Popular Post gee-dub Posted November 16, 2025 Author Popular Post Report Posted November 16, 2025 It is amazing the number of tools we collect over a couple of decades. It always puts a smile on my face when I am confronted with a task, percolate on the situation for a bit and (cue the light bulb over the head) "Wait, I have something for that!". 5 Quote
Popular Post Tom King Posted November 16, 2025 Popular Post Report Posted November 16, 2025 I would be really disappointed if I didn't have a tool for anything I need to work on. Getting close to the point where I don't need to buy any more. 3 Quote
Popular Post fcschoenthal Posted November 16, 2025 Popular Post Report Posted November 16, 2025 On 11/16/2025 at 9:41 AM, Tom King said: I would be really disappointed if I didn't have a tool for anything I need to work on. Getting close to the point where I don't need to buy any more. I should be past that point already if you look at my shop. But they'll always invent a better version or I'll forget that I've got something already. 3 Quote
Popular Post gee-dub Posted November 16, 2025 Author Popular Post Report Posted November 16, 2025 I am trying to use up some shorts on this piece as there will be a lot of "secondary" material positions that will not show; inside or behind the drawer case and so forth. Here I am grooving the upper and lower rear stretchers to receive the back slats. I use my standard resaw setup to cut some thinner stock from some odd cutoffs from a previous project. There are checks and splits but the size of the parts I need should be able to be taken from around the defects. I believe I have enough here. Cut to rough length and being edge jointed before being ripped to width. I rabbet alternate edges to allow a lap joinery on the vertical edges of the slats. Still not cut to final length. I want to be able to work around the defects as much as possible. I have an old multi-beading bit I picked up at a woodworking show back in 2005. I cannot believe how much use I have gotten out of this thing. This profile will echo the profile used on the headboard that will be in the same room. The slats kind of go together like so. Again I am using up scraps on this so will have to do a bit of fiddling with the color matching. I have a wide array of Transtint dyes so this is generally not a problem. 7 Quote
Ron Swanson Jr. Posted November 17, 2025 Report Posted November 17, 2025 I really appreciate the systematic way you go about your projects. I'm sure this will be another stunner! 1 Quote
Popular Post gee-dub Posted November 17, 2025 Author Popular Post Report Posted November 17, 2025 Boy, that was a close one. I was using pieces of like milled scrap for setups. I boogered an end and so moved the stop block. Fortunately I noticed or all my slat prep would have ended up this short. Got that resolved and now on to the router table to rabbet the ends of each slat. You guys have seen my "bundle-o-sticks" before. I use these to let me quickly and reliably setup the spacing between back slats. This gives me an actual measurement so I can prepare for assembly. I will use the same sticks during assembly so everything should be same-same . Now I have to see about some of that color matching. I only really care about the pieces that will show in the knee space of the vanity sitting area. Some slats will be behind the drawer case and never seen. These are things I do on my own furniture that I never did when building for someone else. It is kind of liberating 4 Quote
Popular Post gee-dub Posted November 17, 2025 Author Popular Post Report Posted November 17, 2025 For lots of semi-identical parts I tend to use felt pen dots (although more than about 5 get problematic), alphabet, or roman numerals to keep things in order. Yes, I know the last one should have been IX . . . I'm a goof. Once cut to final length I ended up with a batch of oddly decorative kindling for the fire pit. I try to do the simple things first. Before I broke out the dye I tried some Watco Dark Walnut to color the really sappy slats; the two on the left, not the one on the right. It seemed to do the trick. The piece on the left is Watco'd, the piece on the right is plain with a wipe of mineral spirits to simulate how it will look once the overall finish blend is applied. Some other pieces were a bit more stubborn but a little Transtint dye took care of that. They should even out well once the overall color and top coat is applied. 8 Quote
