Recommended Posts

Posted
 

I am a beginner in basic woodworking. I bought the Craftsman fixed-based router + table for DIY home projects. I am in the process of getting familiar with the router/table operation + safety rules. I have the following questions.

1. Generally, how high does the router bit need to be positioned with respect to the stock? For example, in the picture below I have a 3/4'' block and am using a 1/2'' cove bit. Where should I set the bit? Are there any rules/tips guide? I understand that the bit needs to be positioned between the gap in the fence.

2. The user manual advises multi-pass routing with cut depth being 1/8'' max/pass. Does this mean that when I align the router fence it should only expose 1/8'' of the bit? The depth is in the X (lateral) instead of the Y (vertical) direction?

3. There is a guard on the router table. During operation, do I flip the guard up or leave it on (for safety) and slide the stock through it using push pad/stick? For example, in table saws the guard should always be present for safety. I have been looking at a bunch of YouTube videos, and all of the router tables don't seem to have a guard.

UGTBW.jpg

uO5OE.jpg

Posted

With the bit shown, you would not use the fence, but rely on the bearing to guide the stock against. So you would start with the bit low, and raise it by 1/8" after each pass until the desired cut is achieved. The "guard" on some router table fences is more for dust collection that finger protection. I can't tell if yours has a vacuum port or not.

Having said all that, the most dangerous mistake I see made with a router (in or out of a table) is cutting the wrong direction. Look at the bit. The cutting edges of the bit should turn inti the wood, AGAINST the direction of feed. This means that in the table, with the stock between you and the bit, you feed the stock right to left. Feeding the wrong way usually turns the stock into a missile.

  • Like 1
Posted

 

On 9/22/2017 at 4:57 PM, wtnhighlander said:

Having said all that, the most dangerous mistake I see made with a router (in or out of a table) is cutting the wrong direction. Look at the bit. The cutting edges of the bit should turn inti the wood, AGAINST the direction of feed. This means that in the table, with the stock between you and the bit, you feed the stock right to left. Feeding the wrong way usually turns the stock into a missile.

 

To add to what Ross said and maybe to clarify a bit...you never run your stock between the bit and fence (for profiles).  If you ever do, you'll find out why.  Don't try it.

  • Like 2
  • 2 weeks later...
Posted
On 9/22/2017 at 5:57 PM, wtnhighlander said:

With the bit shown, you would not use the fence, but rely on the bearing to guide the stock against. So you would start with the bit low, and raise it by 1/8" after each pass until the desired cut is achieved. The "guard" on some router table fences is more for dust collection that finger protection. I can't tell if yours has a vacuum port or not.

Having said all that, the most dangerous mistake I see made with a router (in or out of a table) is cutting the wrong direction. Look at the bit. The cutting edges of the bit should turn inti the wood, AGAINST the direction of feed. This means that in the table, with the stock between you and the bit, you feed the stock right to left. Feeding the wrong way usually turns the stock into a missile.

 

9 hours ago, derekcohen said:

I would set the fence to allow for a 1/8" cut, then move it back for progressive 1/8" cuts, until the last cut is against the bearing.

Regards from Perth

Derek

So ... do people prefer to (a) raise the bit incrementally or (b) adjust the fence & cutting depth incrementally? Or is there a dependency of some sort re the chosen technique?

Posted
7 minutes ago, collinb said:

 

So ... do people prefer to (a) raise the bit incrementally or (b) adjust the fence & cutting depth incrementally? Or is there a dependency of some sort re the chosen technique?

Depends on the profile. Raising some profiles will lose some round or cove. 

Posted

If you're not hogging out too much material, first make sure your material is a little wider than you need, that gives you room to trim the profile on the table saw once you've routed. After routing the piece, trim it on the table saw, re-run the profile and you will have a nice clean smooth cut,  removing chatter-chipout or burns. Think of it like ripping a board on a table saw, then moving the fence in just a hair and re-run that board, to get that nice clean super edge. 

For setting up the router fence, I use a straight edge to line up the fence with the bearing and combination square to square the fence to the miter slide track in the table. 

Also, you can change bearing sizes to achieve different depths of cut if you choose not to use the fence for doing that. 

 

-Ace- 

Posted

As usual, I'll grab the low hanging fruit.

I started with that router table.  It is better than nothing and served me perfectly OK for a few years.  Even as a beginner though, I am pretty sure I didn't make a single cut with that silly guard on.  As with a table saw, I find guards like that just get in the way of push sticks/pads and visibility, inherently making the operation LESS safe. 

Posted
16 hours ago, collinb said:

 

So ... do people prefer to (a) raise the bit incrementally or (b) adjust the fence & cutting depth incrementally? Or is there a dependency of some sort re the chosen technique?

Either method will get you there depending on profile.  Folks without a lift will have a more involved process to unlock the motor, raise the bit, lock the motor, make a pass, unlock the motor, raise the bit, lock the motor, make a pass, etc.  So, if I didn't have a lift I would start with the fence only allowing about 1/8" of cut and step the fence backward for a sequence of cuts ending with a very light cut even though the bit is bearing guided.

Posted
16 hours ago, C Shaffer said:

Depends on the profile. Raising some profiles will lose some round or cove. 

Ah, yes. For some of those bits with a complex profiles.

 

15 hours ago, AceHoleInOne said:

If you're not hogging out too much material, first make sure your material is a little wider than you need, that gives you room to trim the profile on the table saw once you've routed. After routing the piece, trim it on the table saw, re-run the profile and you will have a nice clean smooth cut,  removing chatter-chipout or burns. Think of it like ripping a board on a table saw, then moving the fence in just a hair and re-run that board, to get that nice clean super edge. 

For setting up the router fence, I use a straight edge to line up the fence with the bearing and combination square to square the fence to the miter slide track in the table. 

Also, you can change bearing sizes to achieve different depths of cut if you choose not to use the fence for doing that. 

 

-Ace- 

I understand the process. It was cause for the alternatives that had me questioning for a minute. @C Shaffer answered that.

I've generally worked into the bit rather than raising the bit into the wood. Except for complex profiles it's apparently 6 of 1 ...

Posted
3 hours ago, collinb said:

Ah, yes. For some of those bits with a complex profiles.

 

I understand the process. It was cause for the alternatives that had me questioning for a minute. @C Shaffer answered that.

I've generally worked into the bit rather than raising the bit into the wood. Except for complex profiles it's apparently 6 of 1 ...

10-4

 

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 33 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined