pkinneb Posted October 8 Author Report Posted October 8 On 10/8/2026 at 10:55 AM, Chet said: Does your measurement of the lines on the staves ensuring that no canvas can drag in the dado? That's correct you do not want the canvas and glue causing issues. Quote
Popular Post pkinneb Posted October 9 Author Popular Post Report Posted October 9 Not much time tonight, as I had to clean up leaves for a couple hours, but I did get a few things done. First I marked centers so that I have a reference. Then I cut the panel in two just to make it easier at the table saw After setting up the dado blade, fence, etc I started working on fitting the panels to the track Took a couple of passes and we are getting close now There we go. Still need to do some fine tuning but definitely happy with the fit/look/etc After fine tuning things a bit I will pre finish the panels in preparation for glue up. Still debating on the dividers but suspect I will remake them full at width. Then I need to finalize the till panel so that its ready to go after my hand cut drawer dovetail party 6 Quote
Popular Post pkinneb Posted October 9 Author Popular Post Report Posted October 9 Some fine tuning on the tambour track you can see here it is contacting the back of the track at the corner so I will remove just a little to see if that helps The bottom right is done, you can see on the top right how little I am removing I am happy with the motion now so I will move on to remaking the side panels at full width. First up was layout then I added another mortise towards the back at the PantoRouter. You can see the new mortise in this pic. On a side note its hard to believe I rarely used hand tools in my first 25 years of woodworking, I count 5 in this picture Then I cut the new panels and added dado's ...before using hand tools and the BS to clear away the waste between them. That'll work I also was playing with some panels to cover the gaps on the right and left... not sure if I will go that route or not. If I do I will need to decide on light wood to match drawer fronts and cabinet or darker wood to match the door. 4 Quote
gee-dub Posted October 10 Report Posted October 10 This thing is looking so good. Love your "L" fence. The tambour is a super cool feature. 1 1 Quote
Mark J Posted October 10 Report Posted October 10 15 hours ago, pkinneb said: Is that vise in the picture like a removable Moxon, or is it permanently attached? 1 Quote
pkinneb Posted October 10 Author Report Posted October 10 On 10/10/2026 at 8:12 AM, Mark J said: Is that vise in the picture like a removable Moxon, or is it permanently attached? Its removable, its just mounted in the tail vise. FWIW Its the BC high vise. 2 Quote
Popular Post pkinneb Posted October 11 Author Popular Post Report Posted October 11 Today started with the tambour door stop. First up drill a hole in the top side of the case, in the track, for a 1/4" dowel Cut the dowel down and glue it in. With that done I notched the right door 1/4" making it so the left door stops at the dowel and the right stops over the dowel. Panel prep for finish ...and finally two coats of shellac Then I spent some time doing final ish layouts of the till Inner upper case Upper case door fronts And right main outer door That my friends is a lot of tool holders to design, steal, etc First thing tomorrow is glue up of the drawer case. 8 Quote
Popular Post pkinneb Posted October 11 Author Popular Post Report Posted October 11 Well the glue up was definitely a bit intense but everything went well. I actually glued it up upside down that way I could start with the tambour section, since there were more parts there. Unfortunately I had to focus on what I was doing so no real pics other than this one, at the end, where I was squaring up the case and drawing closed one of the dividers. Haven't used on of those clamps in a while but it worked great here. ...oh and a picture of the aftermath ...then I cleaned up the joints ...and slid it into place Very happy with the result but man that took a while 6 1 Quote
Popular Post pkinneb Posted October 13 Author Popular Post Report Posted October 13 Todays first task was to rough fit the drawer fronts Then I milled stock for the end grain on the lumber core panel for the plane till Glued those up ...then glued them to the panel Here you can see its end grain Next step will be to flush these with the panel then add long grain strips before applying the final face veneers. Wife's gone tomorrow so will most likely be Wednesday for that and the next post. 6 Quote
Mark J Posted October 13 Report Posted October 13 With everything that's already gone into it, I bet that cabinet is starting to get heavy. 2 Quote
Popular Post pkinneb Posted October 13 Author Popular Post Report Posted October 13 On 10/13/2026 at 7:36 AM, Mark J said: With everything that's already gone into it, I bet that cabinet is starting to get heavy. Its actually not that bad but I may weigh it before it goes up. The tools, other than the #5 plane, are actually not that heavy. It will hang on a French cleat which I have used for my clamp racks for years without issue. The clamps weigh waaay more so I don't anticipate any issues. 4 Quote
Popular Post gee-dub Posted October 13 Popular Post Report Posted October 13 Just for input data; I have 3/4" plywood cleats screwed on 16" centers and have an incredible amount of weight on them. I have used this method for years in different shops and never had anything move a bit. There are more tools behind the doors. I never bothered to weigh this rig since I had good success in the past and got over worrying about it. I'm pretty sure you'll be fine no matter what you hang in there. 4 1 Quote
pkinneb Posted October 13 Author Report Posted October 13 On 10/13/2026 at 12:27 PM, gee-dub said: Just for input data; I have 3/4" plywood cleats screwed on 16" centers and have an incredible amount of weight on them. I have used this method for years in different shops and never had anything move a bit. There are more tools behind the doors. I never bothered to weigh this rig since I had good success in the past and got over worrying about it. I'm pretty sure you'll be fine no matter what you hang in there. Thanks that's pretty much what I figured as well. 1 Quote
Popular Post pkinneb Posted October 15 Author Popular Post Report Posted October 15 More yard work tonight so not much progress but... I did clean up the end grain edging and added the long grain strips Also started working on the final 1/8" veneers Oh and I made another filler piece, the gaps were bugging me so pretty sure I will be going with these 5 Quote
