Recommended Posts

Posted
Just now, mat60 said:

Thanks.     I like the trunk builds.   Is Chet trying to stay out of the video. :)

He'll show up next week ;)

We were both nearly always doing something on the build.  We'd just stop once in a while to grab a little video footage.

  • Like 1
Posted
1 minute ago, Woodenskye said:

Great start!  Another build I will be following along with.  Will you pre finish the parts?  

No.  Although not a bad idea, there just wasn't time.  

 

Posted

Kev and Chet, thanks to both of you for taking the time to video your projects. I'm sure most of us will never construct this trunk, but there are many aspects of the builds that we can certainly use in our own projects in the future. I've yet to see one from you guys that I didn't learn something. 

  • Like 2
Posted

I love those things.  The many elevations and textures appeal to me much the way A&C styles do.  This might explain my fascination with G&G.  I have a list of items I would love to make if only someone would commission them (or I had the room for them) . . . Steamer Trunk, Chimney Cupboard, Hallway/Sofa Table, a pair of glass front bookcases, the list goes on.  Lovin' the videos and project journals.  Keep 'em coming.

  • Like 1
Posted
1 minute ago, Chet said:

That was a looong day.  We started about 8 AM and you pulled out of the driveway as 9 PM was approaching.

Yes it was!  I think we were both pretty tired there at the end!

Posted

A real beauty and a 'bucket list' item for me should I ever get the chance.  There is something about a steamer trunk that just draws the eye and yours is tops.  I always appreciate the videos so that I can learn from watching your methods and approach; thanks for that as always.

As a side note, I have always hemmed and hawed about spraying since I do not have room to cordon things off.  I notice you spray right at your assembly table with just a drop cloth.  Was this an exception or do you do this regularly?  My curiosity is about the long term over-spray (minimal though it may be) settling on things over time.  Maybe it is dry enough by the time it settles to be just brushed away?

  • Like 1
Posted

Tuned out great!! Thanks for sharing.

One question I typical spray outside with my Fuji MM3 due to over spray but have always wondered if it is necessary. Does the spray atomize so quickly that it dries before it its the floor/tool/benches etc?

  • Like 1
Posted

Since I started spraying a little will back I just cover the tool surfaces and all is good.  The last time I sprayed I didn't even cover the tools that were behind my line of fire and saw no affects other then some dust that brushed away.  My jointer, planer, tablesaw/outfeed and work bench are clustered together so I can cover all that with one large painters drop cloth and this makes a nice area to lay parts out on.  I do close the garage door all but about a foot so as to not "paint" the vehicles.  I have only sprayed water bourne.

  • Like 2
Posted
10 hours ago, shaneymack said:

I just got caught up on this, Kev. It turned out amazing ! I hope you have some more project videos in the pipe

 

Something interesting coming..  Stand by ;)

9 hours ago, gee-dub said:

A real beauty and a 'bucket list' item for me should I ever get the chance.  There is something about a steamer trunk that just draws the eye and yours is tops.  I always appreciate the videos so that I can learn from watching your methods and approach; thanks for that as always.

As a side note, I have always hemmed and hawed about spraying since I do not have room to cordon things off.  I notice you spray right at your assembly table with just a drop cloth.  Was this an exception or do you do this regularly?  My curiosity is about the long term over-spray (minimal though it may be) settling on things over time.  Maybe it is dry enough by the time it settles to be just brushed away?

Normally, I also toss a cloth over the jointer as well as the bandsaws but, was lazy this time.  I only do that with WB finishes.  Anything with strong VOCs goes to the garage!  I also have the door open and a fan pulling out the door as much as I can.

 

8 hours ago, pkinneb said:

Tuned out great!! Thanks for sharing.

One question I typical spray outside with my Fuji MM3 due to over spray but have always wondered if it is necessary. Does the spray atomize so quickly that it dries before it its the floor/tool/benches etc?

I hope the answer above works for your question as well?  I've been doing it for a few years in there and haven't noticed anything on the uncovered surfaces.

 

thanks all for the kind words!

  • Like 1
Posted

Nice project, Kev. Thanks for taking us along.

It's really fortunate (for us) that you have woodworking friends all over the place.:)

I always "like" your Y-Tube videos before I watch them. I'm pretty confident that it'll be good stuff, so why not cut to the chase?

  • Like 1
Posted
1 hour ago, davewyo said:

Nice project, Kev. Thanks for taking us along.

It's really fortunate (for us) that you have woodworking friends all over the place.:)

I always "like" your Y-Tube videos before I watch them. I'm pretty confident that it'll be good stuff, so why not cut to the chase?

It's still a little premature..  If all works out as intended, we're moving.  We have a sale agreement on the current house and will be making an offer tomorrow on the new house which is in Montana.  A lot of things have to line up before I feel confident on starting a video journey that we might not get to finish.

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 54 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined