Popular Post pkinneb Posted November 5 Author Popular Post Report Posted November 5 More tool holders today Using magnets for these After final shaping...decided to continue the curved theme Glued in the magnets, since these are working through about 3/32" of wood I needed two per holder Another one done Progress so far... Just one more to go in this door, the knife block. I started on it tonight but ran out of steam so I will finish it tomorrow. I also need to do more work on the poplar core for the upper doors as I will need the doors to be completed in the next week or so. 5 Quote
Popular Post pkinneb Posted November 6 Author Popular Post Report Posted November 6 Finished up the last holder for this door tonight. Next up layout and drill holes to fasten them to the door, shellac them and the door, and install them. Then back to the plane till wooden hinge & prepping the poplar for the wood core upper door panels. 4 Quote
Von Posted November 6 Report Posted November 6 How did you make the slots for the knife blades? 8 hours ago, pkinneb said: Finished up the last holder for this door tonight. 2 Quote
Popular Post gee-dub Posted November 6 Popular Post Report Posted November 6 You are going to get so much joy out of this thing. Mine is not near as nice but I am still glad whenever I can just reach out and grab a tool knowing right where it will be. 2 1 Quote
pkinneb Posted November 6 Author Report Posted November 6 On 11/6/2026 at 6:18 AM, Von said: How did you make the slots for the knife blades? The block is actually 3 pieces of wood. I cut the blade slots at the bandsaw prior to gluing the bottom and the back on. the top of the red knife holes and the cocobolo handle knife and awl were drilled at the drill press (forstner bit) and then I chiseled angles for the red knifes. Sorry got into a bit of a zone deciding how to do it and didn't take as many pics as I should have. 1 1 Quote
Ron Swanson Jr. Posted November 6 Report Posted November 6 On 11/4/2026 at 7:47 AM, pkinneb said: Yes Hamilton Marking gauges I just ordered one of their making gauges, and discovered this very cool site in the process: https://www.heartwoodtools.com/ Multiple artisan toolmakers on there. 2 Quote
Von Posted November 6 Report Posted November 6 1 hour ago, pkinneb said: The block is actually 3 pieces of wood. I cut the blade slots at the bandsaw prior to gluing the bottom and the back on. the top of the red knife holes and the cocobolo handle knife and awl were drilled at the drill press (forstner bit) and then I chiseled angles for the red knifes. Sorry got into a bit of a zone deciding how to do it and didn't take as many pics as I should have. Thanks and no worries on the pics. I get your process. You are good at making your glue lines invisible. 1 1 Quote
Popular Post pkinneb Posted November 6 Author Popular Post Report Posted November 6 Had to clean up leaves again today, hopefully the last time for the year, so not much shop time but I did get the last door laid out. Also found homes for these in various places just need holders Tomorrow I hope to knock out the plane till, wood hinge, and some more tool holders. 5 Quote
Popular Post pkinneb Posted November 7 Author Popular Post Report Posted November 7 Well the best laid plans...ended up spending a large part of the day on the wood hinge but at least its done lol. Started by making a cutting backer for 3/8" dowel as my normal one is for 1/4" I clamped this to the normal jig (sorry not a get pic). Then I drew a line down the dowel so I could put it back the same orientation after its cut into segments Followed by determining the number of segments (which should always be an odd number) With that completed I started cutting the segments and this is where my problems began. I was not getting a good fit and it needs to be or you will have major problems later. I thought it was the dowels (maybe a smidge to small) so I remade them again, twice!! What I ultimately determined is that I had cut the backer in the wrong saw cut on the jig which introduced just the slightest of angles and it needs to be dead on 90. I fixed this and the problem was solved but unfortunately it took a couple hours to get to this point The dowels need to be just the right size to get the hinge holes drill properly as shown here. Ok finally ready to prep for glue up I determined which segments would be waxed on each side and knocked that out using a Q tip. Here you can see the W showing where to wax Then I taped it off as you do not want any wax on the glue sections, confirming before waxing that everything lines up and is correct Waxing the sections Then using Q tips again I added glue and used blue tape as a clamp, which worked well. One thing I didn't think about is on a typical box the hinge is captured by the sides keeping everything tight. Here that was not the case and I had a couple of slight gaps so I grabbed a quick grip clamp and used it to draw them tight, it worked fine. and it works ...after a few hours I will plane this side of the hinge flat with the till. Oh and a quick test fit to insure it still fits. While the hinge dried I started working on the plane till tool holders. Pretty straight forward. My #5 is a tight fit so to make some room I used a used the router table to make a recess, and then a small round file to relieve the edges a bit so it would slide down about 3/8" Most are done but I need to start attaching them for final fits I started with the bottom which is also the handle to lift the till and access the storage underneath Another test fit Till open ...and with that my wife was calling me for dinner. Damn I can make a mess in an afternoon Not sure if I will get anything done tomorrow need to wash my truck and wife's car as it may be the last time until spring for a driveway wash, based on the weather outlook. Not complaining as this is pretty late in the year to see 50's here. 6 Quote
Von Posted November 8 Report Posted November 8 What keeps the two parts of the hinge from separating? Friction? Looking great! 1 Quote
