Popular Post Beechwood Chip Posted June 5 Popular Post Report Posted June 5 Hypothetically, if I were going to buy a new or used miter saw, what would you recommend, and what features should I look for. Accuracy, safety and dust collection are my priorities. I'm less concerned about capacity and power. I currently have a DW715 12" non-slider. I figured the sliders had more capacity but also more slop. I don't really have a budget in mind, but the less expensive, the less hypothetical. 2 3 Quote
roughsawn Posted June 5 Report Posted June 5 I bought the 10" sliding Makita this past winter. Very happy with it. Solid, no slop. Cuts a nice 45 every time. Dust control is ok...nothing special. 2 Quote
Von Posted June 5 Report Posted June 5 Make sure you can get/make a zero clearance insert. Good holddowns are a worthy plus. 2 Quote
fcschoenthal Posted June 5 Report Posted June 5 I've got an old 10" Delta and have been thinking seriously about getting a slider. More than the capacity, I want the ability to stop the cut to make a dado so I won't have to switch out my table saw blade and cartridge. I also want one with the shadow line. I've looked at the Dewalt 785, but am considering the Harbor Freight Hercules clone. The reviews put it as just as good, but almost half the price. 2 Quote
Beechwood Chip Posted June 5 Author Report Posted June 5 @fcschoenthal Thanks for mentioning the stopped cuts. That is a nice feature that I had forgotten about. I'm a big fan of the shadow line. I got the Hercules dust extractor and I'm cautiously optimistic about the brand. At that price, this might have become less hypothetical. 1 Quote
Mark J Posted June 5 Report Posted June 5 The Festool K-pex is supposed to be good. I'm very happy with my 20 y/o Makita. Would like one that didn't require so much room behind the saw. Quote
pkinneb Posted June 5 Report Posted June 5 I have had the Bosch Glide for many years and I have been happy with it. Provides a 12" slider without the need for as much room behind the unit. Full disclosure this is a breakdown only tool for me I don't use it as a finish cut saw. I say this becuase while it appears to give great cuts and I have had no issues with the angled cuts for my current deck project I always do final cuts at the TS for fine woodworking projects, which is different than a lot of folks. Quote
Von Posted June 5 Report Posted June 5 On 6/5/2026 at 5:09 AM, Beechwood Chip said: @fcschoenthal Thanks for mentioning the stopped cuts. That is a nice feature that I had forgotten about. I'm a big fan of the shadow line. I got the Hercules dust extractor and I'm cautiously optimistic about the brand. At that price, this might have become less hypothetical. I admit I've never heard the term "shadow line" in this context and had to search for the term - I think we're talking about a laser casting a line down onto the workpiece to show where the blade will cut. Assuming I have that right: +1 - I use the one on my saw all the time. I did spend an afternoon dialing it in. BTW, I would really like to be proven wrong, but I've come to believe dust collection for miter saws is a myth. My system collects so little dust I could go years without emptying it. Granted, I have a small Rigid shop vac and not a Festool dust extractor, but I've yet to hear someone I trust say they have this solved to their satisfaction. 1 Quote
Von Posted June 5 Report Posted June 5 On 6/5/2026 at 7:15 AM, Mark J said: The Festool K-pex is supposed to be good. I'm very happy with my 20 y/o Makita. Would like one that didn't require so much room behind the saw. I have an older Kapex I got used for a good deal and agree it's good, but not a game changer. I wouldn't have paid new tool money for it. +1 to a saw that doesn't require much space behind it. If you get a slider this is a big deal with regards to shop layout. Quote
legenddc Posted June 5 Report Posted June 5 On 6/5/2026 at 8:05 AM, Von said: I admit I've never heard the term "shadow line" in this context and had to search for the term - I think we're talking about a laser casting a line down onto the workpiece to show where the blade will cut. Assuming I have that right: +1 - I use the one on my saw all the time. I did spend an afternoon dialing it in. Some saws have two lights aimed towards the blade and create a shadow. I don't think there's any dialing in needed. I had a 10" Craftsman slider and couldn't get it to cut straight. It was more than good enough for rough breakdown, but putting up molding with it was a recipe for frustration. My shop is too small to keep a miter saw set up all the time and the space needed for the slider just amplified that. Picked up a Dewalt 12" non-slider (716) and really enjoy it. Maybe should have held out for the version with the shadow line but the regular one was what was on sale. 1 Quote
