Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Wood bending

Featured Replies

I am more and more interested in bending wood! I am in awe of this table and similar projects and am wondering: how can this be done? I assume there is different ways!? 

IMG_7063.JPG

It looks like that could have been made from bendable ply.  Sometimes the bends are just creative ways of doing joinery, I think Kyle Toth did something similar and the way he joined them was what created the bends.

  • Author
57 minutes ago, wtnhighlander said:

IIRC, Toth used a combination of 'bricking' and bent lamination, with a final surface lamination.

Thanks for your reply but can you explain just a little more what bricking and bending exactly look like / mean?

  • Author
8 hours ago, Woodenskye said:

It looks like that could have been made from bendable ply.  Sometimes the bends are just creative ways of doing joinery, I think Kyle Toth did something similar and the way he joined them was what created the bends.

Thanks much! Using bending as a creative way of doing joinery... I am not knowledeable enough to know what that looks like. Can you explain? Thanks!! 

  • Author
23 minutes ago, Gixxerjoe04 said:

 

Great video! So the question is: what did he roll on the single planks before clamping them around that mold? was this glue or rather ammonia? What made it bend? Thanks for the link! 

44 minutes ago, Onlysardegna said:

Thanks much! Using bending as a creative way of doing joinery... I am not knowledeable enough to know what that looks like. Can you explain? Thanks!! 

I have never done this either, but if you cut at certain angles, eventually you can get 360 degrees, so once you figure out the angle you are looking for, you would cut the angle and the opposing angle and join. 

Great video, but I'm not sure you should try some of those table saw tricks at home.

My guess is a vacuum bag clamped to an exterior form at crucial points. Some sort of urea formaldehyde or other ridgid laminating glue would be used. Even with a jig/form each piece would be slightly different. An odd number of layers makes a stable final product. Plywood is always an odd number of layers for balanced construction.

This is an advanced project for even the best of us !

  • Author

Thanks for all the kind and knowledgeable  answers!! I appreciate them all! This does look tricky but I will continue looking in to this! 

What he rolled on the thin pieces before clamping them together in the vacuum bag is glue.  By the looks of it I would say some kind of epoxy, but it doesn't have to be anything special.  Regular old white glue would work well.  When you laminate a shape using thin pieces (usually about 1/4" thick) and glue them together over/around a mold, once the glue sets, the piece holds it's shape.  They will spring back a little bit from the shape of the mold, but not much.  We used to make the stringers and hand rails for spiral and curved stair cases using this method.  We would use about 7 layers of 1/4" material to end up with a 1 3/4" stringer, more for the hand rail about 10 or so.  The stringers were cut by hand for the treads/risers and the hand rail was run on the shaper to put the classic hand rail shape on it.  How thin the pieces are that you are going to laminate together depends on the radius you need the wood to bend to.  The sharper the radius, the thinner the pieces need to be to bend without breaking.  One of the reasons you get into steaming wood is when you can't bend the radius you want without breaking the wood.

I'm currently helping my neighbor with cabinets for finishing his basement and one of the cabinets in the kitchen area has a 10' radius on the front.  This means that the face frame, doors and drawers are all curved to that radius.  We used the same method as in the video (although not nearly as complex) to laminate the face frame, top and bottom rails for the panel doors, and the 8" tall drawer fronts.  It's turning out nice.  We'll be hanging the doors and fitting the drawers this weekend.  The process is not hard, but it is time consuming.

It's a lot of fun and everyone always wants to know how you did it.  Start with a simple curved shape and give it a try.

White glue & yellow glue will creep/slip/move especially on bent pieces. Glues made for veneering give a ridgid glue line. The video skips crucial steps, but it's a fun overview. He also does some risky cuts and uses less than optimal joinery between the pieces. Spray can Contact cement isn't the best way to apply the finial veneer for long term success. Check out " Joe Woodworker's" web site for info on glues, tools, supplies and techniques. 

6 hours ago, wdwerker said:

White glue & yellow glue will creep/slip/move especially on bent pieces. Glues made for veneering give a ridgid glue line. The video skips crucial steps, but it's a fun overview. He also does some risky cuts and uses less than optimal joinery between the pieces. Spray can Contact cement isn't the best way to apply the finial veneer for long term success. Check out " Joe Woodworker's" web site for info on glues, tools, supplies and techniques. 

 

6 hours ago, wdwerker said:

All glues except contact glue will slip/creep.  Yellow glue sets up too fast and is too thick for anything but the most simple laminated pieces (really for any IMO).  For the piece in the video, even white glue would probably setup too fast, which is why I'm betting that he used a slow set epoxy.  We used to use a very slow setting epoxy when building cabinets with composite materials in business jet interiors (Lear, Citation, MU2, Falcon, etc.)  Some of the shapes were pretty complex and we needed plenty of time to do the assembly and clamping.  For the Stair stringers, hand rails, and many other laminated pieces I've made and the cabinet I'm currently working on white glue works great.

 

6 hours ago, wdwerker said:

White glue & yellow glue will creep/slip/move especially on bent pieces. Glues made for veneering give a ridgid glue line. The video skips crucial steps, but it's a fun overview. He also does some risky cuts and uses less than optimal joinery between the pieces. Spray can Contact cement isn't the best way to apply the finial veneer for long term success. Check out " Joe Woodworker's" web site for info on glues, tools, supplies and techniques. 

Sorry for the additional post.  I agree about the spray can contact cement and that a veneer glue is best for applying the veneer.  Happy building. . .

Where did you find this being attributed to me ?

   6 hours ago,  wdwerker said: 

All glues except contact glue will slip/creep.  Yellow glue sets up too fast and is too thick for anything but the most simple laminated pieces (really for any IMO).  For the piece in the video, even white glue would probably setup too fast, which is why I'm betting that he used a slow set epoxy.  We used to use a very slow setting epoxy when building cabinets with composite materials in business jet interiors (Lear, Citation, MU2, Falcon, etc.)  Some of the shapes were pretty complex and we needed plenty of time to do the assembly and clamping.  For the Stair stringers, hand rails, and many other laminated pieces I've made and the cabinet I'm currently working on white glue works great.

I've never worked on a Lear etc interior.  I haven't bought white glue in over a decade.

14 minutes ago, wdwerker said:

Where did you find this being attributed to me ?

   6 hours ago,  wdwerker said: 

All glues except contact glue will slip/creep.  Yellow glue sets up too fast and is too thick for anything but the most simple laminated pieces (really for any IMO).  For the piece in the video, even white glue would probably setup too fast, which is why I'm betting that he used a slow set epoxy.  We used to use a very slow setting epoxy when building cabinets with composite materials in business jet interiors (Lear, Citation, MU2, Falcon, etc.)  Some of the shapes were pretty complex and we needed plenty of time to do the assembly and clamping.  For the Stair stringers, hand rails, and many other laminated pieces I've made and the cabinet I'm currently working on white glue works great.

I've never worked on a Lear etc interior.  I haven't bought white glue in over a decade.

Fake news.

For something as complex as this glue up, slow set epoxy would also be my recommended choice. Urea formaldehyde would be my second choice, but it's urea formaldehyde. 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.