Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Kitchen Helper

Featured Replies

Well finally got some time to do some real woodworking so I figured I should knock out this project first to help with the little ones.

 

So going off Marc's video.

 

Wood is 4/4 pecan

 

562d05836f93b9cfba1539d43c5318b9.jpg

 

caeeb0dd5ae30167fdaecf256f6c9c74.jpg

 

Got all the wood laid out and marked and rough cut to length.

 

Next going to thickness to rough width and let it sit for a few more days.

 

 

Sent from my iPhone using Tapatalk

  • Author
5 minutes ago, Lester Burnham said:

Is there a good rule of thumb for this part? I know one should let things settle and see what's what after a little while when resawing but is there similar issue planning something down to .75" or .5" from say 1" ?

I am sure others will chime in on this one @Eric & @TIODS & @wdwerker with a better answer ... however I have always heard/read you rough it all down to something close .. then let it sit for a day or so to let all the movement happen if you release some stress on the wood or vice versa ... then final plane/joint and you should be decently good to go after that.

The only reason I am splitting the 2 up is because of lack of time on my side over the weekend. Normally I would do both joint / plane to rough measurements then let sit and come back in a day or 2 to finish milling to final.

Also, in the mean time I did order a drawing bow from lee valley to help with the arcs on some of these pieces. Sure I could have made my own, but the low cost of this made it not worth the extra time I would lose screwing with that over actually getting to work on the project.

  • 2 weeks later...
  • Author

Got everything milled. A slow week of slowly milling but gotta do what ya gotta do I guess.

 

169b45dcf9cf0409c1c6c63838dba8ef.jpg

 

I like the grain .. call me crazy haha

 

081401b8579e32f3f556e0e20190b88c.jpg

 

 

Hopefully tomorrow or Thursday I'll get to finalize all my pieces and draw it all out to get some good grain for my pieces.

 

Get to bust out all my new Epstein tools to use on their first project too! [emoji106]

 

 

Sent from my iPhone using Tapatalk

On 2017-6-12 at 1:44 PM, bushwacked said:

I am sure others will chime in on this one @Eric & @TIODS & @wdwerker with a better answer ... however I have always heard/read you rough it all down to something close .. then let it sit for a day or so to let all the movement happen if you release some stress on the wood or vice versa ... then final plane/joint and you should be decently good to go after that.

The only reason I am splitting the 2 up is because of lack of time on my side over the weekend. Normally I would do both joint / plane to rough measurements then let sit and come back in a day or 2 to finish milling to final.

Also, in the mean time I did order a drawing bow from lee valley to help with the arcs on some of these pieces. Sure I could have made my own, but the low cost of this made it not worth the extra time I would lose screwing with that over actually getting to work on the project.

I usually mill to 1/16th over, let it acclimate, and then "remill", which is pretty quick, as it's so close to final dimension.

  • Author

1/16th over ... ok I left mine a little heavier as I was not sure how much I would actually need to get back to good. is 1/16 normally good enough or have you ever hit any issues with it?

I usually mill around 1/16 over, let it acclimate, then dress on the drum sander. Absolutely no risk of tearout like a planer can do.

  • Author
8 minutes ago, wdwerker said:

I usually mill around 1/16 over, let it acclimate, then dress on the drum sander. Absolutely no risk of tearout like a planer can do.

one day i hope to have a drum sander ... but that is far down on the list of tools I need to buy :( 

  • Author

65d0574a0e56b3a27715fd79a5631780.jpg

 

Ripped and cut to final sizing.

 

c9d769ec616d80d1c0c50e0fa9d88200.jpg

 

c2773bb0f9d63959ec9de53f2d08bf08.jpg

 

Yaaaay for new tools. All my stuff helping me layout what I need.

 

 

 

 

Sent from my iPhone using Tapatalk

On 2017-6-21 at 8:50 AM, bushwacked said:

1/16th over ... ok I left mine a little heavier as I was not sure how much I would actually need to get back to good. is 1/16 normally good enough or have you ever hit any issues with it?

I've never had an issue - seems to be plenty of meat for final dimensioning.

I need to buy one of those drawing bows the next time LV has free shipping.  I know they're easy enough to build, but I never take the time to build a reusable one and always just hack something together.

Looking good, if the stars align and the wife allows I'm going to get started on a pair of these tomorrow. 

  • Popular Post

Re: milling in stages...

There are too many variables to give a definitive protocol: quality of wood and the drying process it underwent (the drying process is the most critical...air dried lumber will require much more care and attention than kiln dried), current MC of the wood vs. MC of your environment, species, how much material you're removing, whether or not you're able to mill equal amounts from both sides - and the X factor...some boards are simply more ornery than others.

The general idea of milling in stages is - because there is a good chance the MC inside the board is slightly different from the MC on the outside of a board - when you initially mill you will expose fresh material with a possibly higher (or in rare cases - lower) MC, which needs to now acclimate.  And if it is going to move, you want this to happen at a stage where you still have enough thickness to mill again back to dead flat.

The more material you're removing, the more likely milling in stages will be necessary.  If you're going from rough to 3/4" or 5/8" I would absolutely mill in stages because you're removing a ton of material.  If you're starting with S3S material and only going to 3/4", I wouldn't worry about it (you don't really have a choice anyway).  I think milling down to about 1/16" over final thickness is a good rule of thumb unless you're working with some especially troublesome boards, in which case you should probably leave yourself 1/8" or so.  If you find that you need more than that, you should probably relegate those boards to the smoker stash...because they suck.

