Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Signs of an Underpowered Table Saw

Featured Replies

I only have a portable 15 amp jobsite table saw and I know that it is an underpowered saw but what are the signs of the saw being underpowered?

 

I think I have experience time when the saw is bogged down but I am not sure because it could have been a symptom of misalignment. When I was ripping some 8/4 hard maple it would get very hard to feed the piece through and then there would be a good amount of burning on the cut. I checked for any misalignment of the saw but it was all squared up. So could I have just been experience a lack of power from the saw? 

 

Thanks guys

Without a really sharp blade, 8/4 hard maple can give a 3HP cabinet saw a run for its money.  Contractor saws don't like 8/4 hard maple.  I'd say yes, definitely, that saw is underpowered for that particular task.  Get a decent thin kerf rip blade...that's about the best you can do until you upgrade to more HP.

Does it feel like the stock wants to come back at you, or is it more of just needing more effort to push it through?  A thin kerf like eric ^^ mentions makes a big difference on smaller saws..  Also, with maple sharpness is key :). 

 

One last thing is when you're ripping the lumber, are the halves staying pretty straight or are they splaying out / pinching the blade?

Try cutting a little more than half way through the 8/4 than flip the piece end for end run it through again this cut should be about 1/16" strong now raise the blade to  about 1/4" above the 8/4 piece, now set the fence to the accual measurment now run this piece through takeing a 1/16" cleaning cut. This cut is only sliceing 1/16 " off one side of the 8/4 piece which doesn't cause any heat build up

Hi RJ,

 

Your saw is probably under powered. Just try and optimise what you have. Take a look at your user manual. You might be using the equipment outside of it's safety parameters. If you are, know when your beat, retreat with all fingers and visit someone with the right tool. Lots of good guidance on this document. If I have lumber deeper than 8" to deep I dont take risks on our heavy duty saw bench, I take it to another joiner with a band re-saw. If the manual says you can safely cut this depth of timber consider the following

 

  • Sharp rip blade with an appropriate kerf size for your machine.
  • Clean blade with no resin build up.
  • Keep an eye on the kerf. If you have a thin kerf blade the kerf might be a tight fit on the riving knife  (although I see many images of table saws without them fitted, a big no no for me, I always have a riving knife and a crown guard). The kerf may also be closing up after being cut. If this is the case a buddy can help here. Make sure they are well briefed on the safety side of things. Start cutting and then withdraw the timber, keep repeating this until you can get your timber a safe distance past the back of the blade and riving knife. Gently tap a wooden wedge into the kerf to relive the pressure on the blade. 
  • Only apply gentle pressure, don't risk damaging your equipment.

Hope this helps, however please don't take risks with equipment that is not appropriate for the task.

Matthias Wandel turned me on to using smaller blades (i.e. 7 1/4" circular saw blades) in my table saw and I've been ripping happily with them for quite some time.  Up front, you lose some depth of cut:  On my saw, a small blade has a maximum cut of only 2".  But if that's not a deal breaker (such as cutting 8/4 stock) the benefits are legion:

  • They're dirt cheap.  Buy them by the dozen and chuck 'em at the slightest sign of dullness.
  • The shorter radius effectively increases the motor's power at the tooth.
  • They're available in exceedingly thin kerfs, further reducing the saw's workload because you're not removing as much wood.

Find the coarsest blade you can (e.g. 16 teeth or fewer) and give it a try.

Are you using a combo blade or a rip cut blade? I will go against the masses and say that I don't like the thin kerf blades. They are good for ripping as long as there is a sizable waste piece but I find they deflect too much when trying to just shave the edge off a board. I use a portable saw and just take the cut slow and steady.

RJ, I wanted to put my two cents in too. :rolleyes:  If you are using a thin kerf blade and are cutting something like hard maple, you need to be careful not to get the blade too hot. I've seen those blades warp while cutting, and ruin a good piece of lumber.  If you are having to fight the board through the saw, it also puts you at risk as well. All that added pushing toward a spinning blade can result in a really bad day.

The fact that its burning usually indicates some binding or misalignment. I'd double check fence, blade, miter slot alignment. Try cross cutting a piece with ur miter gauge. Do u still get binding and burning? My guess is that u won't. If you do, then u know its a lack of power issue. How are u checking alignment? More accurate method may be in order

Oh, one other thing RJ....the single best item I ever bought for my TS, and maybe my shop, was the GRR Ripper. It improved the quality of my cuts and keeps things much safer. You have so much more control of the work piece because u can keep downward pressure, lateral pressure into the fence, and forward pressure on the work piece. Plus it holds the keeper and waste piece at the same time. It makes cuts possible for me that I wouldn't dare try without it. Microjig's customer service is top notch as well. If u already have a grr ripper, disregard the above post. Hope u figure out ur issue soon. Keep us updated

  • Author

I am using a standard kerf 60 tooth blade. I know it's not ideal for ripping but most of what I work with it 4/4 and it does fine with that. The pieces I was ripping were only 24" inches long. I wouldn't have made the cut if it had been much longer.

