Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing two sides

Featured Replies

Is there a secret to finishing a panel or a frame or something? I decided that since I wasn't in a hurry, i'd finish the top of a panel and the sides. Put 2nd coat on. 3rd day, I flip it over to the do the top of the panel and it had dripped around and pooled underneath. I had it sitting on saw horses. I'm surprised that it can even do that. I would have thought drips would fall right to the floor instead of going underneath the panel. Am I just sloppy and this will get better? I had the same problem with the frame I made a few months ago and on that, I had to sand it down and try to repair the finish. On this smoker cart panel, eh, it's going outside anyway so I doubt it looks flawless for too long. 

Also noticed that I appear to suck at sanding, and there were tons of defects in the top that I couldn't see before i put finish on (it's cedar so as you might expect, it dings up fast.)

 

Cliff, I'm assuming you applied with a brush. I've found your problem to be true if you apply the finish to the edges either in a side to side stroke or an up AND down stroke. It needs to be applied in a down only stroke, thus leaving any excess on the top surface where you can brush it out

  • Popular Post

Two things.. 1 your putting the finish on to thick. 2 finish the whole piece (section) at once. Do the side thats not showing first, then the show side. You can catch any drips from the side not showing when you flip to the show side. By that time the edges are done and you don't have to touch them so you won't introduce drips on the side you just did. Use pyramids or small blocks to raise the piece when you flip it. 

Sanding comes with time. You now know you need to look at it under better light and more closely. 

Edited by Janello

And always brush from the middle to the edge, if you start at the edge you will get drips. 

  • Author

I used a foam brush. Teak oil. So no ARS on outdoor thing. I do have wiping rags, but I kinda followed marc's finishing procedure with the Rustic Outdoor Table build. He used a foam brush, so I did too. 

Some good advice though guys. I was going back and forth and kinda all over. And I was going very thick with it because it absorbs and then supposedly you keep applying. Like.. brush on, if it drinks it all up, apply more, and then wait and wipe excess off. 

My reasoning on not flipping and doing both top and bottom in one go is it's 5 foot long. Thought it would be a big pain. But if that helps me then I'll have to keep that in mind. 

The sanding thing will be interesting because the lighting in my garage still sucks until I get a ceiling up and put the other 4 lights in. But down in the basement where I put finish on this - there is a fluorescent light directly on top of where I am. I'm glad this is an outdoor project that will get beat up or I'd be super annoyed at how crappy it looks to me :)

I bet it looks fine! We're all too hard on ourselves, and well we should be!

  • Author

Cliff, get a mechanic's work light, or a cheap clamp light from HF, and shine it at a low angle across your work piece to highlight defects, scratches, etc... Direct overhead light hides a lot.

OK. That makes sense. I'll pick one up. :)

 

I bet it looks fine! We're all too hard on ourselves, and well we should be!

That whole strive for perfection thing that Eric mentioned. I think overall it will end up looking pretty ok. If the finish is jacked up a little - well who cares, it's about to have 3 months of snow on it :)

I used a foam brush. Teak oil. So no ARS on outdoor thing. I do have wiping rags, but I kinda followed marc's finishing procedure with the Rustic Outdoor Table build. He used a foam brush, so I did too. 

 

what kind of teak oil?

Be aware, there is very little, read as no actual  teak oil in that. It is boiled Linseed oil with resins added to form a film finish. I made the same mistake expecting it to be a low maintenance actual penetration oil that help with weather protection.  Dead wrong. For me it was high maintenance and looked cheap as hell.. 

  • Author

cliff I think watco is a oil varnish blend.  You need to wipe of all excess after a few minutes, including the underside.   for any oil finish that is not straight varnish it is good to wipe off the excess.  I think Watco tells you this on the can.  

Yup I do wipe it off. I didn't wipe the bottom off though cause it wasn't supposed to go on the bottom. Cause my technique is not so good yet.

