Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

sealing drink coasters (paper type)

Featured Replies

Hello.

I'm building a bar in my home game room.  I want to cover the top with coasters I've collected from bars all over the world.  Most are paper based of course.  Questions I have are:

Pour over epoxy or spar coating?  Any brands or type to stay away from?  Food friendly would be desireable.

Will either coating melt or eat the coasters?

All advice is really appreciated.

I had a buddy use pour epoxy on bar top, had golf score cards, pictures, etc., worked fine no issue. He did glue or tape from behind (can't remember what he used) to keep them from moving around during the pour.

 

-Ace-

Epoxy should work. I would do some practice on duplicates to see if the printing might run. There are a lot of folks on the Forum who have lot of experience w epoxy. West Systems is quite popular. There are also casting resins, I guess it depends on how thick you want to imbed any other things. Doing a large surface all at once will require slow setting formulas. Waving a torch or heat gun over the surface will encourage bubbles to rise and pop. 

  • Popular Post

The most important is to seal the coasters first. Resin can soak into it and change totally the look or the dimensions of the coasters. Usually, you want to use a special epoxy made for inclusion. Then a topcoat with a UV resistant epoxy. The inclusion is a multiple step process. First you soak your support with a thin layer of resin. When it starts to gel, you lay your sealed coasters on. When the passed layer is cured, you can add a new layer. And so on until the coasters are fully covered. The thickness of each layer depends of the manufacturer's recommendations. Big pours may warm up too much. Then you can add your UV resistant layer which will protect both the resin and the coasters.

For a good pour, you don't want to pour all over the piece. Just pour in the middle, as higher as possible for a thin running of resin and avoid bubbles, and let the resin flow all around. You need a clean, warm and dry environment and a dimensioned plastic cover to prevent any dust to come during the curing process. Your worst enemies will be time, we'll talk about that later, and mostly bubbles and dust. As wdwerker said you can pop the bubbles out with a heat source. Gas is clean. Prefer the torch because heat guns can blow some air dust into the piece. Don't overheat the resin and be always running, just pass quickly above the surface until you can't see any bubble popping.

To succeed with resins you need to be clean, precise and organized, but more important, you need to manage time. Take the required time for a good mix, then pour as quick as possible. You have a limited amount of time before the gel state, which is the deadline. When the resins starts to gel, you need to raise your hands up, there's nothing much you can do except mistakes. That limited amount of time between the mix and the gel is all you've got to pour, to allow the resin to flow, and to pop out the bubbles. Sometimes, you can push a bit the resin in a far corner with the torch if you see the gel state coming soon. Remember resin curing time is dependent of ambient temperature and moisture. If a resin don't want to cure, its because of temperature or because of a wrong mix : proportions or insufficient mixing. If this issue appears, try to raise the temperature of the room. If it's not enough, remove the resin, cleanup and retry.

If you're an absolute beginner with resin, it's wise to test yourself with a smaller project prior to do large jobs.

  • Author

Thanks to all of you for your answers. I can see that I will probably do a little practicing if I use the resin.  

Also ensure I'm mixing the ingredients well before use.

 

 

I believe polyester resin is cheaper than most epoxies, and doesn't seem to discolor as bad. 

But no Shellac! :)

The problem with Polyester resin is that it's not self planning like epoxy. You need to work upside down in a mold and/or cover your last layer with a plastic sheet  or a waxed glass to force the resin to be flat. On the other hand, polyester is cheaper and can stand UV as it is (no discolor or yellowing as said Marmotjr), it is also very toxic with an awful smell. Well ventilated area and respirator strongly recommended, with gloves and apron which are the minimum with resins. If you go with polyester, don't buy the cheap one, buy a superior inclusion polyester resin in a art shop.

