Popular Post Steve B Anderson Posted May 20, 2017 Popular Post Report Posted May 20, 2017 This is my first attempt on a furniture project and it has been a learning experience to say the least. I purchased a table saw, bench top planer and a drill press to get started. I did not plan on making a journal of this project at the start so the wood preparation steps are not documented. After some encouragement from Mr. Cooper and many other members here I started documenting my progress which started about half way into the M&T joint process. I would like to share my first experience with the planer. After researching online about planers I know I would need a sled. That was simple enough to make and turned out well. I loaded my first board, shimmed were needed as I was ready to go with all the confidence in the world, but when I fired that bad boy up the hair stood up on the back on my neck. Now I was a machinist for many years and I am not easily intimated by any machine but this thing scared the crap out of me. I shut it down, checked the height setting again but still didn't have the nerve to push it through. I ended up cranking the handle up a couple a turns and made three runs slightly lowering the head until it started cutting. Now after about 30 board feet later I'm very comfortable with it but I will always remember that first board. After the prep work, I started on the mortise and tenon joints, another first for me. I uses a router table with a 1/4" up spiral carbide bit to cut the mortise. My table is too small to setup stops so I marked both sides on the bit on a piece of tape, transferred the mortise lines around the legs, plunge and feed to the lines. And yes that is a 30+ year old Craftsman router table. I use this adjustable parallel to set the fence (old machinist tool). I set the parallel with a micrometer, lock it down and set the fence. More to follow. 8 Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 Thanks Micks, the most frustrating part is getting the pics sized. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 Tenon Joints I had already cut these before anticipating the journal. I made a cross cut sled and use a dado blade on the table saw. I wasn't sure how this was going to turn out so I cut the thickness and width heavy. Used a chisel and file to hand fit each joint. Next time I will at lease cut the thickness to size. More to follow Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 Tenons done now its time for the floating panel slots. This is where my first mistake happens, not a bad one but still a mistake. I had milled the thickness of the wood heavy planning on sanding to size. I did not take this into account when setting the location of the slots. I set my fence at a 1/4" and made sure I put the outer showing faces against the fence so I would have a constant reveal on the outside of the piece. Well I accomplished that but the slots were not centered on the boards as planned. Lesson learned. More to come Quote
Popular Post Steve B Anderson Posted May 20, 2017 Author Popular Post Report Posted May 20, 2017 Slots cut now its time for a dry assembly of the frame. Oops I did the assembly before the slots. All of these operations were done before I started the journal so I'm trying to piece them back together. I was a little worried but everything went together as planned! Yes! I was happy! 3 Quote
gee-dub Posted May 20, 2017 Report Posted May 20, 2017 Looking good Steve. Thanks for taking us along. There are others but, I use PixResizer to resize pictures in batches. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 After the frame assembly I cut the slots for the panels as seen above. I then took measurements from of the frame and cut out the panels from the 4 x 8 sheet. I did not document this process but it was completed on the table saw. I then did a dry assembly of the sides. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 4 minutes ago, gee-dub said: Looking good Steve. Thanks for taking us along. There are others but, I use PixResizer to resize pictures in batches. I've got it figured out now using paint. Just had to find the right size. Thanks for the tip and thanks for the good comment. It means a lot coming from someone with your experience. Quote
..Kev Posted May 20, 2017 Report Posted May 20, 2017 Looking awesome! Well done! Just a suggestion, you might consider flipping those panels around so that the cathedrals point up. Nit picky detail and just a suggestion to the fine work! 2 Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 Finishing Time Everything fits together so on to the finishing chores. I call it a chore because it is my least favorite process. Waiting on stain/dye and top coat to dry is about as exciting as watching grass grow. But I am happy that things are now in the final stages and are getting closer to final glue up. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 6 minutes ago, TIODS said: Looking awesome! Well done! Just a suggestion, you might consider flipping those panels around so that the cathedrals point up. Nit picky detail and just a suggestion to the fine work! Thanks for the great tip Tiods, I have to agree. I will do as you suggested. Quote
