, Ronn W said:

I have a preference for furniture to to touch the wall.  If it does lean aginst the walll, all the weight will be on 2 legs.

Again, this is why I've gone down the route of crossed legs, rather than just straight legs.

I don't even know if this thing will get built. I'm the kind of person that if I get an idea for a design in my head and I don't put it out on paper and talk about the design elements, it distracts me from other more important ideas and work

  • Author
2 minutes ago, wtnhighlander said:

Back to the curvy legs, I almost suggested bent lamination before, but didn't, because it seemed that method would leave the most visible part of the legs looking like plywood edges. Certainly, it is the strongest method, but maybe not the prettiest.

 

I was considering the plywood edge problem earlier and wondered if putting a form of edge banding on there would work. Would it survive the seasonal shifts?

  • Author
3 minutes ago, Marmotjr said:

Yes, I Know, I have baseboard heating for the identical reason.  Landlord just installed a new boiler in the basement in the fall.  I feel your pain.

I'm just saying you're switching styles halfway through the piece.  Pick one, and work around/with the baseboard as needed. 

The ideas for the top are in no way fixed either (apart from the coffee cup ledge. I still want that.). Someone in the other thread had suggested a Krenov approach to the heat problems, and hence the rabbit hole I'm currently going down.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.