For a product recommendation, I used a product called Ultra Clear Epoxy with a friend who was doing his bar top with music related items embedded under the epoxy. More information is at their site: http://www.bestbartopepoxy.com/ I never used anything else but this worked well, was easy to use and looks crystal clear today, 3 years later. Jean describes the process we used. The first layer was laid down, left to gel and then we embedded the items. When that cured we poured the remaining layers.

 

 

Sent from my iPhone using Tapatalk

On 8/14/2017 at 8:27 AM, wdwerker said:

Epoxy should work. I would do some practice on duplicates to see if the printing might run. There are a lot of folks on the Forum who have lot of experience w epoxy. West Systems is quite popular. There are also casting resins, I guess it depends on how thick you want to imbed any other things. Doing a large surface all at once will require slow setting formulas. Waving a torch or heat gun over the surface will encourage bubbles to rise and pop. 

From a local friends recent experience - with many kinds of epoxy and epoxy sealer, I very much agree with the "practice" part.  So far he has had best luck with "bar top epoxy"  (System Three, in his case) - the only one that has not produced a lot of bubbles.

@Dan HWhat is the difference between garnet shellac and another type; like Zinsser Bullseye dewaxed and premixed? I've used Bullseye and it's Ok; certainly dries fast and produces a nice rich finish. I have thinned from the mix from the 2 lb. mix in the can to a 1 lb. not sure you would necessarily want or need to put water based poly over it but it certainly should work. I'm with Eric and I still like the end result with oil based poly, especially the wipe on. 

2 hours ago, Randy said:

@Dan HWhat is the difference between garnet shellac and another type; like Zinsser Bullseye dewaxed and premixed? I've used Bullseye and it's Ok; certainly dries fast and produces a nice rich finish. I have thinned from the mix from the 2 lb. mix in the can to a 1 lb. not sure you would necessarily want or need to put water based poly over it but it certainly should work. I'm with Eric and I still like the end result with oil based poly, especially the wipe on. 

While the outer seal coat will probably protect it, shellac is alcohol based, and a spilled drink might have a chance of penetrating the coaster and destroying it.  Even if it doesn't mess up the coaster itself, it might leave the shellac layer a little funky.   And as far as I've seen, even clear shellac will leave it with a slight amber hue. 

Still interested in the difference between garnet shellac and Bullseye dewed shellac? Color alone? Or is it an actual different type of shellac? I can't tell from descriptions online.

 

Bullseye dewaxed is a 'blonde' shellac, very light colored. Zinnser also sells 'Seal Coat', which is just a thinner cut, and 'Orange' shellac, which has more color, but is not dewaxed. These canned products contain some sort of preservative to extend shelf life. Beware of the production date, if you can figure out how to decode the numbers on the can.

 

 

The safer bet is to buy flakes, and mix only what you need. Flakes are available in a wide range of tones, from 'super blonde' to 'black'. You can 'dewax' your mix by allowing it to settle for a day or two, then decanting the non-cloudy part to another container.

 

I hear a cheap coffee grinder is good for pulverizing the flakes so that they dissolve faster.

 

 

If you buy blond flakes, make sure it's really a dewaxed type. I found it was faster to use a magnetic stirrer than to pulverizes flakes. I can have the shellac totally dissolved within an hour. I DIY my magnetic stirrer :

BOM :

  • 1x 12v 60mm reclaimed fan
  • 1x rocker switch (optional)
  • 1x 5mm led with a 180 ohm resistor (optional)
  • 1x USB outlet
  • 2x 6x8mm cylindrical magnets
  • 1x magnetic stir bar, or a tall (or a stack of) cylindrical magnet

 

Since I didn't see an answer to my specific question about garnet shellac I'll assume it's a color of shellac. I've never had a problem with the Zinsser product and, from what I read online at FWW and from other at least one other professional furniture maker, bad pre-mixed isn't a problem. I don't use shellac much. Poly is a better solution for me. Just was curious about what garnet shellac is.

$40-200 depending on size, RPM, and heat delivered to the plate. School auctions would be a good place to look to pay less. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.