Guest Posted May 20, 2017 Report Posted May 20, 2017 Looking good. It looks to me like your machinist training is paying off. You seem to be working with precision and patience, which is about 90% of the battle. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 This is a fixture I made for finishing the legs, 16D nails as centers and rotate as needed. 2 Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 5 minutes ago, Mike. said: Looking good. It looks to me like your machinist training is paying off. You seem to be working with precision and patience, which is about 90% of the battle. I have had to use all of my machinist skills on the project. Quote
Steve B Anderson Posted May 20, 2017 Author Report Posted May 20, 2017 Finishing Schedule I have never used anything other than stain in my wood projects and at this time it is the only medium I am comfortable with. I have projects on the board that I will be experimenting with the Mission finishing technique, but for my first project I wanted to stay with something in my comfort zone ( The wife wanted Gunstock 231 for her bookcase so I had to roll with it). The next project is mine so dye and gel stains are in my future. I started sanding through the grits, 100, 120, 180, 220. Preconditioned with Minwax Pre Stain. To my surprise, this bleed out of the pours for 30 minutes so I had to constantly wipe it down until the bleeding stopped. Then stain with Minwax Gunstock 231. Wipe on and wipe off no soak time. This also bleed out of 30 minutes are more so constant wiping was required. I don't have pics but I put two coats of Zinsser 2lb cut non wax shellac seal coat on over the stain and that really made the wood glow. I don't think pictures could do it justices but it really enhanced the grain and gave it depth. I'm in the process now of wipe on poly. I thinned full strength 2:1 with mineral sprites and using folded paper towel for an applicator. Sanding between coats lightly with 320. Should be ready to glue up the sides with Tight Bond III in a couple of days. I'm using Tight Bond III because it has a longer open time than the others and I will need that when assembling the sides to the rest of the frame due to the back panel installation time. Please comment on this because I am just making an educated guess. 1 Quote
drzaius Posted May 20, 2017 Report Posted May 20, 2017 You're doing some quality work there. I like that adjustable parallel & can see one of those as part of my tool set. Never even knew they existed until now. Quote
Dknapp34 Posted May 20, 2017 Report Posted May 20, 2017 Looking good! This is miles ahead of how my first project looked. My first tenons were some ugly looking things that I cut with a cheap hand saw from HD. Looked like the dog chewed on them. The machinist training sure makes a difference. Sent from my iPad using Tapatalk Pro Quote
Eric. Posted May 20, 2017 Report Posted May 20, 2017 You're doing extraordinarily clean work for a first project. A meticulous nature can take you a long way down the road in this sport, even if you're lacking in the talent department (DAMHIK). Well done, Steve. Quote
wtnhighlander Posted May 20, 2017 Report Posted May 20, 2017 Good thing about coming from the machinist world, is you already undestand precision, and the value of jigs & fixtures. That puts you way ahead of the average Joe off the street. This project is looking great. Regarding the finishing process, you will soon discover that a large number of us lean toward choosing stock to exhibit its natural color and grain, so staining is often left out. However, there is plenty of knowledge about the process, so any questions you have will surely get a good answer, or three! 1 Quote
gee-dub Posted May 20, 2017 Report Posted May 20, 2017 9 hours ago, Steve B Anderson said: To my surprise, this bleed out of the pours for 30 minutes so I had to constantly wipe it down until the bleeding stopped. I made the mistake of doing an oil flood technique on red oak once. I had to continue to wipe it down for three weeks as it kept on weeping. Your golden color is looking good. Ever onward . . . 1 Quote
Eric. Posted May 20, 2017 Report Posted May 20, 2017 I'm a little surprised to hear that the sealer wept for so long...those are usually fairly quick-drying formulas. I'd go a little lighter with the coats in the future, especially on open-pored species like oak. Quote
wdwerker Posted May 20, 2017 Report Posted May 20, 2017 It was the stain that kept bleeding out of the oak pores. He had no complaint about the shellac weeping. I think Minwax stains are really not that great but most of the stuff I use isn't available at a big box store. Eric is right about thin coats being better for stains, sealers and finishes in general . There are exceptions but that's another conversation. Thanks for posting your journal of this project ! It's looking far better than some of my early work , but I was a teenager and ignored instructions... Quote
Eric. Posted May 20, 2017 Report Posted May 20, 2017 8 minutes ago, wdwerker said: It was the stain that kept bleeding out of the oak pores. He had no complaint about the shellac weeping. 10 hours ago, Steve B Anderson said: Preconditioned with Minwax Pre Stain. To my surprise, this bleed out of the pours for 30 minutes so I had to constantly wipe it down until the bleeding stopped. Maybe I'm confused but it sounded like he was talking about the sealer. Quote
wdwerker Posted May 20, 2017 Report Posted May 20, 2017 I was told that Minwax pre stain is all the basic ingredients of their stain but colorless. I think we're calling different things "sealer", that's what I would call the shellac coat. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.