Popular Post Von Posted April 22 Author Popular Post Report Posted April 22 Not much shop time lately, but I had a few minutes today and I had to mix up some epoxy for some other stuff so I decided to stabilize/fill some of the knots in my rails. 5 Quote
Popular Post Von Posted April 23 Author Popular Post Report Posted April 23 On 4/22/2026 at 4:42 PM, Von said: Not much shop time lately, but I had a few minutes today and I had to mix up some epoxy for some other stuff so I decided to stabilize/fill some of the knots in my rails. Lesson for other epoxy newbies that follow me: epoxy gets everywhere. It flows between knotholes in your wood you had no idea were connected. Even though it may seem way too thick to flow that far, it will do so. Air gap the wood you are filling from any surface it might get stuck to. Cover any pieces of material you are using as dams completely with packing tape, it will find any uncovered surface and glue it to your wood or clamps or anything else. No real harm done but I've got some scraping and sanding in my future. 5 Quote
Ron Swanson Jr. Posted April 23 Report Posted April 23 On 4/23/2026 at 9:27 AM, Von said: Lesson for other epoxy newbies that follow me: epoxy gets everywhere. It flows between knotholes in your wood you had no idea were connected. Even though it may seem way too thick to flow that far, it will do so. Air gap the wood you are filling from any surface it might get stuck to. Cover any pieces of material you are using as dams completely with packing tape, it will find any uncovered surface and glue it to your wood or clamps or anything else. No real harm done but I've got some scraping and sanding in my future. Yikes. Sounds like you got more than you bargained for. Thanks for the tip! Hope it cleans up without too much work. 1 Quote
Popular Post Von Posted April 27 Author Popular Post Report Posted April 27 Started on the mortises in the legs yesterday. I drilled all my drawbore holes (I did them first based on a tip from TWW in a recent video, not sure it really matters much, but it was a good warm-up) and then roughed out my first mortise with a forstner bit. Started with my drill guide and figured out it can't go to the depth I want with my shorter bits, so I finished on the drill press. Plan to do this all around and then circle back and clean up the sides with a router or chisel. 5 Quote
Ron Swanson Jr. Posted April 27 Report Posted April 27 Looks like you are off to a great start! 1 Quote
Popular Post Von Posted May 3 Author Popular Post Report Posted May 3 I admit, I have to double and triple check myself when it comes to rails with tenons. What I care about is the span on between the outside of the legs, which means I care about the thickness of the legs and the distance between the shoulders of the rails. But when it comes to cutting the rails, I have to add in the two tenons. It's not rocket science, but enough numbers that I know from experience I can easily get confused and I make myself go slow. I'm sure I've cut rails with only enough length for one tenon in my past. As an update, I finished my epoxy filling of various knots and checks. Not sure it was worth it, but it's done. And my shop time was so chopped up the last couple of weeks I don't know I could have gotten anything else done. The sanding flat of the epoxy did results in my taking off some of my mortise layout marks, so I had to go back and redo some of that that. I certainly mis-ordered those operations. Anyway, back onto joinery. 4 Quote
Popular Post gee-dub Posted May 3 Popular Post Report Posted May 3 On 5/3/2026 at 5:54 AM, Von said: I'm sure I've cut rails with only enough length for one tenon in my past. No! That's never happened to any of the rest of us 6 Quote
Popular Post Von Posted May 4 Author Popular Post Report Posted May 4 Got the mortises roughed out today with a forstner bit. Since I didn't see a good way to index the legs on my drill press table (the legs are much longer than my table is wide), I used the drill guide with various combination squares and ruler stops to set the edges of the mortises and then finished the hogging out on the drill press. I was glad I left the legs long so I had full support for guide on the upper mortise. Next step is cleaning up the sides. 6 Quote