Popular Post gee-dub Posted November 21, 2025 Author Popular Post Report Posted November 21, 2025 Most of these are color matched well enough to take the colored next coats. The two on the left need no additional colorants at this stage. I cut the top and bottom rear stretchers to final length. When I cross cut the legs to final length I forgot to transfer the position marker so I had to do the "which leg goes where?" dance again. I normally avoid using machine surfaces as work surfaces but I needed something long enough to let me get the clamp heads off the surface. When I have to transfer markings on stair-stepped parts I will mark the thinner parts first. Then I slide a setup block up to that line. I put some other thing like this little double square against the block and transfer the mark. And you get this. I setup these auto-adjust Bessey toggle clamps for use on the Domino Table some time ago. With my advancing arthritis issues they have been a god send. The "come and get it" wireless doorbell I have set up for LOML is ringing so I will take a break for a bit and then get back at it. 6 Quote
Popular Post Von Posted November 22, 2025 Popular Post Report Posted November 22, 2025 I don't always comment since it seems repetitive, but I always appreciate your little tips and tricks like the mark transfer. 3 1 Quote
Popular Post Mark J Posted November 22, 2025 Popular Post Report Posted November 22, 2025 I agree. I think the clever solutions people come up with is one of the best things about the forum. 3 Quote
Popular Post gee-dub Posted November 22, 2025 Author Popular Post Report Posted November 22, 2025 I have to say that most of the things I share here I learned from someone else out there that was willing to share. I agree that one of the main values of the forums is the information on operations and methods that we share with each other . 5 Quote
Popular Post gee-dub Posted November 22, 2025 Author Popular Post Report Posted November 22, 2025 I sometimes want Dominoes that are outside the usually available. They are easily and cheaply made out of scrap. I do use TaylorTools commecrial Dominoes for standard sizes because they are well priced and easy. I join the rear stretchers to the legs with 3 tenons at each joint. Hmm, things are not lining up correctly??? I find that some of my panel spacers are not consistently 1/8". The cumulative error makes itself known. What's that old saying? Measure twice . . . I fix that and move on to the stopped grooves that will accept the rear panel slats at the left and right legs. Please, please, always make sure your machine is unplugged if your hands are going to be near the cutters during setup. This is my usual for long stopped grooves. That gets me here. And the dry fit is now a success. I will splash on some pre-finish to assure that no bare wood appears during seasonal wood movement. Then it is off to the oldest grandchilds football game and some lunch. 6 Quote
Popular Post gee-dub Posted November 23, 2025 Author Popular Post Report Posted November 23, 2025 Life intervened for a bit but in a good way; grandkid events and visits. I got the mortise and tenon joinery for the front legs and front stretcher done. The stretcher is quite thin to allow for one's legs to slide under the top when seated at the vanity. The lateral strength will come from the leg to side panel joinery which you will see soon. This has come up now and then. When making straight cuts I don't really care if the guides are in play or not. A bit of effort during machine setup pays dividends down the road for a long, long, time. Another example of the same thing. I am not trying to show anything in particular. It is just that if I am not cutting curves I really don't care about the guides. We end up with a stack-o-blanks. Since they have been face jointed and then parallel planed you get to edge joint or rip to width "downhill" every time; no restrictions. I always "witness mark" things. I am pretty sure I remember where I am but, I do get interrupted and witness marks let me know I have gotten to where I need to go when milling, hand planing, rasping, etc. A few pencil strokes are cheap insurance. And here we are face jointed and planed as well as edge jointed. I use some double-stacked feather boards for resawing. There are a lot of ways and products that help with this; pick your favorite. I want 1/2" floating panels when I am done so I will resaw to 9/16". Like so. Again with the witness marks at the planer. I use the previously trued up faces as the reference surface for the planing after resaw. Here is a great example of witness marks telling me that 17/32" is not enough. I adjust and forge ahead. I end up with nice book-matched panels. The wide ones will be on the outer end panels. The narrow ones will fill in the inner panel and I will end up with a matched pair to spare. 9 Quote
pkinneb Posted November 26, 2025 Report Posted November 26, 2025 @gee-dub good tip on two feather boards I need to try that! What are you using to mark the wood I have tried a couple white pencils but neither leave marks that good. Quote
Popular Post gee-dub Posted November 26, 2025 Author Popular Post Report Posted November 26, 2025 I use Prismacolor. They are not inexpensive but I bought a box of 12 in 2016 and still have 6 left so . . . They are great for walnut, Peruvian walnut, red oak, and other dark woods. 3 1 Quote
