Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Sand or something else?

Featured Replies

First, thanks for your suggestions.  I have attached a picture of a Cherry coffee table top that needs some attention.  It was finished with Watco Danish Oil many years ago and maintained with occasional wax.  As you can see there is some water damage.  The water damage is not recent - been there for several years.  Should I sand or try something else first?  I plan to refinish with Waterlox to add protection from water damage in the future.

Cherry Coffee Table Top.jpg

If a sander is in your stable of tools, have at it. There are other options but if you're comfortable with that, get at er.

Sharpening a cabinet scraper does have a learning curve but a Watco finish will clog many sheets of sandpaper quickly . Learn once or buy abrasives far more often !

My approach would be to wipe it down (aggressively) with mineral spirits to clean off all the wax.  Maybe even scrub a bit with a non-woven pad and mineral spirits.  Be sure to get all the nooks and crannies.

If the surface was then as I expect, I would use a card scraper to lightly shave the surface to get an even appearance.  I don't often advise a ROS but, once you were at this stage, the random action with a hard pad and a finer grit would probably get you to where you want to be prior to refinishing.

There's always more than one way to skin the cat.

Chemical strip with a good stripper containing methylene chloride. Get it on with a brush and scrub with the grain using steel wool. Once the finish and wax is removed, go with the grain with dry steel wool to (sand) for lack of a better word and remove any dried finish.

Wash the wood down with mineral spirits let it dry a day or so. Sand as you normally would. Then apply your finish schedule.

 

-Ace-

 

Remember to follow safety direction, wear safety equipment and use in well ventilated area. 

 

 

  • Author

Ace - thanks for the suggestion.  Since Watco mostly goes into the wood and does not sit on top, can you educate me on your suggestion to chemically strip?

Honestly, I think chemical stripping will be overkill. Most oil finishes sand back pretty easily. Certainly try just cleaning with mineral spirits or naptha & then sanding. If that doesn't do it, then try the stripper.

6 hours ago, NoCLue64 said:

Ace - thanks for the suggestion.  Since Watco mostly goes into the wood and does not sit on top, can you educate me on your suggestion to chemically strip?

The stripper is based in a gel compound to slow the flashing off of the chemicals. Thus allow deep penetration into the wood. However, topcoats over a stain and stains contain a binder. So think of it as peeling an onion. First coat of stripper usually removes the topcoat. The second coat usually removes the stain layer. A third coat takes you down into the wood. A word of caution, you will never get the "color" completely out of the wood. So the notion of a clean white wood is nonsense, but you don't need to either, although you can get pretty damn close.

I see a lot of poor stripping jobs. Folks stop to soon and you see what looks like blotching. Areas of clean and dirty wood. Your final coat should be really wet  with stripper let it sit then scrub with the grain. Once your happy and everything is even wood color take clean steel wool and scrub the wood with the grain remove any dried trace residue in the grain, this also will help to even things out.

Most issues is folks  go to light with the stripper, they want to make it last. So wet,wet,wet and keep it wet. Once the stripper has flashed off dried and you don't get it removed. All your doing is melting the old finish back into the wood. The steel wool will fill with old finish, so have plenty on hand. Use coarse steel wool.

You have a thin oil finish so not that big of deal.

-Ace-

 

 

 

    

 

 

  • Author

Not done but here's an update.  I don't pass up many opportunities to buy a new tool and learn how to use it.  Ps:  the burnisher from Veritas is OK but I got better results from a hardened steel cabinet screwdriver.

IMG_2580.JPG

IMG_2584.JPG

IMG_2587 (1).JPG

  • 3 weeks later...
  • Author
  • Popular Post

And here's the final result.  Yes, it's too darn shiny but I am going to wait and see if it grows on me for now.

016079936c8d2ee3bbe812f7f1edcad205ece6c531.jpg

Or if you don't like it so shiny, just add a coat of matte. You did a great job there.

A red or grey abrasive pad will knock the gloss back pretty quickly . Green = extra coarse, red/maroon = coarse, grey = medium , white = fine  . It's the modern day equivalent to steel wool. Scotchbrite is one brand. It's available in the paint department of any big box store.

That's great, Steve - a real public service!  I blush to admit that, while I possess and use all colors, I hadn't yet sorted out the color coding :-0

She looks great.  Congrats on the result and on picking up some new tools / skills.  Let the finish grow on you awhile, you can always knock it back a bit if it proves too much.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.