freedhardwoods Posted May 17, 2020 Report Posted May 17, 2020 My son (Jim) and I have 2 random orbital sanders; a $100 Makita, and a $35 Black & Decker. After much use on both of them, they spin up to full rpm at no load instead of slow rpm when they were new. That high rpm makes it very likely to make a divot in the wood/plywood when you lift the sander to move to another spot. Can that be fixed? Is it worth fixing or just get new sanders? Jim wants to just get a couple of the B&D's and forget the old ones. Quote
wtnhighlander Posted May 17, 2020 Report Posted May 17, 2020 I doubt it will be less costly to fix than to replace a $35 tool. Going that route, I would grab a cupon and head to Harbor Freight. Their ROS is at least as good as the B&D, and you might shave another $10 off the price. I used one for about 3 years, until one too many drops to the concrete broke the pad off. Still worked fine to that point. 1 Quote
JohnG Posted May 17, 2020 Report Posted May 17, 2020 I’ve never heard of an ROS that doesn’t run full speed under no load. Are you sure they did that? Quote
freedhardwoods Posted May 18, 2020 Author Report Posted May 18, 2020 I was pretty sure you wouldn't fix one for less than $35 but thought I would see if anyone had one repaired before. The motor always did stay at full speed, but the pad didn't spin very fast at all when new. Quote
drzaius Posted May 18, 2020 Report Posted May 18, 2020 I have an old Dewalt ROS that has a friction ring behind the platen. It is a consumable & when it gets worn, the platen spins freely. My Bosch does not have one & will eventually spin up to high speed if it's not held to the work surface. 1 Quote
freedhardwoods Posted May 18, 2020 Author Report Posted May 18, 2020 3 minutes ago, drzaius said: I have an old Dewalt ROS that has a friction ring behind the platen. It is a consumable & when it gets worn, the platen spins freely. My Bosch does not have one & will eventually spin up to high speed if it's not held to the work surface. I'll check that out. Maybe I can fix it. Quote
Coop Posted May 18, 2020 Report Posted May 18, 2020 On a side note, how are you and your son holding up bud? Quote
freedhardwoods Posted May 18, 2020 Author Report Posted May 18, 2020 8 hours ago, Coop said: On a side note, how are you and your son holding up bud? We're doing ok. He is dealing with it by working harder, which is a good thing for our business, because I haven't been doing much in the shop yet. I have been looking at tools and reviews and things like that. Maybe I will get back to work soon, because I slept through the night last night, (I've rarely done that for years), And this morning I want to go to the shop and look inside the B&D sander for the wear ring drzaius mentioned. It's a very obvious $3 part in the Makita parts list. Not sure on the B&D. Headed up there now before breakfast. @drzaius Thanks!! 12 hours ago, wtnhighlander said: I doubt it will be less costly to fix than to replace a $35 tool. Going that route, I would grab a coupon and head to Harbor Freight. Their ROS is at least as good as the B&D, and you might shave another $10 off the price. I used one for about 3 years, until one too many drops to the concrete broke the pad off. Still worked fine to that point Jim likes shopping at Harbor Freight. He might try that. 2 Quote
Chestnut Posted May 18, 2020 Report Posted May 18, 2020 This is a good question something i never knew existed. Thanks. I don't run sanders a ton and i haven't been doing woodworking as long as you probably have. Quote
gmercer_48083 Posted May 18, 2020 Report Posted May 18, 2020 I have been happy with the harbor freight random orbit sander. I have had it now about 4 years and the only thing I don't like is my fingers have difficulty working the on off switch... but may be they are too big. My first B&D wore out the Velcro before its time, and it was cheaper to get the HF as a replacement. Never looked back. Quote
Popular Post freedhardwoods Posted May 19, 2020 Author Popular Post Report Posted May 19, 2020 I removed the pads on both sanders and found the friction ring that @drzaius mentioned. I was able to use some redneck engineering and get both of them working right again. On the B&D, I put a piece of thick black tape under the ring to force it up and put pressure on the pad again. The Makita is made different. I cut a ring out of a milk jug and glued it to the pad. That was enough to put pressure on the friction ring again. I forgot to get a pic of the ring after I drilled the dust holes through my milk jug ring. I really like the Makita sander, but pad is slightly damaged, so I ordered a new pad ($29) and friction ring ($3) to replace at a later time. The friction ring for the B&D isn't available any more but I think my repair will last a good while. 5 Quote
RichardA Posted May 19, 2020 Report Posted May 19, 2020 Love it, this is the kind of engineering that I can't use the politically incorrect term for. Bravo. 1 Quote
wtnhighlander Posted May 19, 2020 Report Posted May 19, 2020 Nice save! Some else is wrong with the sanders, though. Waaaaayyy too clean! 1 Quote
freedhardwoods Posted May 19, 2020 Author Report Posted May 19, 2020 9 hours ago, wtnhighlander said: Nice save! Some else is wrong with the sanders, though. Waaaaayyy too clean! They weren't when I opened them up. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.