collinb Posted October 7, 2016 Report Posted October 7, 2016 New-to-me power toy / tool. I have always had an affinity for mid-range tools. Cheap used and quality more than enough. Have trailing edge snipe. Probably outfeed adjustment. A little more studying, a little more practice. Tomorrow to buy some locking wheels ... I actually bought 2 of these this past week. The other (orange base version) to part out, has a broken infeed. Too broken to repair. Might be nice for someone who wants to build a parallelogram jointer. Just build the beds. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
Brendon_t Posted October 7, 2016 Report Posted October 7, 2016 Yeah that's some really bad snipe from a jointer. Have you raised the outfeed? Quote
collinb Posted October 7, 2016 Author Report Posted October 7, 2016 Yeah that's some really bad snipe from a jointer. Have you raised the outfeed? Will next time I use it. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
Brendon_t Posted October 7, 2016 Report Posted October 7, 2016 Ok then. Having to stop a project to set up a tool I left out of whack would tick me off but more power to ya Quote
collinb Posted October 7, 2016 Author Report Posted October 7, 2016 Ok then. Having to stop a project to set up a tool I left out of whack would tick me off but more power to ya I just got it late last night. I don't do this full time so there's no interruption to any project. And a dedicated block of time for final setup is more my approach anyway. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
sjeff70 Posted October 7, 2016 Report Posted October 7, 2016 5 minutes ago, Mike. said: Some of those Ridgid machines were/are relative gems, from what I understand. Unfortunately I don't think the market for them every really developed. Exactly. Collin, I'm interested in seeing the results when you get it dialed in. Quote
BonPacific Posted October 7, 2016 Report Posted October 7, 2016 Other than the snipe, looks like a nice new toy. When I first got a jointer I had similar problems with snipe, found it was my technique after some practice (and a lot of ruined boards). Using push-pads made a huge difference for me over hand-feeding. Quote
Coop Posted October 7, 2016 Report Posted October 7, 2016 The problem could be that you are applying downward pressure on the tail end of the board just as it's getting to the cutterhead instead of applying it on the out feed side. 1 Quote
Chestnut Posted October 8, 2016 Report Posted October 8, 2016 Hey that looks better then my jointer. I have a craftsman jointer from the 1980s. These small unites are nice but they are just that, small. I want something larger and with a HH but space doesn't allow for it at the moment. Nail technique and make sure it's all adjusted. My jointer looks like a pile but actually works decently well. Quote
collinb Posted October 8, 2016 Author Report Posted October 8, 2016 2 hours ago, BonPacific said: Other than the snipe, looks like a nice new toy. When I first got a jointer I had similar problems with snipe, found it was my technique after some practice (and a lot of ruined boards). Using push-pads made a huge difference for me over hand-feeding. I did use push pads. Wouldn't use a jointer without them. It's almost definitely the outfeed. 2 hours ago, K Cooper said: The problem could be that you are applying downward pressure on the tail end of the board just as it's getting to the cutterhead instead of applying it on the out feed side. Pressure was only on the outfeed side when exiting. 1 Quote
bleedinblue Posted October 8, 2016 Report Posted October 8, 2016 I have the orange version of that jointer. Snipe isn't too bad, but I tend to get quite a bit of wash boarding. Maybe feed rate, maybe dull blades? Regardless, it's a pretty decent jointer I think. Quote
Ronn W Posted October 8, 2016 Report Posted October 8, 2016 I am going to guess that your outfeed table is lower than the blades by a few thousands. Quote
collinb Posted October 8, 2016 Author Report Posted October 8, 2016 Got some time this afternoon and got it adjusted. Smooth as silk. No chatter. No snipe. Sent from my MotoE2(4G-LTE) using Tapatalk 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.