Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Walnut tree fell. What should I mill it into?

Featured Replies

I had a fairly big walnut tree fall in a recent storm. I want to mill it but I'm not sure into what. I have no woodworking projects planned at the moment but ultimately I would like to do some simple furniture pieces and perhaps some smaller items like boxes and perhaps some trim for my house. Can anyone recommend what dimensions I should cut tree to? What sizes would be the most universal?

 

Also if anyone could briefly list the advantages and disadvantages of walnut wood I would greatly appreciate it. Thank you very much in advance

Not sure how big the tree is but, if I were going to have a walnut tree milled, I'd want 8/4 and the biggest chunks I could get.  From there, I can size out anything I want.  I might also consider some rounds for bowls and such as well.

 

The down side is it will take longer if you're air drying.

 

Walnut is a little on the soft side so, you need to take that into consideration with projects such as tables.  If they're going to see a lot of "kid" abuse, it may look a bit rough after a few years.  Biggest advantages are that it's fairly easy to work and looks absolutely stunning when finish is applied.

Yep, it would help to know how large the tree is. Whether you have it milled 4/4 or 8/4 you are a year or two away from using it on most projects unless you have access to a dry kiln. In that case you'd need to let it air dry for 6 months or so  - depending on where you live - and then take it to the kiln. I have walnut stacked and stickered outdoors that's been there over five years. When I have room,  I bring some into the shop and let it gently dry until it reaches approximately 8% moisture content. In my part of the country (Missouri) 14% moisture content is about the best I can get drying outdoors.

+1 to the above advise.... 4/4 takes about a year to be almost dry enough to use.  8/4 will take 2 to 3 years to get to the same as the 4/4.  But even with that, your best bet, is to allow whatever size you settle on, to let it air dry for 6 months to a year, then finish it off in a kiln.  Determine the sizes your going to mill it to, and make sure you have a "flat" place to leave it, but make sure you sticker it and put some weight on it to help maintain the flatness.. If you don't do that, you'll have cupped and curled wood, and very pretty firewood!

+1 for 8/4, it's the most useful I feel as it can be resawn on your bandsaw and you can make it whatever size you need. I would look into getting it kiln dried after it has been sawn and it's ready.

+1 on 8/4 as you can get a lot of useful pieces from that thickness providing it has been dryed ok (little cupping or twist).

6/4 can also be useful too as you can get finished 5/8" book matched boards (ideal for raised panels in frame doors). It depends if you have a decent resawing bandsaw though. See if your local sawmill has a kiln they can let you dry your boards. It's much better getting heat to kill any bugs rather than leaving them to air dry. Nothing worse than seeing worm holes appear 5 years after you've made something.

I think if walnut is air dried then kiln dried on a normal cycle it doesn't change much. Commercially kiln dried walnut is steamed, which is supposed to even out the color and color the sapwood somewhat. The downside is it loses those rich purpleish variations and turns a kinda muddy brown.

I think if walnut is air dried then kiln dried on a normal cycle it doesn't change much. Commercially kiln dried walnut is steamed, which is supposed to even out the color and color the sapwood somewhat. The downside is it loses those rich purpleish variations and turns a kinda muddy brown.

Yup, I've used both air and kiln dried local walnut and both have the purples, reds, and silvers. Steamed kiln dried turns it shades of chocolate.

Branches won't make good lumber, but they can be turned on the lathe. Crotches on the other hand can yeild some spectacular planks.

It's important to seal the end grain soon after its cut to slow excessive drying and cracking. Moisture can come out the end grain too fast and lead to problems.

  • Author

Thank you for all your replies. If yo say 4/8 I assume you mean 4"x8"? The tree trunk is about 1 1/2' - 2' diameter. Some usable branches but most of them are not very straight and not very thick. Thanks again.  

4/4 = 1 inch   5/4 = 1 1/4 inch  6/4 = 1 1/2 inch  8/4 = 2 inch..etc, etc, etc.

I would probably mill it about half and half into 8/4 and 5/4, and out of whatever was left over I'd try to get some chunks of 12/4 and 16/4 that were hopefully long enough to become legs...eventually...a decade from now.  Or for turning stock if you're a greenwood turner.  The reason I'd go with 5/4 instead of 4/4 is because most of the "home-dried" lumber I've seen is warped and bowed considerably because people aren't able to stack enough weight on top of the flitch to keep it flat.  A big, warped 4/4 board is essentially worthless unless you're planning to cut it into small pieces before milling.

 

And to add to what others have said about the color in walnut...it's a common misconception to think that kiln drying takes the color out of walnut...it does not.  It's the steaming that changes the color, and makes it quite ugly if you ask me.  It basically cooks the sugars in the wood and makes the sapwood darker (and the heartwood lighter and lifeless), effectively fooling neophyte woodworkers into thinking they're getting all heartwood instead of a mix of heart and sap.  Kiln drying does NOT have the same effect, and just because a board has been kiln dried doesn't necessarily mean it's been steamed.  Kiln drying will, however, slightly toughen the wood fibers, which is why hand tool users will say they prefer air dried stock.  But depending on where you live, you often can't get lumber down to 8-10% by air drying alone, and that's the moisture content needed to safely build without major movement issues.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.