Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

New Delta vs used Jet table saw: opinions needed

Featured Replies

Hello,

I am looking to upgrade my current Delta contractors table saw and need some advice. I was looking at getting either the Ridgid R4512 or Delta 36-725 table saw and decided on the Delta mainly due to the better fence. 

I had come across a used Jet JWTS-10JF in my area that was rather over priced. After making an offer several weeks ago they came back with a more reasonable price, a bit high I think, but reasonable.

Anyone here have any experience with either of the two?

 

Any input is more than welcome!

 

Thank you!

There have been a number of members here that use or have used the Ridgid R4512 and I can't recall hearing any real negatives.  It seems to be a solid saw in its price range.  Based on that information and the fact that the Jet is used, I would probably go with the Ridgid.  The plus in my mind is you will have a warranty with the new Ridgid, not the jet

Delta has had such a horrid history over the last 10 years or so of frequently changing ownership, terrible customer service, and parts unavailability. For those reasons, I've pretty much permanently crossed them off my list.

The Ridged has some alignment issues earlier on, but that's fixed & for the price point it seems like a good saw.

I had that model of Jet (except with a Biesmeyer fence) for about 15 years & was very pleased with it. After the initial setup & calibration, I didn't have to do a thing with it, other than the occasional cleaning & greasing. The only downside to it is there is no riving knife & the stock guard is really crappy. I don't know what there is for an aftermarket guard & riving knife. If that's available, I wouldn't hesitate to buy that saw. I sold the Jet, with a 52" Bies fence, crosscut sled & a couple of good blades for $300 Cdn.

The only person I can think of with that Delta is Cliff, and his saw seems to have a pretty critical error.  His miter slots don't run parallel if I remember correctly.  0/1 in my book.

I can't think of anyone that has talked about owning a Jet table saw.  I think Jet makes some decent tools, but if "no one" buys their table saws, there's probably a reason.

Lots have Ridgids, including the current 4512 Chet mentioned.  Some have reported the same alignment problems that plague random Grizzly table saws, but most are happy with the saw.  It seems to be the clear winner in the sub $850 contractor/hybrid saw category.

I’ve had that Jet for 5 years now and have no problem at all. It came with a riving knife for a full kerf blade and I prefer a thin kerf, so off it went and I just try and watch my rips. I know, knot a good idea. My first saw was an old Craftsman so actually don’t have anything to compare it to, but I have no complaints what so ever. What are they asking for the Jet? 

25 minutes ago, K Cooper said:

I’ve had that Jet for 5 years now and have no problem at all. It came with a riving knife for a full kerf blade and I prefer a thin kerf, so off it went and I just try and watch my rips. I know, knot a good idea. My first saw was an old Craftsman so actually don’t have anything to compare it to, but I have no complaints what so ever. What are they asking for the Jet? 

Coop, did yours come with a riving knife or a splitter. The Jet I had looks identical, but had the old green paint & it had a splitter that the guard attached to. It was a friggin awful setup & I just removed it. Otherwise, it sure was a good saw.

Gosh, not sure now that I know the difference. I think it was a riving knife. It fit behind and partially over the top of the blade and would raise and lower with the blade, if I remember correctly. The blade guard was attached to it. Mine is white. 

I’ve got the 4512 and have been quite happy with it. Have to pay extra attention to fence at both ends as the outfeed side does occasionally want to deflect one direction or the other, but it can be overcome with a bit of patience and diligence.  Hoping to have mine for many years to come, until I can get out of my garage and into a stable shop.

You didn't say anything about your current saw except that it's a contractor saw.  Some people say contractor saw when what they mean is jobsite saw.  A contractor saw has a cast iron top and the (induction) motor hangs out the back of the saw, like the used Jet you are looking at.  A jobsite saw is more portable and has a universal motor inside.  If what you have is really a contractor saw, then neither of those saws is going to be much of an upgrade and you should be looking at cabinet saws if you want to upgrade.  If what you have is a jobsite saw, then any of them is going to be a big upgrade.  I would tend to favor the hybrid saws (Ridgid or Delta) just because of the better dust collection.

  • Author

What I have now is a Shopmaster TS350. Its direct drive like a jobsite, but has the CI top and wings as well as stationary base. So cheep small contractor. 

The Jet was up for 650, they came down to 450 so far. I can see a splitter or knife in the pic but cant tell which it is but no blade guard. It has stamped wings like the Delta and Ridgid, and is the older green color rather than the current white they use.

I was sold on the Ridgid until I knew about the trunion and alignment issues. That and the bies style fence lead me to the Delta. I understand that parts availability issues is due to the ownership changing hands. It looks like there is decent suppprt for current products. I can't get anything for the 350.

Now you guys have me back to the Ridgid. 

 

Ya, even $450 is too much for that Jet. That's about what it was brand new.

The "bies style" fence on that Delta is a very light duty version & they are not very robust at all. Lots of flex on the far end.

I've got the ridgid, and I've been pretty happy with it for this type of saw. The fence is fine, although I won't claim it's perfect. It works better if you push it forward a little as it locks down, so it will stay square. The alignment issues seem to come down to 3 things:

1. The original trunnions on the saw were not beefy enough. There's a version 2 that's on the saws after 2013.

2. Some of the saws would have the motor bracket get bent in shipping, since the saw ships upside down with all the weight of the motor on it in the wrong direction. That was fixed by shipping all the saws with a styrofoam block under the motor.

3. At the end of the day, it's a decent saw but it's not a cabinet saw. If you put excessive force on the blade or mechanisms, they will deflect a bit.

I would buy it again, although that's partly influenced by budget, and partly because I needed it's mobility in my garage. I've put on a router table extension, and a light folding outfeed table.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.