Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How to give shallac a little more open time

Featured Replies

I really like the look shallac gives to wood but on larger pieces it's difficult for me to apply it correctly due to the short open time. I am using Zinsser 2# cut wax free sanding sealer. Is there anyway to extend the open time for this product?

This is only from reading; I have no actual experience.

Your shellac flakes were presumably dissolved in denatured alcohol, if it was high quality denatured alcohol, it was (I believe) over 90% ethanol with a bit of methanol mixed in.  Both of those have a relatively short pot life.

Isopropyl alcohol provides a longer pot life, so I think you can thin the shellac with isopropyl (rubbing alcohol, as I understand) and it should have an extended pot life.

Best to check all this info (or possibly fake news) on more authoritative sources ;-)

That's definately worth a test run though.  Thin one small batch with DA, and another with IA, and compare results on a test board.    I'd be afraid of the alcohols not mixing properly for some reason.  And Iso is pretty cheap IIRC.    At the very least you can clear out the drug store like I did with mineral oil, got some weird looks from that one. 

Shellac is best looking with many many super thin coats.Unless your trying to fill pores then go heavy and wait several weeks to dry cut it back flat and polish.

The stuff in the can has its place but not for a top clear coat.

Aj

Also if you spray instead of wipe, open time is basically irrelevant.  Shellac sucks to wipe, IMO.  Unless you're trying to French polish, I'd spray it.  I know pros brush it sometimes, but that just seems like it would be a god awful mess of a finish unless you were highly skilled.

  • Author
8 hours ago, Aj3 said:

Shellac is best looking with many many super thin coats.Unless your trying to fill pores then go heavy and wait several weeks to dry cut it back flat and polish.

The stuff in the can has its place but not for a top clear coat.

Aj

I use it as a seal coat after staining. Only 1 or 2 thin coats, just enough to give the wood that glow and depth you get with shallac. I just finished a book case that has a 28" x 43" back panel and the shallac was getting tacky before I could finish each overlapping pass.

I will try the two different alcohols and see how it goes. Thanks for the tips.

1 minute ago, wtnhighlander said:

French polish technique uses oil to lubricate the applicator, so the shellac doesn't stick to it as it dries. I wonder if dampening a rag or brush with mineral oil would have any such benefit for a non-polished application?

Typically they use BLO for that.

I'd just spray it anyway.  Wiping it is insanity.  Especially a 2# cut.  Sticky horrible mess.

Typically they use BLO for that.

I'd just spray it anyway.  Wiping it is insanity.  Especially a 2# cut.  Sticky horrible mess.

Sounds like the recipe for "shine juice" that turners use. Makes sense, as they are essentially wiping on the finish at high speed.

 

I agree, spraying, at least for sealing over a stain, seems like the simplest way to go.

Personally, I enjoy wiping shellac, but I use a much thinner cut.

Isopropyl alcohol sounds like a bad idea to me. They add either castor oil or wintergreen oil plus acetone or some sort of ketone and I think most contain a certain percentage of water. Alcohol may be only 70 % of the solution.

Use a thinner cut to brush larger surfaces.

you can add a small amount of turpentine to increase open time.  I have done this, it works just fine. 

I think you can add up to 4 tbsp tbsp per quart.  

A bit more internet research:

This is one of my key resources and where I bought my (so far unused) shellac flakes:   https://www.shellac.net/alcohol.html

Note in particular that they offer a product specifically to "increase open time", called "Behlen Behkol".  Behlen Behkol is apparently just high quality denatured alcohol.

They also offer a "retarder" which they seem to indicate is N-butyl alcohol.

WRT Werker's admonition, I'll look for the source of my isopropyl alcohol suggestion,  probably best to question that for now!

 

 

 

At first it was the water that concerned me, then I read about the oils added. I was only worried about the drug store rubbing alcohol. I've used waterbourne finishes that contained N butyl alcohol in one of the additives I think.

  • 2 weeks later...

I was taught to apply shellac with a dense fine bristle brush - like a sash brush only wider so it holds lots of shellac.  I use single long strokes with the grain, no back brushing,  Each stroke overlapped with the previous.  I can get 2 to 3 24" long strokes for each dip in the shellac. Be sure not to have too much shellac on the brush.  You want a thin even coat with no puddles.  This works for flat surfaces or routed profiles.  Since you start at one edge of the table to (for example) and work toward the other, time is not an issue since the only wet edge will be covered by the next stroke. If you don't put to much shellac on the brush, it will not run so it works on vertical surfaces.  I typcally have a clean folded rag that I daub the brush on before putting the brush to the wood to remove excess shellac.  This system works great for me.

Open time simply depends of the type of alcohol you use. If you want more open time, use an alcohol that don't dry fast. You just need an alcohol above 70°. Whatever it is, it will work fine. Just the smell changes. Usually, we want alcohols that have rather a quicker drying time (IPA, for example but remember it's vapor and touch toxic). So you can apply then polish in few back and forth movements. I use what you call the French polish method (we call it the "Vernis au tampon" - literally "rag varnishing"). This is faster than spraying, you don't waste any product and you don't have a paint gun to clean. To get the same results you need to spray a lot of light passes, and you will never get the magic of the shellac. And the polish step is totally missing. The temptation is to spray heavy layers, but you won't get that expected transparency and that particular proximity feeling with the wood. And please avoid premixed spray cans, this is the worst shellac money can buy. Shellac is so simple to mix and to use, who want spray cans ?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.