pkinneb Posted November 27, 2025 Report Posted November 27, 2025 Thanks!! Added them to my Amazon wish list 1 Quote
Popular Post gee-dub Posted November 27, 2025 Author Popular Post Report Posted November 27, 2025 Moving on to the frames for the side panels. I use a scrap of melamine hardboard that came from some commercial bathroom cabinet or something for a template. The yellow thing is one of a 4 or 5 piece template set I bought at a woodworking show way back when. The silly things come in handy way more often than I ever expected. I use the spindle sander fence trick to help me make a nice smooth transition on this thing. This will work. I draw the curve with a white pencil. Cut it out close on the bandsaw, use the spindle sander fence and end up here. I am always surprised at how many parts go into our furniture. I haven't even made the drawer case, drawer boxes, false fronts, or pulls yet. 7 Quote
Popular Post Chet Posted November 27, 2025 Popular Post Report Posted November 27, 2025 On 11/27/2025 at 9:05 AM, gee-dub said: I haven't even made the drawer case, drawer boxes, false fronts, or pulls yet. Sometimes it feels like a project is coming along and then you realize that it really has a ways to go. 4 Quote
Popular Post gee-dub Posted November 28, 2025 Author Popular Post Report Posted November 28, 2025 I know there are mixed reviews on these and there should be. Hand tools are very tactile; hand held powered routers are as well IMHO. What works for one may not be right for another but, I digress . . . . I love this Veritas medium shoulder plane. I do fit tenons with a chisel as well but I love me some shoulder plane . Ruler stops come in a lot of flavors. I don't know if Garrett Wade still make theirs but, they are my favorite. I find them really handy for centering things. I measure from one side and mark. I measure from the other side and mark. Even if I am off a bit. I still have a very usable mark to keep me moving forward. I like using chalk because as I move through the process I can remove the marks with a damp paper towel or rag and re-mark. Here is a dry fit with the flush floating panels. I am bushed. I think I am still experiencing food-coma hangover from turkey day. We'll see if I get anything more done today 8 Quote
fcschoenthal Posted November 29, 2025 Report Posted November 29, 2025 On 11/28/2025 at 1:55 PM, gee-dub said: I love this Veritas medium shoulder plane. I tried both styles, and like you, I prefer the feel of the Veritas. 1 Quote
Von Posted November 29, 2025 Report Posted November 29, 2025 On 11/28/2025 at 2:55 PM, gee-dub said: Ruler stops come in a lot of flavors. I don't know if Garrett Wade still make theirs but, they are my favorite. I like your tips better when they don't add to my shopping list :-) In all seriousness, thanks. It doesn't look like Garrett Wade sells them any more (I think a see a Veritas version in your photos, which is still for sale). I do find a couple older brass Garrett Wade stops on ebay that are interesting looking but definitely not what you have. I have a couple nondescript stops (TayTools? Rockler?) but I don't tend to think to use them and reach for my combination square in this situation. I can see how the stops would get in the way less. Quote
gee-dub Posted November 29, 2025 Author Report Posted November 29, 2025 @Von - Agreed. A combo square is always at hand. The low profile stops are handy for tight spots. 1 Quote
pkinneb Posted November 29, 2025 Report Posted November 29, 2025 On 11/29/2025 at 7:52 AM, Von said: I like your tips better when they don't add to my shopping list :-) Ok this made me chuckle In that same vein @gee-dub where did you get your pencil holder? That would be nice as they get shorter. As always project looks amazing!! 1 Quote
Popular Post gee-dub Posted November 30, 2025 Author Popular Post Report Posted November 30, 2025 On 11/29/2025 at 3:17 PM, pkinneb said: Ok this made me chuckle In that same vein @gee-dub where did you get your pencil holder? That would be nice as they get shorter. As always project looks amazing!! Pencil holders. Pretty cheap and very handy. They let me use my colored pencils down to the nub. I have some for chalk as well. 2 1 Quote
Popular Post gee-dub Posted December 5, 2025 Author Popular Post Report Posted December 5, 2025 Not a lot of visible progress at this phase. Gluing up the side panels. Check for square, always check for square. Sorry this is blurry. This just shows the little blobs of silicone glue I put in the panel grooves to act as custom space balls. The silicone sets up very slowly so once you have glued up the frames you can micro-adjust the panels. The next day they are well set but still allowed to flex over the seasons. This seems like a lot of clamps. But I have a lot . . . . . . and have developed the attitude that if I would like another pressure point on an assembly . . . why not? 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.