sunadmin Posted October 26, 2017 Report Posted October 26, 2017 I'm working on restoring some windows in my house and am making a new bottom rail. I have everything else in place but one last component is putting the orig profile on the piece. It looks like a standard bevel of some sort but I'm not having any luck solving the puzzle as to which one it could be. I cross sectioned a piece so i could capture the profile as best I could. Quote
drzaius Posted October 26, 2017 Report Posted October 26, 2017 The tricky part is the bevel. If you can't find a router bit with a close enough angle, then you could do the bevel with a dado stack & a jig to hold the piece at just the right angle as you run it through. Then finish the top corner to 90* on the table saw. Quote
RichardA Posted October 26, 2017 Report Posted October 26, 2017 You might be able to do that profile, using two router bits... The top one looks like the angle for shaker cabinets, and the lower one is not much more than a rabbet. Quote
sunadmin Posted October 26, 2017 Author Report Posted October 26, 2017 Ive looked at that but no matter how I try to configure it the bottom lip will be taken off. The angle looks to be about 20 degrees-ish. Quote
RichardA Posted October 26, 2017 Report Posted October 26, 2017 One other option, again it being in two different passes. A 22 1/2* chamfer bit for the top and just a rabbet for the bottom angle. Quote
drzaius Posted October 26, 2017 Report Posted October 26, 2017 2 minutes ago, sunadmin said: Ive looked at that but no matter how I try to configure it the bottom lip will be taken off. That's why you use a dado stack & jig. Set the stack to the same width as the beveled part. That will leave a sharp protrusion at the corner that you can cut off with the table saw. Quote
Woodenskye Posted October 26, 2017 Report Posted October 26, 2017 Do you have any specialty or high end millwork shops in your area? They may have in stock or the tooling to knock it out in a few minutes. It looks to me like you could use a chamfer bit to make the bevel. I'm just not sure if raising the bit high enough to leave the small section would be possible or safe. Maybe the other option is doing in 2 pieces and laminating them. Quote
sunadmin Posted October 26, 2017 Author Report Posted October 26, 2017 It's for a window sash bottom rail so I'm not really interested in doing it in multiple pieces. Quote
sunadmin Posted October 26, 2017 Author Report Posted October 26, 2017 2 minutes ago, Woodenskye said: Do you have any specialty or high end millwork shops in your area? They may have in stock or the tooling to knock it out in a few minutes. It looks to me like you could use a chamfer bit to make the bevel. I'm just not sure if raising the bit high enough to leave the small section would be possible or safe. Maybe the other option is doing in 2 pieces and laminating them. It's part of a custom made bottom rail that is 100% custom. There were about 20 steps and this is the last one. Unless someone had the exact router bit a millwork shop most likely wouldn't be able to help. Quote
Immortan D Posted October 26, 2017 Report Posted October 26, 2017 Mathias uses a tilting router lift to make custom moldings. He has several videos on the subject, this is one of them: Quote
wdwerker Posted October 26, 2017 Report Posted October 26, 2017 Sounds like it’s time for a custom router bit or shaper cutter . One of my suppliers has a insert head on a shaper and a profile grinder to make knives. They have made matching moldings for me a few times. Quote
Ronn W Posted October 26, 2017 Report Posted October 26, 2017 Dado stack tilted - but you will need to make a home made zero clearance insert. MIght be worth the effort if you have several to do. Cut the bevel first and the do the rabbet. 1 Quote
drzaius Posted October 26, 2017 Report Posted October 26, 2017 6 minutes ago, Ronn W said: Dado stack tilted - but you will need to make a home made zero clearance insert. MIght be worth the effort if you have several to do. Cut the bevel first and the do the rabbet. Yes this, tilt the dado or tilt the piece. This would not be hard to do. The entire profile could be done in 5 passes max, with just a dado stack & a rip blade (preferable flat top grind). Quote
Immortan D Posted October 26, 2017 Report Posted October 26, 2017 Maybe a bit for raising panels could work, like this one: https://www.yonicotools.com/products/panel-raiser-router-bit-vertical-bevel-design-1-2-shank-yonico-12144 A shorter one, from Rockler: http://www.rockler.com/raised-panel-router-bit-straight Quote
sunadmin Posted October 26, 2017 Author Report Posted October 26, 2017 4 hours ago, wdwerker said: Sounds like it’s time for a custom router bit or shaper cutter . One of my suppliers has a insert head on a shaper and a profile grinder to make knives. They have made matching moldings for me a few times. Could you PM or post the info? Quote
wdwerker Posted October 26, 2017 Report Posted October 26, 2017 Shipping moldings from Ga would be prohibitive. Quote
Tom King Posted October 26, 2017 Report Posted October 26, 2017 A custom bit to cut that profile would be about $250, in carbide. I don't know if anyone cuts plain steel ones any more. I used to get custom router bits from Whiteside, but they've grown so much that they can't take the time to make a run of less than 6 of a single profile. Hickory Tool will make just one, but as has already been explained, it can be done on a table saw. When I have a few feet of a particular molding to make, I use old molding planes. You can make anything with hollows, rounds, and a few others. You could even make this profile with only a shoulder, or rabbet plane that isn't too wide for the middle flat part. Knock most of the wood out of the way on a table saw, and it would only take ten minutes, or so, to carry it down the rest of the way with a plane. Quote
sunadmin Posted October 30, 2017 Author Report Posted October 30, 2017 Wanted to update the thread. I was able to recreate the moulding using a dado stack and 0 tolerance plate. See attached. Thanks everyone! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.