 

Boatworks - It just feels like it needs to be pushed harder. When I cut thicker pieces I'll use my Grr-Ripper to get a nice safe grip on the piece to guide it through. Also, the halves are staying straight through the cut. 

 

Higtron -  I thought of this after I made the initial post. 

 

G S - Thanks for the info. I'm sure that the manufacturer doesn't recommend making that cut. 

 

Rob - Thats a pretty good idea. I will have to try that. 

 

Imdanuts - I'm not a fan of the thin kerf blades either. I don't have any experience with them but the deflection aspect worries me about them.

 

Nick - I check my alignment with a dial indicator that is in a jig in the miter slot. When I check everything it was within .003" which is about as good as my saw can get. And I do have a Grrr-Ripper but I would like to get a second one for making the longer rips.

 

Thanks everyone!!

Full kerf + 60T + 8/4 hard maple = way too much for a contractor saw...I wouldn't try to rip that lumber with a 60T blade on my cab saw.  At the very least you need a rip blade if you're gonna rip.  I'd still recommend a thin kerf...no, it's not ideal, but neither is a contractor saw.  It's the easiest way to resolve the problem, or at least make it better.  Look into blade stiffeners if deflection is a concern for you. 

Sixty teeth is far too many for ripping in my book.

 

Most of my ripping is done with either a 24 tooth (10") or a 16 tooth (7 1/4") blade.  Whatever the power your saw has at the arbor, the amount of power it has where the teeth contact the wood is a function of two things:  The radius of the blade and the number of teeth in contact with the wood at any given moment.

 

Find a blade with fewer teeth...the fewer, the better, frankly.  It'll be a coarse cut but in coarseness lies power...and besides, even a fine 80 tooth crosscutting blade isn't going to rip a cut fine enough to get you out of smoothing the edge, anyway.

I agree with the last two posts. I have a powermatic cabinet saw and if I used a blade with 60 teeth for ripping 8/4 maple there woul be similar results. I have a portable jobsite saw with little power also, and have good success with it. If you use the right blade for the right job,(thin kerf rip blade for 8/4 maple) you will have success.

Reducing the saw blade diameter decreases cutting performance by decreasing rim speed and increasing chip load unless you have the ability to increase arbor RPM.

The object is to maintain rim speed. Proper rim speed yields the best results. A lower chip load and sharper blade are the only ways to maintain rim speed short of purchasing a more powerful saw.

Low tooth counts decrease chipload as does a thinner kerf but only if you maiantain rim speed. With less powerful saws rim speed falls quickly due to the low HP motor. You combat that by low tooth counts and thin kerf. You may find that what is touted as a low tooth count rip blade for a guy with a 5hp saw is actually still to high for your lower powered saw.

Don

Motor power is only one aspect of the equation.  Setup and blade selection are also huge factors.  8/4 maple is a tall order for a small saw, but at least optimize the situation by aligning your saw, choosing a sharp good quality 24T thin kerf blade, and making sure the lumber is flat and straight before ripping....uneven, warped, or twisted boards are much harder to cut.  Not all carbide blades are created equal......I'd stick with Infinity, Forrest, Freud, Ridge Carbide, Tenryu, CMT, Amana Tools on the higher end, or Irwin Marples, Freud Diablo, CMT ITK Plus, Guhdo, Amana A.G.E., or DeWalt Precision Trim on the value end, and would completely skip blades from Avanti/Avanti Pro, Irwin Marathon, DeWalt Construction, Oldham Contractor, HF, Ryobi, Workforce, Skil, Vermont American, or any other cheap off-name.  

This is one of those things that's so brilliant, it seems obvious in retrospect. I LOVE this idea.

 

Matthias Wandel turned me on to using smaller blades (i.e. 7 1/4" circular saw blades) in my table saw and I've been ripping happily with them for quite some time.  Up front, you lose some depth of cut:  On my saw, a small blade has a maximum cut of only 2".  But if that's not a deal breaker (such as cutting 8/4 stock) the benefits are legion:

  • They're dirt cheap.  Buy them by the dozen and chuck 'em at the slightest sign of dullness.
  • The shorter radius effectively increases the motor's power at the tooth.
  • They're available in exceedingly thin kerfs, further reducing the saw's workload because you're not removing as much wood.

Find the coarsest blade you can (e.g. 16 teeth or fewer) and give it a try.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.