Popular Post Beechwood Chip Posted June 5 Author Popular Post Report Posted June 5 On 6/5/2026 at 9:06 AM, legenddc said: Picked up a Dewalt 12" non-slider (716) and really enjoy it. Maybe should have held out for the version with the shadow line but the regular one was what was on sale. My 715 is the same but it only bevels to one side. It didn't come with the shadow or laser. I tried to install an after market laser but couldn't get it dialed in. Then I got an after market shadow line. It's just a single LED light mounted directly above the blade. It functions as a work light, but as you bring the blade down the shadow is nice and crisp and shows both sides of the kerf. I didn't have to dial it in - it just worked. 3 Quote
DerekMPBS Posted June 5 Report Posted June 5 I bought the Dewalt 780 last year to replace my old one, which I gave to my neighbor in exchange for helping me build a deck. It is very accurate, holds its settings well, and the shadow line is great. There is no adjusting the light, since the shadow cast on the workpiece is from the blade, it is always exact. The biggest issue I have is forgetting to turn the light off when I am done using the saw. 1 Quote
Popular Post Beechwood Chip Posted June 5 Author Popular Post Report Posted June 5 On 6/5/2026 at 4:32 PM, DerekMPBS said: The biggest issue I have is forgetting to turn the light off when I am done using the saw. I have all of my tools set up to turn the dust collector or shop vac on when the tool turns on. This doesn't work well with the miter saw, since I pull the trigger, make the cut, and release the trigger before the shop vac really gets started. So, I set up a work station with a power switch on the front. The switch turns on the vacuum and feeds power to the saw, which turns the light on since I leave that switch always on. When I'm done I remember to turn the switch off because the vacuum is making noise. 5 Quote
legenddc Posted June 5 Report Posted June 5 On 6/5/2026 at 9:28 AM, Beechwood Chip said: My 715 is the same but it only bevels to one side. It didn't come with the shadow or laser. I tried to install an after market laser but couldn't get it dialed in. Then I got an after market shadow line. It's just a single LED light mounted directly above the blade. It functions as a work light, but as you bring the blade down the shadow is nice and crisp and shows both sides of the kerf. I didn't have to dial it in - it just worked. Any chance you have a link to the LED light you bought? Quote
Beechwood Chip Posted June 5 Author Report Posted June 5 On 6/5/2026 at 5:35 PM, legenddc said: Any chance you have a link to the LED light you bought? Good news! I found a link Bad news! No longer available from Amazon https://www.amazon.com/dp/B000X9EDD8 Looks like DeWalt now sells an upgrade kit that "transforms your DWS779 into a DWS780 with an LED shadow light" Quote
Popular Post Tom King Posted June 5 Popular Post Report Posted June 5 I'm currently using my sliding miter saw in working on the barn apartment. I have it set up where I can open the door that used to come in the tackroom behind it. It shoots the sawdust out the door and with a SW wind, which we have most of the time, more than 90 percent of the sawdust is gone out the door with the wind. 3 Quote
Popular Post TheWoodShouter Posted June 21 Popular Post Report Posted June 21 I see this thread is a couple weeks old now, but if anyone is still looking for a new miter saw, Lowes (at least in my market) is currently offering the Bosch GCMSD12 12" dual-bevel sliding compound miter saw for what I think is a crazy good price, it's $449.00 right now. The full retail price is $739, and currently my local Home Depot has this same saw on sale for $639. At $450, I couldn't say no, and I just purchased one today. https://www.lowes.com/pd/Bosch-Glide-12-in-15-Amp-Dual-Bevel-Sliding-Compound-Miter-Saw/3502512 I hope that helps! 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.