Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Beginner finishing question

Featured Replies

Hi, 

New to woodworking. I built a small side table and have been researching how to finish it. I am sure there will be glasses and things put down on the top. despite best efforts I also know that coasters will likely not be used. I have heard that Arm R Seal is a good product. I have searched the forums for my specific question and despite healthy discussion have not been able to find the answer.

The table is small with lots of parts. 9 rails to be exact and a floating top. I like to complicate things.... So I am worried that if I also try to put Arm R Seal on the base it will run and come out looking streaky. Should I use a different finishing method for the table base? Do you generally use Arm R Seal on vertical legs as well without runs?

Thanks for the Help! Hope this isn't too redundant of a question.  

welcome to the forum Felix, ARS can be applied with a clean cloth (think cut up t-shirt) if you're worried about runs, its pretty thin so adjust accordingly, i most often use a good quality foam brush. 3 coats should protect it from any water marks just be sure to let it dry for a couple of weeks before setting anything on it, be sure to post some pictures and again welcome, this is a great place to learn and share.

Like Dave said ARS is a good way to go.  Just wipe it on with a clean cloth.  Also pour a little at a time into a disposable secondary container, don't dip you cloth in the the can itself this way you keep you unused finish in better shape.  Just wipe it on and leave it alone, don't keep messing with it.  And you will be way better off by building you finish with several thin coats instead of a couple of thick coats.  Trying to get it on to heavy is were you start having a run problem.  The wood will probably suck up the first coat pretty good.

Welcome to the forums Felix.

Hi Felix - Eric posted a good summary of his finishing schedule using ARS here:

 

Hi Felix. There is nothing easier than a wipe on finish and ArmRSeal is one of the best - sadly I can no longer get it in the UK and I am on the last few cans. Prepare the wood by sanding to 180 grit first of all and maybe go up to 220 or 360 for any exposed end grain. Don't worry about non show surfaces as they don't need as much attention.

Apply ARS with a cloth folded into a pad. Reapply until the surface is flooded, wait a few minutes for it to soak in and wipe off the excess - on the very first coat the raw wood is very thirsty so will take in quite a bit of finish. Wait overnight for it to cure and very lightly sand to key the next coat. Apply 3 more coats to all surfaces including verticals, again wiping off excess waiting overnight and sanding very lightly (800 grit wet and dry works great). Apply an extra one or two coats to the top as that will get the most hammer.

Wait a week or so after the final coat is applied to cure and remove dust nibs with 4000 grit sanded wet (mineral spirits or just water to lube). Finish with a brown paper grocery bag (seriously) and it will be baby butt smooth.

Welcome to the forum.

  • Author

Hi Everyone-

 

Thank you first of all for the warm welcome! I have read many woodworking forums but never participated and so glad I did!

It seems like there is more than one way to skin a cat, but the basic principals are the same. I will give it a whirl and hopefully have some pictures to share by the end of the week!

Thank you again!

For all of the parts except the flat horizontal surfaces I use a rag to appy ARS - wipe on and gently wipe off.  Each coat is very thin os plan on several coats.  for the horizontal surfaces I apply ARS with a sponge brush.  Spread it all arounds quickly (don't worry about the grain direction) and check for any missed spots.  YOu don't wnat it thick just thin aand even.  Then make full length stokes with the grain overlaping each stroke with the previous one.  If it appears that there is too much ARS being pushed by the brush at the end of a stroke, daub the excess off on a rag and keep on going.  Be sure to cath any drips around the edges.  Maybe 2 or 3 coats this way with very light sanding in bewteen with 400 grit to knock off the dust nibs.

  • Popular Post

A good habit to have is plane, sand and prep some scraps along with every project. Use them to test finishes on. Then you can test for dryness on the scrap and not leave fingerprints on your project. If you make a mistake while finishing you can practice the repair on the scrap first. This also gives you finish samples, write the steps and products used on the back with the date.

  • 2 weeks later...

Im just a novice learning what I can. Is this basically like midwax wipe on poly but better quality? Ive been using the midwax poly on shelfs made from and like it but doubt its ability to hold up to condition from cups and wanted to make a coffee table. Sry to but in the thread didn't want to start another thread for a simple question.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.