Recommended Posts

Posted

Well finally got some time to do some real woodworking so I figured I should knock out this project first to help with the little ones.

 

So going off Marc's video.

 

Wood is 4/4 pecan

 

562d05836f93b9cfba1539d43c5318b9.jpg

 

caeeb0dd5ae30167fdaecf256f6c9c74.jpg

 

Got all the wood laid out and marked and rough cut to length.

 

Next going to thickness to rough width and let it sit for a few more days.

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Posted
5 minutes ago, Lester Burnham said:

Is there a good rule of thumb for this part? I know one should let things settle and see what's what after a little while when resawing but is there similar issue planning something down to .75" or .5" from say 1" ?

I am sure others will chime in on this one @Eric & @TIODS & @wdwerker with a better answer ... however I have always heard/read you rough it all down to something close .. then let it sit for a day or so to let all the movement happen if you release some stress on the wood or vice versa ... then final plane/joint and you should be decently good to go after that.

The only reason I am splitting the 2 up is because of lack of time on my side over the weekend. Normally I would do both joint / plane to rough measurements then let sit and come back in a day or 2 to finish milling to final.

Also, in the mean time I did order a drawing bow from lee valley to help with the arcs on some of these pieces. Sure I could have made my own, but the low cost of this made it not worth the extra time I would lose screwing with that over actually getting to work on the project.

  • 2 weeks later...
Posted

Got everything milled. A slow week of slowly milling but gotta do what ya gotta do I guess.

 

169b45dcf9cf0409c1c6c63838dba8ef.jpg

 

I like the grain .. call me crazy haha

 

081401b8579e32f3f556e0e20190b88c.jpg

 

 

Hopefully tomorrow or Thursday I'll get to finalize all my pieces and draw it all out to get some good grain for my pieces.

 

Get to bust out all my new Epstein tools to use on their first project too!

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Posted
On 2017-6-12 at 1:44 PM, bushwacked said:

I am sure others will chime in on this one @Eric & @TIODS & @wdwerker with a better answer ... however I have always heard/read you rough it all down to something close .. then let it sit for a day or so to let all the movement happen if you release some stress on the wood or vice versa ... then final plane/joint and you should be decently good to go after that.

The only reason I am splitting the 2 up is because of lack of time on my side over the weekend. Normally I would do both joint / plane to rough measurements then let sit and come back in a day or 2 to finish milling to final.

Also, in the mean time I did order a drawing bow from lee valley to help with the arcs on some of these pieces. Sure I could have made my own, but the low cost of this made it not worth the extra time I would lose screwing with that over actually getting to work on the project.

I usually mill to 1/16th over, let it acclimate, and then "remill", which is pretty quick, as it's so close to final dimension.

  • Like 1
Posted
8 minutes ago, wdwerker said:

I usually mill around 1/16 over, let it acclimate, then dress on the drum sander. Absolutely no risk of tearout like a planer can do.

one day i hope to have a drum sander ... but that is far down on the list of tools I need to buy :( 

Posted
On 2017-6-21 at 8:50 AM, bushwacked said:

1/16th over ... ok I left mine a little heavier as I was not sure how much I would actually need to get back to good. is 1/16 normally good enough or have you ever hit any issues with it?

I've never had an issue - seems to be plenty of meat for final dimensioning.

Posted

I need to buy one of those drawing bows the next time LV has free shipping.  I know they're easy enough to build, but I never take the time to build a reusable one and always just hack something together.

Looking good, if the stars align and the wife allows I'm going to get started on a pair of these tomorrow. 

Posted

Eric's post, should be on everyone's list of first things to do....Read the post, then begin your work.  Yup, it'll get read, but most will just do, then complain.  Oh well. Be smart or be twisted.

Posted

Eric's point about joinery is a good one - i try final mill and cut the joinery as close to glue up as I can, which is almost always the same session (unless it's a complex glue up with multiple stages).

Posted

Dang Eric and his amazingly well answered posts. So much good info there!! I try to do my best to do everything mentioned it. Although this project final milling and joints are not going to get cut at same time.

 

56a1032dae5b219a8ec696afe8907c45.jpg

 

Templates getting cut out and finished.

 

dbd5a2c7af92c0d60d58c5dd7d7c96a1.jpg

 

Cutout on bandsaw and now to route final curve.

 

 

47272ecd9c037434babff8a5e2e395de.jpg

 

Not sure what happened but almost my last board had a blow out. It sucked. No idea why but it happened. Guess I'll just put it on the bottom and hopefully no one will notice haha.

 

f8ca9965929418dbe1eb821cbb63d814.jpg

 

Cutting the leg angles. From 4" to 2"

 

6786bea0954b3cdc7da1ae8458a7e183.jpg

 

Everything marked out. Just test lining a side up to make sure my marks were at least correct and lined up with everything else.

 

 

 

Sent from my iPhone using Tapatalk

Posted
3 minutes ago, bushwacked said:

Dang Eric and his amazingly well answered posts. So much good info there!! I try to do my best to do everything mentioned it. Although this project final milling and joints are not going to get cut at same time.

 

56a1032dae5b219a8ec696afe8907c45.jpg

 

Templates getting cut out and finished.

 

dbd5a2c7af92c0d60d58c5dd7d7c96a1.jpg

 

Cutout on bandsaw and now to route final curve.

 

 

47272ecd9c037434babff8a5e2e395de.jpg

 

Not sure what happened but almost my last board had a blow out. It sucked. No idea why but it happened. Guess I'll just put it on the bottom and hopefully no one will notice haha.

 

f8ca9965929418dbe1eb821cbb63d814.jpg

 

Cutting the leg angles. From 4" to 2"

 

6786bea0954b3cdc7da1ae8458a7e183.jpg

 

Everything marked out. Just test lining a side up to make sure my marks were at least correct and lined up with everything else.

 

 

 

Sent from my iPhone using Tapatalk

Looking good!

Posted

Not too much work. Finished marking off all the other 2 legs. Had a chance to kind of get an idea of what it will look like ...

 

eb0776a68fa4c6a50220065c30c64640.jpg

9be4c36d2a434315047829e7492966dc.jpg

 

No joints yet just laying them on each other.

 

7b4b5515d80b33cde5bbffeda50add9d.jpg

Worried about the inner joints that are not on the edge and I'll have to reference off a makeshift fence or something. Hopefully that doesn't go bad lol.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

Domino or router? I drilled 8 million dowel holes, took forever.

Just don't forgot, one of the braces on the bottom is further away from the inside than the other. If memory serves me correct it's the back one where there aren't any braces for the platform.

 

 

  • 3 weeks later...
Posted
Did you have as many misplaced dominos as me?  I'm building two of these simultaneously and apparently got confused in a couple places, lol.  

 

Haha almost. The removable sides almost got me a couple times. Those dang drill holes and threaded insert got me though. This is now a permanent structure and not break down haha

 

 

 

 

a0adbb12910bf796b6eff966eec571ae.jpg

 

There's my boo boo

 

bee9520bdbbad79b4dcb78e05198c70d.jpg

 

The rubber non stick mats have been amazing. Cut dominos on them without anything moving. It's been great using it.

 

dda4b8e5c3698563719d59182223bb55.jpg

 

Dry fit. Glad everything lined up after my drill disaster

 

 

 

Sent from my iPhone using Tapatalk

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 56 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined