collinb Posted August 15, 2017 Report Posted August 15, 2017 I'm thinking that I'd like to add a T track to the top of my router table. There are times I need a feather board and right now I just can't accommodate one. (I know it's not a good picture of the top but it shows enough.) The laminate top -- I need to ask. Would it work to just directly route the track channel into it? Do these laminates have any tendency to chip? My first instinct is to do it in two steps. #1 route a small channel the #2 route the full-width channel. All the while with a sacrificial piece on top to mitigate chipping. But are there other, better approaches to take? Quote
wdwerker Posted August 15, 2017 Report Posted August 15, 2017 The 2 or 3 pass groove rout is a good idea. Do you have a downcut spiral bit? If not there isn't a big chance for chipping. Slow steady feed rate should do the trick. Quote
Brendon_t Posted August 15, 2017 Report Posted August 15, 2017 I'm not sure if it helped, but before I routed a channel for a mitre track in my old melamine top, I also scored the top with a razor knife and the lines came out very sharp. No chipping at all. 2 Quote
Jean [Fr] Posted August 15, 2017 Report Posted August 15, 2017 I do just like @Brendon_t , I cut the laminate with an old chisel prior to any machining. I tried specialty bits or blades with no success. There's nothing else you can do to prevent a laminate to chip out when it decided to. Once machined, I seal the groves with some glue. Quote
Tom King Posted August 15, 2017 Report Posted August 15, 2017 I'd turn the whole thing upside down on the tablesaw, and cut it with a Mr. Sawdust blade for the outer edges. It has very sharp, pointed teeth, and cuts laminate cleanly, but I doubt many people have this blade any more. A crosscut blade without flat tops should do it too. Quote
RichardA Posted August 15, 2017 Report Posted August 15, 2017 48 minutes ago, Brendon_t said: I'm not sure if it helped, but before I routed a channel for a mitre track in my old melamine top, I also scored the top with a razor knife and the lines came out very sharp. No chipping at all. I would also add blue tape after scoring. Quote
Pondhockey Posted August 15, 2017 Report Posted August 15, 2017 37 minutes ago, RichardA said: I would also add blue tape after scoring. After scoring? I'm following this thread with some interest, and I'm wondering if the blue tape idea could backfire. Where would you position the edge of the tape? [Edit: Collin, do you have some material to practice on?] Quote
Brendon_t Posted August 15, 2017 Report Posted August 15, 2017 I'm also off the mindset that you can try to reduce but if it does chip out a bit, it shouldn't ruin anything. Quote
collinb Posted August 15, 2017 Author Report Posted August 15, 2017 56 minutes ago, Pondhockey said: After scoring? I'm following this thread with some interest, and I'm wondering if the blue tape idea could backfire. Where would you position the edge of the tape? [Edit: Collin, do you have some material to practice on?] No, but sink cutouts are cheap to pick up. Quote
Jsmims Posted August 17, 2017 Report Posted August 17, 2017 I routed mine in one pass without any chip out, just went very slow and let the bit cut since burning really didn't matter to me.. but looking back I should have took two passes nice and slow Quote
Jean [Fr] Posted August 17, 2017 Report Posted August 17, 2017 Lucky you ! Chip out have more to do with laminate quality, and the strength of the underneath, thing you really can't know. Precautions must be taken anyways. Quote
gee-dub Posted August 17, 2017 Report Posted August 17, 2017 You could certainly run a 1/4" groove about 3/16" deep along the center of the path to see how your laminate reacts to make yourself more comfortable. This would disappear into the final size. Not knowing any better I just did mine in multiple passes like I would if the laminate wasn't there and it worked fine. As mentioned, the quality of the laminate and the application will vary your results. 1 Quote
Popular Post wdwerker Posted August 17, 2017 Popular Post Report Posted August 17, 2017 Downcut spiral bit virtually removes the risk of chipping the laminate. This kind of bit does leave the groove packed with the shavings/sawdust but the edges are clean. https://www.amazon.com/Whiteside-Router-Bits-RD2100-Standard/dp/B000K29T64 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.