pkinneb Posted October 16 Author Report Posted October 16 On 10/4/2026 at 7:11 AM, Ron Swanson Jr. said: are you heading to the expo this year? FYI just got the map of the Expo floor looks like we will be right across the isle from each other. See you tomorrow. 2 Quote
Popular Post pkinneb Posted October 16 Author Popular Post Report Posted October 16 Progress from last two days. Cleaned up the long grain strips. Then glued up the outer veneers and put it in the vacuum bag Didn't turn out great but will work. I got some slight warping, I think I should have used Gorilla glue instead of Titebond on these due to the long time to get it all glued up. I believe the Titebond caused the veneers to curl up by the time I got it in the bag. Test fit it in the case so I could figure out the support dimensions. Then I laid them out Rough cut them on the BS Then taped together before hitting the jointer and sander so that they would match Next up I made the hinge strip for the wooden hinge I hope to use. There is a bit going on here I need to figure out how I will clamp that for glue up... A pic with a plane on it to insure everything will workout...it did not. After the first attempt it stuck out to far but now with some further milling it should work. Next up I milled up the tilt out saw tills (Rob Cosman design). I will have three as well as an extra one for my marking gauges They will fit in this spot on the right side of the plane till I also milled the strips for the plane till layout as well as rough milled the wood for the upper shelf compartment above the plane till. That's it until Sunday as I will be at the MN woodworkers guild expo (Windsor Chair SIG) tomorrow all day. If you're in MPS/ST Paul stop by (state fair grounds in the Progress Center) and say hi should be a great show. 6 Quote
Popular Post pkinneb Posted October 18 Author Popular Post Report Posted October 18 Back it today but unfortunately a great portion of the effort will be fire wood First up spent time cutting the blanks I picked in half after marking them, clearly... Then I laid out and cut the reliefs for the blade and backs at the TS While that turned out fine it was here where I realized the mistake I had made. I laid out the saws backwards so the nice grain match I started with is no longer on the front side. I kept going as I thought it might not be that big of deal. Next I did the Japanese saw till I cleaned up the dado's with a router plane ...and put an extra notch in so the saw would son the handle burring the blade I also added a slope to aid in smoothness while putting the saw in Then I did a test fit / look With the 1/4" spacer on the right it fit as hoped. I will find some extra thin washers for between each till so only one comes open at a time. When I do this I may have to slim the filler panel a bit. It was here I realized I would almost surely be remaking these again but I moved ahead regardless. To keep glue out of the blade / back area's i used tape and only applied glue to one side. With that done I cleaned them up Then made a template for the handles and cut them out. The goal was to have the blades burried. I cleaned them up with rasps That is close enough. At least I will have a pattern now. With the saw tills done I worked on the marking gauge block. This one will not have to be remade. First I started the holes at the drill press and then finished with a hand drill. Bit was too long for the DP. \ With just the holes the marking gauges spun to easily so I used the PantoRouter and the bit I used on the door pulls to add recesses. That solved the issue. Here they are looking form the planned face side And now in the cabinet Yep I will be remaking three of them! 6 Quote
Von Posted October 18 Report Posted October 18 I applaud you for your discipline to remake those. 1 1 Quote
Popular Post Mark J Posted October 19 Popular Post Report Posted October 19 13 hours ago, pkinneb said: Here they are looking form the planned face side And now in the cabinet Yep I will be remaking three of them! You could still mount the saw holders with the planned side out. The saws might look backwards, but when sliding in and out they would ride on the back of the blade, which has no teeth, i.e. smooth. This might be a functional improvement. 3 Quote
Popular Post pkinneb Posted October 19 Author Popular Post Report Posted October 19 On 10/19/2026 at 7:47 AM, Mark J said: You could still mount the saw holders with the planned side out. The saws might look backwards, but when sliding in and out they would ride on the back of the blade, which has no teeth, i.e. smooth. This might be a functional improvement. Thanks! Unfortunately the handles would be backwards which would be very awkward in use. I did have a thought that I could just add a thin veneer to the fronts and visible sides. Now deciding if that's more work than just remaking them. Ultimately with the amount of time I will have into the piece the cost and time to remake them is very minimal especially now that I have the design figured out 4 Quote
Popular Post pkinneb Posted October 21 Author Popular Post Report Posted October 21 No work last night as it was our Windsor chair SIG mtg. Great group of guys and we glued up a Windsor stool so that was fun. Not a lot tonight either but I did get the upper shelf knocked out. Man I can make a mess in short order Kinda at a standstill until I can get to the lumber store Saturday. I need wood for the saw tills and the solid core door panels as well as veneers for the upper doors. I also don't want to go further on the plane till wooden hinge until the tills are done and mounted so I guess I will go back to tool holders for a couple days. Getting down there for remaining items though 3 Quote
Popular Post pkinneb Posted October 22 Author Popular Post Report Posted October 22 Not much to show tonight but I did get the top half of the brace & bit holder done. Here smoothing out the BS cuts at the edge sander Then using my palm router as a router table I added a 1/16" round over on each holder Ready for glue up ...and the finished piece Tomorrow I'll work on the bottom holder and then mount them in the cabinet to the left of the plane till if I have time, need to mow up the leaves again. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.