Popular Post Von Posted July 3 Author Popular Post Report Posted July 3 I wanted something that would hold my bench base square but not be in the way of the top so I could install it on a square base and hopefully have it keep things square. A 4' spreader/clamp was just a little too long and in the way. I ordered this Fastcap Upper Hand, attached a couple custom feet and it is working well by spreading the two legs apart just enough to bring everything into square while staying below where the top will sit. On 6/28/2026 at 12:54 PM, Chet said: If your shop floor is like mine you might want to see how much it rocks when it is in its final spot. When Ibuilt my bench I too had a rocking problem. I decided to move it where it would be used to see how much I had to deal with and to my surprise there was no rocking at all Agreed. I know from moving it around the floor isn't going to solve my problem (I have ~3/8" of gap under a foot) but I will move it into position and square it up before placing the top. Thanks! 5 Quote
Ron Swanson Jr. Posted July 3 Report Posted July 3 Nice job making those pads to accommodate the 3rd hand tool. 2 Quote
Von Posted July 3 Author Report Posted July 3 On 7/3/2026 at 11:50 AM, Ron Swanson Jr. said: Nice job making those pads to accommodate the 3rd hand tool. Thanks. I admit it was a satisfying little project. 1 Quote
Popular Post Von Posted July 13 Author Popular Post Report Posted July 13 Getting ready to start making the top. I'm going to try to make slabs by flattening ~2x11" boards and gluing them face-to-face to make 4x11" pieces. One for each side of the top, with a gap in between for the planing stop. Looking at my boards I think they are flat enough I can do this without losing too much material. Why? I like the idea visually of a slab but didn't want to have to wait for at least another year for 4" thick material to dry. I haven't see this approach done (except by Cremona who uses actual 4"-thick slabs) and am curious if it can be done. I figure I'll try this and shift over to making ~2x4"s if it doesn't seem to be working out. I made some quick'n'dirty winding sticks to help me judge twist in my boards. 3 Quote
Ron Swanson Jr. Posted July 13 Report Posted July 13 On 7/13/2026 at 8:18 AM, Von said: Getting ready to start making the top. I'm going to try to make slabs by flattening ~2x11" boards and gluing them face-to-face to make 4x11" pieces. One for each side of the top, with a gap in between for the planing stop. Looking at my boards I think they are flat enough I can do this without losing too much material. Why? I like the idea visually of a slab but didn't want to have to wait for at least another year for 4" thick material to dry. I haven't see this approach done (except by Cremona who uses actual 4"-thick slabs) and am curious if it can be done. I figure I'll try this and shift over to making ~2x4"s if it doesn't seem to be working out. I made some quick'n'dirty winding sticks to help me judge twist in my boards. So then the face grain will be the bench top? 1 Quote
Von Posted July 13 Author Report Posted July 13 On 7/13/2026 at 11:36 AM, Ron Swanson Jr. said: So then the face grain will be the bench top? Yes. Quote
Ron Swanson Jr. Posted July 13 Report Posted July 13 On 7/13/2026 at 4:22 PM, Von said: Yes. Gotcha. Just making sure I was following correctly 1 Quote
Popular Post wtnhighlander Posted July 14 Popular Post Report Posted July 14 I don't know if it walk make any significant difference, but increasing the number of layers in the lamination will decrease the risk of warpage in a couple ways. Smaller pieces means less acculated force per piece. More pieces means there is more chance for stresses in the parts to oppose and 'cancel out'. Personally, I like having the edge grain up, vs. face grain. My bench is construction lumber, and I don't mind screwing parts to it when needed. The edge grain 'self-heals' from such damage better than face grain. This may not apply to hardwood, though. 3 Quote
Popular Post Von Posted July 14 Author Popular Post Report Posted July 14 On 7/13/2026 at 9:00 PM, wtnhighlander said: I don't know if it walk make any significant difference, but increasing the number of layers in the lamination will decrease the risk of warpage in a couple ways. Smaller pieces means less acculated force per piece. More pieces means there is more chance for stresses in the parts to oppose and 'cancel out'. Agreed. I recognize I'm taking a bit more risk. On 7/13/2026 at 9:00 PM, wtnhighlander said: Personally, I like having the edge grain up, vs. face grain. My bench is construction lumber, and I don't mind screwing parts to it when needed. The edge grain 'self-heals' from such damage better than face grain. This may not apply to hardwood, though. Maybe a question revealing a big gap in my knowledge, but is there really such a thing as edge grain vs face gain in that the wood presents differently somehow? Or is it just how we refer to the wider and narrower parts of a board? Perhaps a way to frame my question: if someone were to hand me a 4"x4", should I be able to identify two sides as face grain and two sides as edge grain? TIA. 3 Quote