Popular Post pkinneb Posted November 8 Author Popular Post Report Posted November 8 On 11/7/2026 at 7:32 PM, Von said: What keeps the two parts of the hinge from separating? Friction? Looking great! Sorry about that. Here are some pics, it's a 1/16" rod you place in the holes you drill about 1/4" each side before its glued in place. like so 3 1 Quote
Von Posted November 8 Report Posted November 8 No apology called for - thanks for sharing! I was trying to figure out how you got one length of rod down the whole thing and your approach is much more elegant. 2 Quote
Popular Post pkinneb Posted November 10 Author Popular Post Report Posted November 10 Not much to show tonight but down to one plane holder to go... 5 Quote
Mark J Posted November 10 Report Posted November 10 Are you able to lift the plane till, to open the secret storage space, with the planes in place? 2 Quote
Chet Posted November 10 Report Posted November 10 On 11/10/2026 at 5:45 AM, Mark J said: Are you able to lift the plane till, to open the secret storage space, with the planes in place? I was wondering the same thing. 1 Quote
Ron Swanson Jr. Posted November 10 Report Posted November 10 Not trying to answer for @pkinneb, but I think the answer is YES. As long as you don't let it slam shut I think the planes should stay put. He may also have embedded some magnets to help (?). Just guessing. 1 Quote
Popular Post pkinneb Posted November 10 Author Popular Post Report Posted November 10 On 11/10/2026 at 7:45 AM, Mark J said: Are you able to lift the plane till, to open the secret storage space, with the planes in place? On 11/10/2026 at 10:48 AM, Chet said: I was wondering the same thing. The top row will need to be removed for two reasons; first, the knobs will contact the bottom of the upper storage area and two, weight as I would be concerned it would stress the wooden hinge. On 11/10/2026 at 11:03 AM, Ron Swanson Jr. said: Not trying to answer for @pkinneb, but I think the answer is YES. As long as you don't let it slam shut I think the planes should stay out. He may also have embedded some magnets to help (?). Just guessing. You are correct there will be magnets on a couple tools like the small router plane and the shoulder plane for sure. 4 Quote
gee-dub Posted November 11 Report Posted November 11 Nicely done. It is funny how sometimes the little things can suck up as much time as the big things. 1 Quote
Popular Post pkinneb Posted November 11 Author Popular Post Report Posted November 11 On 11/10/2026 at 7:03 PM, gee-dub said: Nicely done. It is funny how sometimes the little things can suck up as much time as the big things. For sure!! Another 3 hrs tonight and no new pics... Other than the hinges I really don't want any visible hardware on the outer panels. So as you can imagine screwing things down from the back side requires a lot of measuring and double checking to insure you drill in the appropriate places. I think it will be worth it but never thought it would take so long. 4 Quote
Popular Post pkinneb Posted November 12 Author Popular Post Report Posted November 12 Ok all the plane till tool holders are made and the bottom row is all fastened. I need to fasten the top pieces and imbed some magnets for the shoulder plane and the small router plane. Once complete this and the right side outer door holders will be ready for finish and final assembly. The skew block plane and and the Stanley 79 needed front hold downs so they were more secure. 7 Quote
Popular Post pkinneb Posted Friday at 10:34 PM Author Popular Post Report Posted Friday at 10:34 PM Ok everything is fastened down...finally! I did lower the skew plane holder and rounded over the top of it to allow better access. Here is a little better pic of the hold downs on these two Next up was to add the magnets. For the router plane I just drilled 3/4" holes with a forstner bit. For the shoulder plane I used a 3/8" x 2 1/4" flat magnet. To insure I didn't go to far I made a small block (thanks for the recent tip @gee-dub) and drilled it out Then cleaned it up with chisels and a router plane All glued in...just a few screws huh? lol Last up today I finished the LN brush holder. I used dowels to add support and drilled the arms using this dowel jig, I believe I purchased from someone on this forum years ago That'll work First up tomorrow get some finish on the till, holders, and inner doors. Then more tool holders... 3 Quote
Popular Post pkinneb Posted Saturday at 11:26 PM Author Popular Post Report Posted Saturday at 11:26 PM Finished up the magnetic catches for the inner doors today Then after spending a couple hours on misc odds and ends I applied a couple coats of shellac on the inner doors, plane till, shelves, and tool holders. Then the outer door backs and edges that had not been done previously 5 Quote
Popular Post pkinneb Posted Sunday at 11:39 PM Author Popular Post Report Posted Sunday at 11:39 PM First up a quick sand (220) of the parts I shellaced yesterday Then wipe down, just paper towel with a mist of water The finish is shellac mixed 1 part shellac 2 parts denatured alcohol (for my first coat I do 1/1). for my second and third coats I use these cups from Home Depot, they have ratio marks (on the other side ) and lids which is nice. ...and t-shirt material, I got this batch from Mcfeelys and they were a nice size. I like to make several folds like so, and then apply With that complete it was time to start (re)attaching the tool holders I also came up with a much simpler way to get accurate layout. I used tape and pencil marks on the face side and then drilling a small guide hole also from the face before flipping over, clamping the holder in place and final drilling from the back side. A couple holders were a titch tight so I fixed it with a sharp chisel I also broke one of the square holders as I drilled to close to the edge and snaped it while screwing it in. It was quick to re make it. ...and with that we are ready to add tools Its been a long project but I am definitely liking the progress... Still on the list: finish the holders for the right side back door, make the upper lumber core doors, tool holders for those, and make the drawers... 7 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.