Popular Post Von Posted May 7 Author Popular Post Report Posted May 7 Got an hour in the shop this morning and finished cleaning up the mortises. One of the toughest questions in woodworking is "Am I close enough?" I'm certainly not as dead on as I would like with regards to the vertical start and stops of all my mortises. I probably have about 1/16" of variance. Rather than try to chase this, my plan is to leave a little vertical play in the tenons and fine-tune the rail location before I drive the draw bores. I think the main reason for my slop is mostly to do with that I'm using the bottom of the legs as my reference point and I'm not used to making accurate measurements at the scale of a yard. That's too long for any of my combination squares and I don't have ruler stops that fit by yard sticks. I'm using stair gauges as stops, which is OK, but the stair gauges are small and I wish I had more surface area making contact, it's easy to pivot on the gauges a bit. So some bigger ruler stops are now on the shopping list. I can think of ways to remove the vertical slop, e.g. ganging the legs, but they seem to leave more room for horizontal slop, which seems more critical to remove. I do think I have all my mortise widths identical (though experiences tells me not to count on this). 6 Quote
Popular Post Von Posted May 9 Author Popular Post Report Posted May 9 Successful dry fit of first subassembly. I cut my tenons conservatively and am sanding them to fit. Took it apart to ease edges, do draw bores, chamfer the feet, drill the holes in the upper rail to for bolts to hold the top down, and sand. 4 Quote
Ron Swanson Jr. Posted May 9 Report Posted May 9 On 5/9/2026 at 5:46 PM, Von said: Successful dry fit of first subassembly. I cut my tenons conservatively and am sanding them to fit. Took it apart to ease edges, do draw bores, chamfer the feet, drill the holes in the upper rail to for bolts to hold the top down, and sand. Looking good @Von!! 1 Quote
Popular Post Von Posted May 12 Author Popular Post Report Posted May 12 A little more shop time and got the second subassembly dry fit. One lesson (re-)learned: if your wood is a little wet, tenons will dry and shrink. The ones of the first subassembly, which I fit right after milling, are definitely a little looser after a couple of days. Still snug enough I'm not going to worry about it but noticeable. It was easier fitting the second subassembly. I'm glad I went conservative on my tenon milling. Another lesson, I picked up a mostly complete set of transfer punches cheap and they are great for marking the draw bore holes, but use the punch 1/64" smaller than the hole. The same-sized punch binds and is a royal pain to get out. Easing edges. I picked up an second little DeWalt trim router used and cheap and plan to leave it set up for chamfering. I ended up with these carpet squares and am liking them for sanding and routing. I plan to pre-finish before glue up and am looking to use up stuff around the shop. These two bottles of Tung oil are looking like good candidates for the bottom of the bench. 4 Quote
Ron Swanson Jr. Posted May 12 Report Posted May 12 Looking good Von. Fwiw, between the glue bond and the draw boring, i don't think a slightly loose fit is anything to worry about at all. And the glue will cause it to swell so you'll likely get a tiny bit of that back in the end. Are the 4 offset holes dog holes? Holdfast storage perhaps? Quote
Mark J Posted May 13 Report Posted May 13 16 hours ago, Von said: use the punch 1/64" smaller than the hole. The same-sized punch binds and is a royal pain to get out. The draw bore holes in the tenon are a tad bit closer to the tenon shoulder than the bore hole in the leg. If the punch diameter is a tad bit smaller than the bore hole in the leg, and the punch were positioned toward the shoulder the punch mark might be shifted to the shoulder just the right amount. Not sure this would work, just thinking out loud. 2 Quote
Von Posted May 13 Author Report Posted May 13 On 5/13/2026 at 8:33 AM, Mark J said: The draw bore holes in the tenon are a tad bit closer to the tenon shoulder than the bore hole in the leg. If the punch diameter is a tad bit smaller than the bore hole in the leg, and the punch were positioned toward the shoulder the punch mark might be shifted to the shoulder just the right amount. Not sure this would work, just thinking out loud. Interesting idea! Thinking through it out loud, if I want a 1/16" offset, I'd use a punch 1/8" smaller in diameter (so the punch radius == desired offset) and pull it tight to the shoulder side of the hole when marking. Solves the punch sticking problem and also takes out the step of shifting the mark using dividers. Seems less fussy overall. Thanks - I'm going to give this a try and will report back. 1 Quote