fcschoenthal Posted July 14 Report Posted July 14 On 7/14/2026 at 11:45 AM, Von said: Maybe a question revealing a big gap in my knowledge, but is there really such a thing as edge grain vs face gain in that the wood presents differently somehow? Or is it just how we refer to the wider and narrower parts of a board? To me, the face grain is closest to the outside of the tree, or kind of parallel to the growth rings. the edge grain would be more perpendicular to the rings. But I could be just talking out of my rear facing orifice. I don't know if it presents differently, or makes any difference in properties. On 7/14/2026 at 11:45 AM, Von said: Perhaps a way to frame my question: if someone were to hand me a 4"x4", should I be able to identify two sides as face grain and two sides as edge grain? Not any 4x4 that I've seen where the pith is in the center of it. They'd all be face grain. 2 Quote
Popular Post wtnhighlander Posted July 14 Popular Post Report Posted July 14 I guess thechnically, the wider face is called 'face', and the narrower face is called 'edge'. Most commonly, the wider 'face' is more likely to present cathedral grain pattern, which can be more likely to separate or peel away with heavy use. (Keep in mind,my workbench experience is with pine, not hardwood.) The 'edge' is more likely to present straight 'vertical' grain, like a quartersawn board has on the wide 'face'. In a hardwood, especially one without the strong growth ring contrast of yellow pine or red oak, none of this probably matters at all. 3 1 Quote
Popular Post Von Posted July 19 Author Popular Post Report Posted July 19 I started working on the top today by milling one the boards. These boards, at 8'x11"x2" are by far the largest I've milled so I expected some challenges just based on size. My usual approach is to use a scrub plate to get one face (if there is cup, I use the crown side) flat enough and then with that face down, use my thickness planer to mill the other side and then flip it over and finish flattening the first side. I then use the track saw to square up the edges. The main thing I've learned about "flat enough" is the board cannot rock in any way as that will cause the thickness planer to do odd, undesirable things as the board shifts. The challenge with my regular approach is that a scrub plane on a board this big creates a lot of force, enough that my current workbench was moving around on me. So I shifted to the powered hand plane, which has that nice benefit that it planes without putting a lot of force into the board. I got a fair amount of practice with it and got much better at using it, learning to let the weight of the tool do the work and playing with angles of attack to avoid tear out and getting a smoother surface. It's biggest downside in my opinion it that it throws shavings everywhere to its right. I followed up with my scrub plane to knock down remaining high spots as identified with a straight edge. I found the winding sticks I made not very helpful. The combination of my older eyes and the challenge of holding my head steady meant they didn't really tell me anything I couldn't tell by plain eye. I suspect lack of experience on my part. What was useful is I've gotten in the habit of leveling my bench before milling and this lets me use a level to gauge twist and unevenness in the board. This isn't perfect but it lets me find issues I can't see. In the photo below you can see I've got a high side on the right that wasn't apparent to me my eye. I used my scrub plane again to knock down this unevenness, checking with the straight edge as I went to keep things flat. With one side flat enough, it was off to the thickness planer, where all went well. I have 1/2" wide strip of of low spots on one side from the original Wood-mizer milling. I'm going to wait and see if it's going to be an issue. I think I can put it towards the inside of the bench, where I don't think I'll care about it. After one board, my body was done for the day. I was reminded that I am just barely capable of moving boards this big around the ship. With three boards to go, I'm tempted to get a height-adjustable rolling cart of some sort. I finished by cleaning up the shop. Not something I'm usually do every day, but with the amount of shavings created, it seemed necessary. 7 Quote
Popular Post roughsawn Posted July 19 Popular Post Report Posted July 19 Von, g-man has posted the height adjustable cart that he uses...I thing he has two. I bought one last year from Home Depot after his recommendation...for moving my big slabs around, and also for an outfeed table for the planer and bandsaw. Some of the best money I've spent for the shop. Very reasonably priced. Comes in a box, and I think I put mine together in 20 minutes. Very simple assembly. 3 2 Quote
Popular Post Von Posted July 19 Author Popular Post Report Posted July 19 Found a taker for all my oak sawdust and shaving, a professor on campus who, as part of his research, is raising rhinoceros beetles. The larva are raised on fermented oak sawdust/shavings. On 7/19/2026 at 4:13 PM, roughsawn said: Von, g-man has posted the height adjustable cart that he uses...I thing he has two. I bought one last year from Home Depot after his recommendation...for moving my big slabs around, and also for an outfeed table for the planer and bandsaw. Some of the best money I've spent for the shop. Very reasonably priced. Comes in a box, and I think I put mine together in 20 minutes. Very simple assembly. Thank you. Indeed, they have a variety of options but this one looks like a good basic one and they offer free delivery. 3 Quote