Also, the thicker the board, the less critical milling in stages becomes.  8/4 and thicker is much more capable of holding itself in flat simply because there is more meat to resist the potential movement.  (I still mill thick material in stages because it's best practice and a project takes as long as it takes...but technically it's not as important as when working with 4/4 or thinner).

It's not always necessary...some boards will just stay flat...but you never know which ones will cooperate and which ones won't until you do the milling.  Rift and QS boards are less likely to move but they're not impervious; flat sawn boards will be more likely to move.

So milling in stages is simply best practice even though it will often seem like a waste of time.  Milling is a critical stage (IMO the most critical stage) of any project...because if you're starting the build with cupped, bowed or twisted boards, your joinery is gonna suck and you might as well just burn the project from the get-go.

Stickering and stacking your boards after milling and during the entire build is just as important (if not more important) than milling in stages.  Once your boards reach equilibrium, they need to stay that way...or they WILL move.  Laying a part flat on a surface without stickers is a great way to screw yourself.  My parts are ALWAYS stickered throughout a build unless I am actively working with that part.  I'll often even keep a panel stickered as I'm working with it - if the task at hand allows - since panels are the most susceptible to warping...and it can happen quickly...as in hours.  And once it warps, there's no going back.  I always LOL when people ask if they can introduce steam or lay a board out in the sun or some other "clever" solution.  Nope, you're screwed.  Should have treated the board properly from the start.  An ounce of prevention is worth a pound of cure.

It's also best practice to do the joinery immediately after your final milling.  The same day is best but not always possible, obviously.  But try to plan your builds accordingly.  Once the joinery is cut you can basically leave the parts stacked and stickered indefinitely, because if they move a little bit afterward, the joints should pull the parts back into shape.  But cutting joinery in warped boards is an exercise in futility.

Eric's post, should be on everyone's list of first things to do....Read the post, then begin your work.  Yup, it'll get read, but most will just do, then complain.  Oh well. Be smart or be twisted.

Eric's point about joinery is a good one - i try final mill and cut the joinery as close to glue up as I can, which is almost always the same session (unless it's a complex glue up with multiple stages).

  • Author

Dang Eric and his amazingly well answered posts. So much good info there!! I try to do my best to do everything mentioned it. Although this project final milling and joints are not going to get cut at same time.

 

56a1032dae5b219a8ec696afe8907c45.jpg

 

Templates getting cut out and finished.

 

dbd5a2c7af92c0d60d58c5dd7d7c96a1.jpg

 

Cutout on bandsaw and now to route final curve.

 

 

47272ecd9c037434babff8a5e2e395de.jpg

 

Not sure what happened but almost my last board had a blow out. It sucked. No idea why but it happened. Guess I'll just put it on the bottom and hopefully no one will notice haha.

 

f8ca9965929418dbe1eb821cbb63d814.jpg

 

Cutting the leg angles. From 4" to 2"

 

6786bea0954b3cdc7da1ae8458a7e183.jpg

 

Everything marked out. Just test lining a side up to make sure my marks were at least correct and lined up with everything else.

 

 

 

Sent from my iPhone using Tapatalk

3 minutes ago, bushwacked said:

Dang Eric and his amazingly well answered posts. So much good info there!! I try to do my best to do everything mentioned it. Although this project final milling and joints are not going to get cut at same time.

 

56a1032dae5b219a8ec696afe8907c45.jpg

 

Templates getting cut out and finished.

 

dbd5a2c7af92c0d60d58c5dd7d7c96a1.jpg

 

Cutout on bandsaw and now to route final curve.

 

 

47272ecd9c037434babff8a5e2e395de.jpg

 

Not sure what happened but almost my last board had a blow out. It sucked. No idea why but it happened. Guess I'll just put it on the bottom and hopefully no one will notice haha.

 

f8ca9965929418dbe1eb821cbb63d814.jpg

 

Cutting the leg angles. From 4" to 2"

 

6786bea0954b3cdc7da1ae8458a7e183.jpg

 

Everything marked out. Just test lining a side up to make sure my marks were at least correct and lined up with everything else.

 

 

 

Sent from my iPhone using Tapatalk

Looking good!

  • Author

Not too much work. Finished marking off all the other 2 legs. Had a chance to kind of get an idea of what it will look like ...

 

eb0776a68fa4c6a50220065c30c64640.jpg

9be4c36d2a434315047829e7492966dc.jpg

 

No joints yet just laying them on each other.

 

7b4b5515d80b33cde5bbffeda50add9d.jpg

Worried about the inner joints that are not on the edge and I'll have to reference off a makeshift fence or something. Hopefully that doesn't go bad lol.

 

 

Sent from my iPhone using Tapatalk

Domino or router? I drilled 8 million dowel holes, took forever.

Just don't forgot, one of the braces on the bottom is further away from the inside than the other. If memory serves me correct it's the back one where there aren't any braces for the platform.

 

 

  • 3 weeks later...

Did you have as many misplaced dominos as me?  I'm building two of these simultaneously and apparently got confused in a couple places, lol.  

  • Author
Did you have as many misplaced dominos as me?  I'm building two of these simultaneously and apparently got confused in a couple places, lol.  

 

Haha almost. The removable sides almost got me a couple times. Those dang drill holes and threaded insert got me though. This is now a permanent structure and not break down haha

 

 

 

 

a0adbb12910bf796b6eff966eec571ae.jpg

 

There's my boo boo [emoji17]

 

bee9520bdbbad79b4dcb78e05198c70d.jpg

 

The rubber non stick mats have been amazing. Cut dominos on them without anything moving. It's been great using it.

 

dda4b8e5c3698563719d59182223bb55.jpg

 

Dry fit. Glad everything lined up after my drill disaster [emoji106]

 

 

 

Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.