Popular Post pkinneb Posted December 5, 2025 Popular Post Report Posted December 5, 2025 On 12/5/2025 at 12:52 PM, gee-dub said: Sorry this is blurry. This just shows the little blobs of silicone glue I put in the panel grooves to act as custom space balls. The silicone sets up very slowly so once you have glued up the frames you can micro-adjust the panels. The next day they are well set but still allowed to flex over the seasons. But I have a lot . . . . . . and have developed the attitude that if I would like another pressure point on an assembly . . . why not? Great tip on the silicone! I don't think I have ever seen this shot of your shop. I think you may have more clamps than I do...I like it Project looks great! 1 2 Quote
Popular Post Coop Posted December 6, 2025 Popular Post Report Posted December 6, 2025 On 11/26/2025 at 5:26 PM, gee-dub said: I use Prismacolor. They are not inexpensive but I bought a box of 12 in 2016 and still have 6 left so . . . They are great for walnut, Peruvian walnut, red oak, and other dark woods. 2 bucks a pencil ain’t bad. Just ordered myself a stocking stuffer to go along with my Cracker Barrel gift card. 3 Quote
Coop Posted December 6, 2025 Report Posted December 6, 2025 On 12/5/2025 at 9:30 PM, Coop said: 2 bucks a pencil ain’t bad. Just ordered myself a stocking stuffer to go along with my Cracker Barrel gift card. In fact, I won’t live long enough to use all 12 so, the first 8 people to pm me with your name and address, I’ll stick one in the mail for your review, assuming that USPS will allow a pencil in an envelope. 2 Quote
Popular Post gee-dub Posted December 7, 2025 Author Popular Post Report Posted December 7, 2025 Breaking out blanks for the rails and stiles of the divider panel; left side of the drawer case, to the right of your knees when seated. Witness marks as previously discussed. Here again there is a defect in the material but I will cut out my parts around it . . . happy fire pit I use a couple pieces of the material to be resawn to setup the feather boards. With a rip blade in place and using a feather board I get pretty clean cuts right off the saw. I keep some of the dimensioned spoil to help me setup for joinery later. My favorite wheel gauge has gotten a lot of use lately. Time for a sharpening. A squirt of mineral spirits on a 1200 mesh diamond stone. I just rest my finger on the top and move the wheel in a random pattern around the stone. This quickly puts an edge on it suitable for its use. I slice the fibers on the rails and stiles. This yields a nice clean cut at the router table. Here's the joinery for these frame parts. It goes together like so. I need to final-size these panels and rabbet them to fit in the frame. I hope to get to that before end of day because I can lay on the initial color coat. Floating panels get colored prior to assembly to assure there is no bare wood exposed during the seasonal movement. 4 Quote
Popular Post gee-dub Posted December 8, 2025 Author Popular Post Report Posted December 8, 2025 These end panels are glued and cured and ready for surface prep so I will set them aside until I go into my surface prep marathon prior to slapping on some finish These are the floating panel blanks for the knee panel shown in the previous post. They get cut to final size, rabbeted and so forth. Sorry about the color discrepancy. I took a couple of these with my phone and it tried to "fix" stuff. At any rate, the outer panels have some reversing grain so I take a really light cut to establish the rabbet's shoulder. Then a couple more passes to make final depth. This gives me this reveal. I pre-finish the panels like I do all floating panels. Time for some late breakfast 9 Quote
gee-dub Posted December 9, 2025 Author Report Posted December 9, 2025 On 12/5/2025 at 8:03 PM, Coop said: In fact, I won’t live long enough to use all 12 so, the first 8 people to pm me with your name and address, I’ll stick one in the mail for your review, assuming that USPS will allow a pencil in an envelope. Just an observation . . . the white leads are quite soft and get consumed rather quickly I have carpenter's pencils that I have been wearing down for years. Not so with the soft white lead pencils. 2 Quote
Popular Post Chet Posted December 9, 2025 Popular Post Report Posted December 9, 2025 On 12/9/2025 at 12:23 PM, gee-dub said: Just an observation . . . the white leads are quite soft and get consumed rather quickly I have been using the white Prisma pencils ever since I borrowed on from my grand daughter. She uses them for her artwork but never uses white so each time she gets a new set I get the white one. They do wear quickly, probably because the "lead" is basically the pigment and a wax binder making it possible for the artist type people to blend the colors in their drawings. At least that what my grand daughter told me. 3 Quote
Coop Posted December 10, 2025 Report Posted December 10, 2025 I used mine for the first time today on some walnut and they mark much easier than the ones I’ve been using probably due to the fact that they are softer and do wear down easier. Fair trade off! 1 Quote
