Recommended Posts

Posted

Ya I was wondering about the SS dust collection. Does that overarm dust collection get in the way ever? Do you have to remove it when using a dado set? How much dust does it save if you have a proper dust collection setup in the bottom port? With my saw now I don't really get that much dust on top with my DC setup. Also. On the topic of the mobile bases. Is the integrated one fine? Will it last a long time or should I look into the actual mobile base?

Posted

Yes, you remove it when making a dado cut.

The overarm collects all the fine dust.  You might not see it when only connected to the bottom port, but it is there.  I use my festool vac on the overarm port and my DC on the lower part.  Shop vac/dust extractors do a better job with fine dust.  

good call using the CT on the overarm - never thought of that. I agree with Mike - the overarm isn't something you want to go without. 

As for mobile base, unless they've changed something recently, there is no integrated mobile base. There are two mobile bases you can buy. The regular one and the industrial one. Which one you go for depends on how often you'll be moving the saw. If you're gonna put the saw together, move it to its final location, and then move it once every so often when you do shop reorgs, the regular one is fine. If you're moving it any more often than that, you should pay up for the industrial one. It's night and day. 

I have the regular one on my PCS, and moving it is annoying. But I don't move it very often so I don't care. If I did then I would've paid the extra $100 or so for the industrial base. 

Posted

RE overarm dust collection; rather than get it from SS, I just dropped a hose from the duct, which is already overhead above the saw. Works great.

this is what I'm planning to do - any secret parts you ordered to do it?

Posted

RE overarm dust collection; rather than get it from SS, I just dropped a hose from the duct, which is already overhead above the saw. Works great.

Yea, I did the same thing

 

this is what I'm planning to do - any secret parts you ordered to do it?

I just added a wye that had a 2 1/2 of shoot, 10 foot of 2 1/2 inch flexible hose, get the good stuff, I think I ended up using 6 feet (used the other 4 feet on my router table) and then I found a reducer a woodcraft that went from 2 1/2 to 1 1/4 or something.  I did have to put a few wraps of electrical tape to get the fit snug in to the blade guard but I can still unplug it when I have to.

  • Like 1
Posted

The PCS, like any other cabinet saw, has a cabinet mounted trunion. This means better vibration absorption and easier alignment. Space is tight in my shop, so having the four-wheel swivel of the industrial base was important to me. Sent from my iPad using Tapatalk

Posted

I think everyone has covered the facts between all the saws you are considering, so I will throw my empirical hat into the ring for your consideration. Ive had a jobsite saw(the popular dewalt model on amazon), a contractor style table saw(delta 34-444, I believe) and now a new 3hp baldor motor in a 15 year old unisaw all within the past 18-24 months. Don't even consider a jobsite saw. I had my dewalt for 2 months maybe and it really limited my quality of work. Now here is where I might get blasted, but the step up to the delta contractor saw with unifence was insane. First, it weighed 10 times as much as the dewalt. Much larger cast iron table and extension table. Fence was night and day different. Power wasn't comparable. Aligning a contractor saw is an exercise in patience, but spend $15 on the PALs alignment system, and it isn't painful or time consuming anymore. my contractor saw cut less than 1" thick material equally as well as my unisaw. It was an accurate saw and the ease of cut on 3/4" ply is indiscernible between the two saws. I might say dust collection was better on the contractor saw versus the unisaw. Both have/had retrofitted 6" ports attached to a 1600cfm cyclone. Contractor saw's port was 3-4" below the blade. The unisaw's port is over the hill and through the woods away from the blade. I have minimal saw dust build up in the cabinet, but I would prefer the port to be closer to the blade. All in all, I think you can do nice work with a contractor saw--the right contractor saw. I had the receipt along with all the manuals and crap when I bought the 34-444 used off a guy. It was $900+ back in 1993 when it was purchased. Run the numbers, that saw was freaking expensive in today's dollars.

I don't think a cabinet saw is as impressive as what everyone builds it up to be. Yes, the power is very noticeable in 1-2.5" thick material. I would go as far as to say "safer". The unisaw seems to power through wood tension instead of bind up and kickback like my contractor saw. This means less burning, faster processing etc etc. It holds its settings far better than the contractor saw. I would recalibrate my contractor saw monthly and it would consistently be out by 3-5 thous. The unisaw hasn't changed a bit since I set it up in august/july. The saw's size is nicer, but not a game changer. There you have it, all of my 2 cents.

 

Posted

One note about contractor saws, at least the older, "non-hybrid" dezigns; the motor hangs out the back side. That means the whole back is open, so airflow is less than optimal for dust collection. I also means that the motor can rise above the table when the blade is tilted to 45*, possibly interfering with the cut. At least that is how my old Rigid works.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 39 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined