rodger. Posted February 25, 2014 Report Posted February 25, 2014 I made a new bench hook for cutting mitres, and was curious what back saw most people use for cutting mitres: crosscut or rip? Quote
Llama Posted February 25, 2014 Report Posted February 25, 2014 If it's 45 degrees or more it's a crosscut. Quote
Tony Wilkins Posted February 25, 2014 Report Posted February 25, 2014 And here I thought that if it was 44* or less it was a saw cut Quote
G S Haydon Posted February 25, 2014 Report Posted February 25, 2014 Whatever's sharp and close to hand. My gut tells me a cross cut would be best, perhaps a bit cleaner cut with less chance of break out? 1 Quote
Eric. Posted February 25, 2014 Report Posted February 25, 2014 I'm pretty sure if it's 45* or more, it's a crosscut. 1 Quote
Freddie Posted February 25, 2014 Report Posted February 25, 2014 And they're all cuts, so just get a cut saw and eliminate the hassle 1 Quote
Tom King Posted February 25, 2014 Report Posted February 25, 2014 As Graham said, the main thing is sharp. I've always sharpened my miter box saw at the standard crosscut angles of 15 rake and 25 fleam. Some slope helps to clear the sawdust easier too, but it's not that important. A rip saw will give some tearout on the off end of most woods cut at an angle, so any time saved in stroke count would not be worth it. I've never done any experimenting with different tooth geometry for a miter box, since the time doing that would be way more than any difference in cutting with any sharp saw that will cut cleanly. Quote
Tony Wilkins Posted February 25, 2014 Report Posted February 25, 2014 In the Woodwright's Shop where CS comes to build the Dutch Tool Chest they have a discussion on this: http://video.pbs.org/video/2365021526/ I use hybrid filed backsaws so I haven't had to think about it. Quote
Tony Wilkins Posted February 25, 2014 Report Posted February 25, 2014 And here I thought that if it was 44* or less it was a saw cut I fixed it Me too 1 Quote
Llama Posted February 25, 2014 Report Posted February 25, 2014 In my defense I rarely know what I'm talking about! 2 Quote
Trip Posted February 25, 2014 Report Posted February 25, 2014 ==>Whatever's sharp and close to hand Absolutely. Yea, I've got probably six saws more then I need, so I'm as guilty as the next guy -- I really should eBay a few... But as my experience grows, I increasingly use what's at hand -- and what's sharp. Forget who came-up with the three classes of saw cut (think someone on Graham's side of the pond) -- but a #1 or #2 cut, I grab the 'proper' saw... However, 80% of my cuts are #3 where I just go for the sharpest tool siting on the bench... Back to the OP -- for a standard 45degree in 3/4" stock, I'd use a 11/12 tpi CC. But I do file-down the set a bit, so my CCs are not too aggressive... Quote
G S Haydon Posted February 25, 2014 Report Posted February 25, 2014 Had to be us, a class system for sawing! Quote
Trip Posted February 25, 2014 Report Posted February 25, 2014 ==>^^^ Robert Waering His "The Essential Woodworker" is a really good hand-tool book... 2 Quote
rodger. Posted February 25, 2014 Author Report Posted February 25, 2014 Well, looks like a test is in order! I'll do some test cuts and take some snaps of the results! Quote
Llama Posted February 26, 2014 Report Posted February 26, 2014 ==>^^^ Robert Waering His "The Essential Woodworker" is a really good hand-tool book... I bought this book, and I really need to read it. From what I have read, it is very good! 1 Quote
Tom King Posted February 26, 2014 Report Posted February 26, 2014 I was thinking about this, and I think if it cuts across the grain, whether at an angle or not, it's a crosscut. Any "test" would need to be in different woods, at different angles, so I'll just stick with sharp. 1 Quote
Pwalter5110 Posted February 26, 2014 Report Posted February 26, 2014 In my defense I rarely know what I'm talking about! In my defense, I NEVER know what I'm talking about! Quote
Tony Wilkins Posted February 26, 2014 Report Posted February 26, 2014 ==>^^^ Robert Waering His "The Essential Woodworker" is a really good hand-tool book... +1, very good book. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.