Popular Post gee-dub Posted December 10, 2025 Author Popular Post Report Posted December 10, 2025 Didn't get a whole lot done today but don't feel too bad about it. I was helping a neighbor get some stuff down at the rear of his property so, paying it forward. He helps me out all the time as well. I had pre-finished the edges of the frame panel recesses since they can be hard to reach. I have done them before with an oil painter's brush but thought this might be easier. I position the floating panels with the little dabs of silicone I use as "space balls". I use some curved cauls to clamp the assembly flat to a work surface till tomorrow. The previously assembled end panels mount at an angle. I failed to pay attention and did not angle cut the top rails prior to assembly . . . Doh! I add a couple of section of sac-fence to the rip fence to support the odd shaped lower portion and allow me to cut the bevel. There we go. How often is our woodworking "recovery" woodworking? ;-) I lay out some marking on the leg pieces and will cut the mortises tomorrow. 5 Quote
Popular Post gee-dub Posted December 10, 2025 Author Popular Post Report Posted December 10, 2025 This morning is about the opposite of yesterday. Sometimes you spend a lot of time and have little to show for it. Other times you do very little but it looks like a lot. I use a 1-2-3 block to transfer my mortise position marks from the panel to a piece of scrap I will use as a story stick. I re-task my template routing sled to hold the story stick to the leg to act as a fence. I use the Domino to cut a series of mortises. One side on one panel. Both sides on both panels. I will set these over in the "surface prep" pile for final profiling, sanding, whatever. 7 Quote
Popular Post gee-dub Posted December 10, 2025 Author Popular Post Report Posted December 10, 2025 I wander over to the old swinging plywood rack. Baltic Birch, as wonderful as it is, can vary by a 64th in thickness so I measure. This shop made doo-hickey makes it easy to set bit depth to match the plywood thickness. I use the aluminum extrusions again to expand the capacity of the router table fence. I run a shallow cut between the stops to set the shoulder. Then two more passes to reach the 1/2" depth I am after. This is a 1/2" rabbet to accept the ply and a surface depth to match the actual plywood thickness. The outer panel is angled so I add a vertical plywood panel to accept the drawer glides. I have tried a few of these corner "knock out" chisel setups. The Veritas magnetic one is the best so far. And we end up with this receiver for the plywood panel. I'll do the other one and knock off for the day. It is pathetic but I just run out of gas so much quicker than I used to . . . 5 Quote
Mark J Posted December 11, 2025 Report Posted December 11, 2025 13 hours ago, gee-dub said: It is pathetic but I just run out of gas so much quicker than I used to . . . Sadly true. 1 Quote
Popular Post gee-dub Posted December 12, 2025 Author Popular Post Report Posted December 12, 2025 I imagine many of you have used the iron and damp towel trick to raise dents. This iron is pretty cheap and keeps me from stealing the one out of the house when I need one. I use it dry and lay a bit of damp paper towel on the dent . . . presto. I glue and clamp one side of the vanity. Let me spend more of your money for you or suggest a 'wish list' item for Christmas. These little card scrapers are inexpensive and super handy for tight spots. Here is another plug for shop organization. I went from sub-assemblies clamped up on multiple surfaces, tools laying everywhere, and clamps in place to a shop reset in under a half an hour. A place for (almost) everything and everything in that place. I'm now all set for the next phase which is the exposed side panel in the leg area. I goofed up and routed a rabbet I didn't need. Of course this was in an exposed area so a repair (or a new leg) was required. The repair is on the left side of the leg and will be on the inside surface of the leg area. I think I will get away with it. Here is a Tim Rousseau trick. He cuts a plastic straw at an angle with a scissors. Runs the point of the cut straw up the mating joint where the glue squeeze-out occurs. Snip off the tip of the straw again and repeat. Works great. He also uses wet rags, acid brushes with the bristles cut short and chisels; all of which I also do either learned from him or someone else. I will let this guy set up. then I need to cut a few plywood components and percolate on the drawer fronts. 8 Quote
Mark J Posted December 13, 2025 Report Posted December 13, 2025 18 hours ago, gee-dub said: The repair is on the left side of the leg and will be on the inside surface of the leg area. I think I will get away with it. I can't even see it when you point it out, so, yeah, I think you'll get away with it. 1 1 Quote
Popular Post Von Posted December 13, 2025 Popular Post Report Posted December 13, 2025 On 12/12/2025 at 2:07 PM, gee-dub said: I imagine many of you have used the iron and damp towel trick to raise dents. This iron is pretty cheap and keeps me from stealing the one out of the house when I need one. I use it dry and lay a bit of damp paper towel on the dent . . . presto. I picked up my shop iron at my local Habitat Restore very cheap and consistently see them there. Good suggestion to have one for the shop. 4 Quote
Popular Post gee-dub Posted December 13, 2025 Author Popular Post Report Posted December 13, 2025 Out of state visitors today so I didn't get a whole lot done this morning. I did however have a great breakfast at one of their (they used to live in SoCal) favorite diners they visit whenever they come this way. Of course we forgot some items at the grocery store so guess who gets to make a last minute run? You can see the multiple tenon and floating back slat joinery here. It is on its back with its feet in your face but you start to get the general idea here. This is just a dry fit so I can confirm the drawer case and face frame dimensions. I hope to pick this up when I am back from the store. there is a lot of day left 6 Quote
