Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

wood for mallet

Featured Replies

I have some scrap wood around and need a mallet, so voila.  only question I have is which wood. I have some hard maple that's 3/4" thick so I'd have to laminate it together to make it thick enough, and even then it'll only be about 1.5" thick, not sure that's enough. I "might" have enough to laminate 3 pieces to make it 2.25" which I know is thick enough, but is that strong enough?  I also have some 4/4 walnut that would be thicker but I"m not so sure it'd be hard enough. I know the maple is hard enough just don't know if it'll be thick enough.  as for the walnut, the opposite.  silly Q i know but you guys know more than I do so, there it is.  muchas gracias in advance of course :)

Long grain to long grain glue joints are as strong as the wood itself, so I'd go with three layers of the hard maple.

 

If you don't have enough maple, maybe cut the maple in two large pieces for the two sides, and two smaller pieces for the centers of the two faces.  Then use the walnut for the handle and center of the head.

 

Or, just use maple for one face, and walnut for the rest.

  • Author

thanks, I think I have enough for three layers, I should also be able to cut the center pieces so I don't have to chop out a mortise, which I thought of after I posted.

I have some purpleheart 12/4, hard maple 12/4, and cherry 16/4 scrap chunks that I would like to make into a mallet or few. What glue would you use to put them together? And is it ok if I leave them square faced?

Chef

Regular Tite-bond works well. I can pound concrete with mine. Wouldn't, just could without de lamination. With regard to the face, just know your swing could get awkward but a saw will change the angle at will.

I have some purpleheart 12/4, hard maple 12/4, and cherry 16/4 scrap chunks that I would like to make into a mallet or few. What glue would you use to put them together? And is it ok if I leave them square faced?

Chef

   I cut my faces to 4 or 5 * .  It gives a good face to chisel connection.

  • Author

one more Q... I've read that BLO is a nice finish for mallets but I thought I'd put some arm r seal on it, any thoughts?  I could do either.  maple head and walnut handle, so nice contrasting woods.

Any film finish will flake off the strike head and can irritate the sweaty hand. If you string wrap the handle and go easy on the strike face you could get away with it.

Just realized I assumed a square faced rectangular mallet. "Strike face" takes on an interesting shape with a turned mallet.

I while back I made two mallets - Each out of mahogany and purpleheart. I used the 4-5 degree face angle rule of thumb. I just put two coats of dumb old wipe on poly on them. They have held up just fine over the years of beating on things.

post-2771-0-51561700-1413338855_thumb.jp

 walnut that would be thicker but I"m not so sure it'd be hard enough. 

 

My first mallets were SYP and lasted a long time. I just recently replaced them with ipe mallets. I still use the big SYP mallet if it's handy.

  • Author

Just realized I assumed a square faced rectangular mallet. "Strike face" takes on an interesting shape with a turned mallet.

oh I'm pretty far away from turning anything (especially with no lathe), this will be a flat faced mallet, faces cut at 5 degrees very similar to Chet's (no pegs in mine but those look pretty cool).  waiting for glue to dry, I'll post pics in a couple days when done, pretty happy with the handle.  

Mine is beech with an ash handle. Just wiped over with some arbitrary finish I had in a can but none on the striking faces.

Hard maple will be fine.

I made mine with walnut for the head and maple for the handle. Just the way the dimensions of the scrap worked. Used titebond iii.

The head split once when I whacked a mole a bit too hard...not on a glue line. I just glued it back together and it's been fine. The walnut is a bit softer than I would have liked, but it works for all practical purposes, including swift hard smacks on my 1.5" Barr framing chisel.

  • Author

Wdo, works well on these!

forgive the noobosity here but what is WDO... I can't get 'wood destroying organism' out of my head.  pretty sure you didn't mean that though ;)

forgive the noobosity here but what is WDO... I can't get 'wood destroying organism' out of my head.  pretty sure you didn't mean that though ;)

Watkins Danish Oil!     But,   wood destroying organism  sound like my Table saw!

Those thumbnail images must have come from the prop room of the next Thor movie… After all, who but Asgard’s Thunder God would need so many awesome mallets… I suspect WDO is actually short for some phrase in Old Norse… :)

Those thumbnail images must have come from the prop room of the next Thor movie… After all, who but Asgard’s Thunder God would need so many awesome mallets… I suspect WDO is actually short for some phrase in Old Norse… :)

They are on ebay!  Someone that doesn't know how to build one, will buy, or a lazy woodworker will.  Been on one month and sold 12.   That's why!

They are on ebay!  Someone that doesn't know how to build one, will buy, or a lazy woodworker will.  Been on one month and sold 12.   That's why!

And actually, I'm responsible for 11 of those 12. Bought them to resale on e-bay. Kind of like flipping mallets w/ no improvements necessary :D  

All kidding aside (for the most part), I do have one of Richards mallets and it's a fine hand tool!

Head bowed, hands behind the back and shuffling my feet and red faced!    Thank's Ken!   The check is in the mail!

   Looking good.... Got an ex wife?  No!  I'll loan you one of mine!  Did you try WDO?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.