Popular Post Von Posted May 14 Author Popular Post Report Posted May 14 Cut my legs to length, including stub tenons in the tops. I used the track saw to cut the shoulders and then finished the tenons with a chisel and rip saw. Having learned to give my tenons a couple days to acclimate, I cut my long rails. Finally, I realized I put a chamfer on a rail corner I shouldn't have, so glued some replacement wood in place. 4 Quote
Mark J Posted May 14 Report Posted May 14 23 hours ago, Von said: I'm going to give this a try and will report back You definitely want to test out this idea, before committing to it fully. 2 Quote
Popular Post Von Posted May 15 Author Popular Post Report Posted May 15 Finished up my drawbore holes on the short rails. These were already marked before I got @Mark J's idea. I tried remarking them, but the punch just deflected into the existing marks, so these marks are unshifted. Capturing my process. I clamp the rail down such that the drill bit hits the mark. I nudge the fence up against the edge of the rail and a stop against the end, but with 3/32" of shims between the end of the tenon and the stop. Then I unclamp the rail, remove the shims, and push the rail against the stop, shifting it 3/32". I re-clamp the rail and drill. I think a brad point bit here is key to avoid drifting. Later, rinse, repeat... I'm giving the tenons in the long rails another day or two to acclimate before I fit them and I'll try Mark's technique for marking them. Not sure if I'll be able to support the long rails on my drill press, so I'll have to cross that bridge. Had a little time, so I started making some draw bore pegs. The new mallet, with its extra heft and hardness, makes this process easier if louder. I'm going to need 24 pegs, plus a few extra for contingencies. Out of caution, I'm going to let them acclimate after riving them to 7/16" before going down to 3/8". 5 Quote
fcschoenthal Posted May 15 Report Posted May 15 I like the idea of using the shims to get the same distance each time. The one time that I did drawbores, I just made a mark and went for it. Yours is definitely more accurate and a lot more likely to get even pressure on the joint. 1 Quote
fcschoenthal Posted May 15 Report Posted May 15 Hey Von, Marc just published a video about different finishes for a workbench. Have you chosen what you're going to do with yours? 2 Quote
Von Posted May 16 Author Report Posted May 16 On 5/15/2026 at 11:38 AM, fcschoenthal said: Hey Von, Marc just published a video about different finishes for a workbench. Have you chosen what you're going to do with yours? I saw that video has been released but I haven't had a chance to watch it yet. My current plan is do to Tung Oil on the base and BLO on the top. I'm thinking oil finish because I'm not interested in a film, I want something cheap, I want resistance to glue and other stuff I will spill on it, and, in the case of the Tung Oil, I'm looking to use up stuff I have sitting around the shop. We'll see if Marc's video causes me to change my mind. I believe my thinking is coherent with what I've heard him suggest in the past. 2 Quote
Ron Swanson Jr. Posted May 16 Report Posted May 16 On 5/16/2026 at 6:12 AM, Von said: I saw that video has been released but I haven't had a chance to watch it yet. My current plan is do to Tung Oil on the base and BLO on the top. I'm thinking oil finish because I'm not interested in a film, I want something cheap, I want resistance to glue and other stuff I will spill on it, and, in the case of the Tung Oil, I'm looking to use up stuff I have sitting around the shop. We'll see if Marc's video causes me to change my mind. I believe my thinking is coherent with what I've heard him suggest in the past. Good plan, sir. 2 Quote
Von Posted May 17 Author Report Posted May 17 On 5/16/2026 at 7:12 AM, Von said: I saw that video has been released but I haven't had a chance to watch it yet. My current plan is do to Tung Oil on the base and BLO on the top. I'm thinking oil finish because I'm not interested in a film, I want something cheap, I want resistance to glue and other stuff I will spill on it, and, in the case of the Tung Oil, I'm looking to use up stuff I have sitting around the shop. We'll see if Marc's video causes me to change my mind. I believe my thinking is coherent with what I've heard him suggest in the past. As one would expect, a good video from Marc going through different finishing options (oils, varnishes, oil/wax blends and oil/varnish blends if my memory serves me). Nothing surprising but well laid out. No changes to my plan but good reassurance of course. 1 Quote
Botch Posted May 17 Report Posted May 17 You may be the first person in history to cut tenons with a tracksaw! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.