Coop Posted December 14, 2025 Report Posted December 14, 2025 I like the way you transitioned the bottom rails into the legs. That’s a neat detail! 1 1 Quote
Popular Post gee-dub Posted December 14, 2025 Author Popular Post Report Posted December 14, 2025 On 12/13/2025 at 5:41 PM, Coop said: I like the way you transitioned the bottom rails into the legs. That’s a neat detail! Thanks. It echos the blanket chest and dressers that it will share the space with. This is a dresser end panel. 4 Quote
Chet Posted December 14, 2025 Report Posted December 14, 2025 On 12/13/2025 at 5:41 PM, Coop said: I like the way you transitioned the bottom rails into the legs. That’s a neat detail! What Coop said! Quote
Popular Post gee-dub Posted December 22, 2025 Author Popular Post Report Posted December 22, 2025 Just so you don't think I've wandered off . . . I've always been glad I made this sled a bit deeper than I originally planned. It comes in handy for things that are just a bit too big for my other sled. This panel gets let in to the side assembly to provide a vertical surface for the drawer slides. I simply glue it into place. The inevitable irregularity of plywood left an area a bit proud. A quick fix with a beater chisel adjusts the area for the joinery. The same operation for the plywood panel for the interior of the other side of the drawer case. I sort of laminate the frame and panel show piece to the ply. I use glue in certain places to still allow for some wood movement although there shouldn't be much. Can't emphasize enough how often a tube sock filled with glass beads from the dollar store comes in handy. This soft weight holds all sorts of odd things as a third hand. I true up the panel/ply combo. It will end up here with some additional frame and trim pieces. Ever onward . . . 3 Quote
Popular Post gee-dub Posted December 22, 2025 Author Popular Post Report Posted December 22, 2025 Posting baby-steps today. It helps me keep moving forward . . . that's right . . . I'm using you. I use this Lee Valley small box slotting bit to cut a stopped 1/8" x 5/16" slot in the panel edge and the associated trim piece. I cut a couple of strips of dual-tempered hardboard to use as splines. I have attached face frame material and trim with pins, pocket screws, and splines. This seemed like a good time for a spline since there is not a lot of rock-solid support structure around this drawer box. At any rate it ends up here. There will be a domino at the top of the trim piece. The bottom horizontal support that will be shown later will be pocket hole screwed into place. All in all with the amount of bearing surface I think it will do well with the under mount slides. 6 Quote
Ron Swanson Jr. Posted December 22, 2025 Report Posted December 22, 2025 On 12/22/2025 at 12:38 PM, gee-dub said: All in all with the amount of bearing surface I think it will do well with the under mount slides. I really like the under mount drawer slides. It's a pet peeve i guess, but i don't like the look of a drawer slide on the side of a drawer box. 2 Quote
Popular Post gee-dub Posted December 22, 2025 Author Popular Post Report Posted December 22, 2025 On 12/22/2025 at 2:30 PM, Ron Swanson Jr. said: I really like the under mount drawer slides. It's a pet peeve i guess, but i don't like the look of a drawer slide on the side of a drawer box. I'm with you. I was a late-adopter. I just couldn't see the cost. Then I realized I had spent hundreds of dollars in material, made my own pulls, and spent many hours on a piece. What was a couple hundred bucks for some quality, hidden hardware? 4 Quote
Popular Post gee-dub Posted December 23, 2025 Author Popular Post Report Posted December 23, 2025 Like other mortise and tenon or floating tenon joints the domino makes a nice tight fitting, twist free joint. Back when 99-cents stores were 99-cents I bought $20 worth of wax paper . . . still using it. A little wax paper now makes for much less clean up later. There is an offset at this joint so I used a spare shop made clamping square as a spacer. I used a dead blow to knock these joints together. Not usually a problem but I got careless and hit with the edge of the head as opposed to the flat. Dent! Even though I go over things prior to applying finish, I go ahead and tag this one to be handled before I get that close to the finish line (pun intended). I have a selection of bar gauges. Still I will find myself, like now, with a dimension that I do not have pre-made bars for. The dimension is just large enough to not let me use a couple of 6" rulers and a spring clamp and just small enough to not let me use a 12" rule. I go to the scrap barrel. I dig out a thin off cut and round the tips at the disc sander. This and a couple of stair gauges let me make a quick ad-hoc bar gauge that will work for me. Now I can confirm parallel and square for the drawer box prior to driving the pocket hole screws. You can come up with the quickest and easiest solutions just using scrap from around the shop. 8 Quote
Coop Posted December 24, 2025 Report Posted December 24, 2025 Stair gauges. Those are pretty cool. I can see where they would come in handy as you suggested and other un-intended purposes. And inexpensive as well make them my after Christmas gift to myself! 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.