 

Be aware, there is very little, read as no actual  teak oil in that. It is boiled Linseed oil with resins added to form a film finish. I made the same mistake expecting it to be a low maintenance actual penetration oil that help with weather protection.  Dead wrong. For me it was high maintenance and looked cheap as hell.. 

I'm thinking of going over the top of it with marine varnish next year. I wrote in to the podcast asking about that a few months ago and Marc said that should be fine. Do you agree? I have to admit, I see your point with the looks. I'm not overly pleased. If I hadn't had done the base of the cart in this already, I would not have used for the top. 

What else would you recommend, just out of curiosity? 

Yup I do wipe it off. I didn't wipe the bottom off though cause it wasn't supposed to go on the bottom. Cause my technique is not so good yet.

 

I'm thinking of going over the top of it with marine varnish next year. I wrote in to the podcast asking about that a few months ago and Marc said that should be fine. Do you agree? I have to admit, I see your point with the looks. I'm not overly pleased. If I hadn't had done the base of the cart in this already, I would not have used for the top. 

What else would you recommend, just out of curiosity? 

I don't know anything about the project, the final location, or anything. That grossly under qualifies me to make a recommendation.  That and that I suck at finishing..

I don't know anything about the project, the final location, or anything. That grossly under qualifies me to make a recommendation.  That and that I suck at finishing..

What did you do the jewelry box in? That didn't suck.

  • Author

Well my theory is to cover the teak oil finish in a coat of glossy epifanes and two coats of matte. Next year though. Too cold to do it this year.

This will be outside in IL year round. So snow, -20f, rain, 105f, 100% humidity, and probably 6 or more hours of sun per day. A mix of all that. 

I think whatever I do end up with will be fine. This is my first halfway big project and I am just happy it hasn't burst into flames or exploded. Anything above that is a total bonus.

What did you do the jewelry box in? That didn't suck.

the he mahogany one was ars satin, 3 coats. The wenge and curly maple was blo under wax.

 

I use architects style lamps from IKEA, the swing arm adjustable type. I think they are $15- 20 each. Compact flouresent floodlight bulbs work but are slow to warm up. LED floodlight bulbs cost as much as the lamps do and they are heavy, I replaced the springs with stronger ones from the hardware store. They had a kit with a selection of springs. Another upgrade for these lamps is to fit a section of dowel inside the tubular section that fits inside the base, this keeps it from bending. The base can be clamped to a table top or screwed to a wall or counter surface.

i have bought higher priced lamps like this and they are not much better. The ability to aim a light across the surface being finished makes flaws visible before and after finishing. Graduating from a brush to a spray gun will help and also add a whole new set of skills to master.

  • Author

Epifanes is a great finish but not for the faint of heart.  I did an outdoor table and i took 4 coats before it started to look good.  I ended up with about 7 coats.   took 2 weeks to finish, brushing on a coat every day or two.  

Sounds terrifying. :) And sounds very expensive. That may actually be too good of a finish for my project

An almost universal rule in finishing is to use thin coats applied in a careful, controlled manner.  It's always tempting to glop on lots of juice because you think it'll speed up the process, but in reality you're taking one step forward and two steps back because of the mess it makes with drips and runs and it also slows down dry times and the curing process.  Especially with an oil/varnish blend like teak oil...too thick of a coat can take many many days to dry.  I've made that mistake myself.

An almost universal rule in finishing is to use thin coats applied in a careful, controlled manner.  It's always tempting to glop on lots of juice because you think it'll speed up the process, but in reality you're taking one step forward and two steps back because of the mess it makes with drips and runs and it also slows down dry times and the curing process.  Especially with an oil/varnish blend like teak oil...too thick of a coat can take many many days to dry.  I've made that mistake myself.

Same here.  My go-to finished used to be Watco Danish Oil, mostly because it's easy to apply.  Put on a way-to-thick coat on one project and after three days it was still tacky (and it looked terrible).  Ended up sanding it back and, many sanding pads filled with gunk later, reapplying in thinner coats.  Lesson learned.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.