mds2 Posted July 16, 2013 Report Posted July 16, 2013 Here is a hand tool method question. I am building a cabinet and have to make a stopped rabbet. I am trying to do as much of this by hand as possible. I tried using an old Stanley no. 78, but the distance between the stops is just too short for the plane to be very effective. I thought about trying to chop it out, like a mortise, but was afraid of damaging the peice. I have a small router plane, needs sharpening, but might work ok. I gave up and used my router table, but what is the best hand method to do this? Quote
h3nry Posted July 16, 2013 Report Posted July 16, 2013 I would probably pare away the bulk with a chisel, then clean it up with the router plane if necessary - Although I've only done this on small pieces. I tried using an old Stanley no. 78, but the distance between the stops is just too short for the plane to be very effective. I'm not quite sure how you tried this - To use the 78, I think you would have to chisel out the rabbet next to both stops for a long enough distance for the sole of the plane beyond the blade - then the plane can get to work in between. If you tried this but it was too short for the plane then you might as well finish chiseling out the rest of the rabbet. Being lazy, my preferred solution would be to go back to the drawing board and see if I couldn't redesign the piece without any stopped rabbets, grooves or dados. I too would be interested to hear of any more efficient solutions people have. Quote
nateswoodworks Posted July 16, 2013 Report Posted July 16, 2013 I mark the length with a marking gauge and knife the ends. Then with a chisel deepen the cut a little and remove the waste area with the router plane, rinse and repeat until you get to the depth you desire. Depending on the stock Im using I will stay a little bit away from the ends and then chop to the line at the end. This has worked great for me many times but there are several different ways of doing every precess:) Quote
G S Haydon Posted July 16, 2013 Report Posted July 16, 2013 mds2 I would say you are on the right track. If you have a plough plane I would use this to create a groove to form the upstand of the rebate. If you make a neat little mortice the plough plane can finish at that point. The rest of the waste can then be got rid of working from a gauge line and chisel with a final clean up using a bullnose rebate plane. Quote
mds2 Posted July 16, 2013 Author Report Posted July 16, 2013 Fellow forum member Mel linked me to another forum where this was discussed. Several people recommended not doing a stopped rabbet, but instead going all the way through and then gluing blocks in place. Doing it that way would have easily saved me time, but I'm still curious if there are other methods. I think the Pixies said it best. "Gouge away." Quote
Llama Posted July 17, 2013 Report Posted July 17, 2013 I just thought of this... If the rabbet is shallow and rather narrow, the Lie-Nielsen butt-mortise plane would do a wonderful job. If you are not familiar with this gem of a tool, there is a very good video on YouTube on the LN channel. Quote
RenaissanceWW Posted July 18, 2013 Report Posted July 18, 2013 This really depends on the length of the joint but I have not found a faster way of doing a housed dado like this other than hogging out with a chisel and refining with a router plane. Sometimes you can chisel out a recess at the ends and get a saw in to connect the dots to make the shoulders even cleaner, but you still need to chisel out the waste but now it goes even faster with the long grain fibers cuts. Quote
lemonjello Posted July 28, 2013 Report Posted July 28, 2013 Peter Sellers has a good video on what Shannon just described, I prob saw it on youtube if you look around. Was part of a 4 shelf bookcase. Quote
lemonjello Posted July 29, 2013 Report Posted July 29, 2013 Hardy har har! Peter... Paul... close enough:) Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.