gee-dub Posted July 20 Report Posted July 20 Yep, that's the one and I do have two. As to the beetle, I worked for the Universities of California for 14 years and never though of dropping in to the Entomology building and asking someone if they wanted some sawdust. Too late now. I retired and moved away. Great secondary use. It always makes me smile to find value in something I am just going to throw away. 2 Quote
Popular Post Beechwood Chip Posted July 20 Popular Post Report Posted July 20 Often when I try to give away sawdust, people ask if it contains any plywood or other engineered wood, any pressure treated wood, or anything else. Sometimes they want to know the wood species. Since I use my dust collector for all my tools and for sweeping up, there's going to bits of everything I cut, plus whatever I track in on my shoes. I'd love to find a secondary use for it, but people are so picky about contamination. 3 Quote
Von Posted July 20 Author Report Posted July 20 On 7/19/2026 at 8:51 PM, Beechwood Chip said: Often when I try to give away sawdust, people ask if it contains any plywood or other engineered wood, any pressure treated wood, or anything else. Sometimes they want to know the wood species. Since I use my dust collector for all my tools and for sweeping up, there's going to bits of everything I cut, plus whatever I track in on my shoes. I'd love to find a secondary use for it, but people are so picky about contamination. Agreed, most of the time my dust collector just goes in the trash because I don't know what all is in it. Since I knew this was a likely case and since I was generated so much oak dust/shavings, I cleaned out all my containers before starting so I was confident about the contents. Shavings that I can visually inspect usually go in my compost. 1 Quote
gee-dub Posted July 20 Report Posted July 20 On 7/19/2026 at 5:51 PM, Beechwood Chip said: I'd love to find a secondary use for it, but people are so picky about contamination. Understood. I have two scrap barrels. One is for stuff we can toast marshmallows over and one is for ply, mdf, and other composites that just go into the trash. For the cyclone barrel I cannot confirm or deny unless I have just cleaned it out before a large cherry / walnut / whatever project. Generally it is mix with all sorts of what-not. 2 Quote
Popular Post fcschoenthal Posted July 20 Popular Post Report Posted July 20 On 7/19/2026 at 4:49 PM, Von said: they have a variety of options but this one looks like a good basic one and they offer free delivery. I had thought of getting one of those, but am vacillating on getting one of the cheap electric standing desks off of Amazon. They are about ½ the price and can still hold a couple of hundred pounds. The problem for me would be where I would put a 2'x4' object when I wasn't using it. 3 Quote
Von Posted July 20 Author Report Posted July 20 On 7/19/2026 at 11:54 PM, fcschoenthal said: The problem for me would be where I would put a 2'x4' object when I wasn't using it. Yeah, that will be a long-term problem for me as well. I'm pretty sure I could make room for it, but it doesn't seem an efficient use of limited space. I think the question will be: how useful can I make it day-to-day, for what I'm not sure? Worst case, I'll use it for the bench build and then sell it. 1 Quote
Popular Post gee-dub Posted July 20 Popular Post Report Posted July 20 I built a shelf under each of mine. One holds my vacuum press and accessories, the other my compressor, hose reel, nailers / brads, and pinners / pins. Of course you still need a footprint to park the buggers. 3 Quote
Ron Swanson Jr. Posted July 20 Report Posted July 20 On 7/19/2026 at 7:51 PM, Beechwood Chip said: Often when I try to give away sawdust, people ask if it contains any plywood or other engineered wood, any pressure treated wood, or anything else. Sometimes they want to know the wood species. Since I use my dust collector for all my tools and for sweeping up, there's going to bits of everything I cut, plus whatever I track in on my shoes. I'd love to find a secondary use for it, but people are so picky about contamination. For the first time ever I posted two garbage bags full of sawdust and I have no takers after a week. Usually they're gone in 2 hours and I get several inquiries. Pretty soon they will go into my compost pile if I don't get any takers. 2 Quote
Popular Post gee-dub Posted July 20 Popular Post Report Posted July 20 On 7/20/2026 at 12:38 PM, Ron Swanson Jr. said: For the first time ever I posted two garbage bags full of sawdust and I have no takers after a week. Usually they're gone in 2 hours and I get several inquiries. Pretty soon they will go into my compost pile if I don't get any takers. If no one else wants them, Mother Nature will always welcome them back. 3 Quote
Popular Post Chet Posted July 20 Popular Post Report Posted July 20 I have a disabled lady in my neighborhood who takes all my shavings and uses them on the ground between her raised vegetable beds so she can roll her electric wheel chair around without getting mud all over the tires. 5 Quote
wtnhighlander Posted July 21 Report Posted July 21 Maybe I missed it earlier, but is anyone using this type of lift cart? Looks like it can park under a bench when not in use. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.