Mark J Posted January 11 Report Posted January 11 3 hours ago, Von said: magnets are strong enough you don't want to leave them lying around loose on your bench as you work as they will seek out your tools at every opportunity. And don't try to measure them with calipers. 1 Quote
Botch Posted January 12 Report Posted January 12 Not quite sure how I lost track of this thread for so long; @Von, I have a question for you or anyone else who uses offset pinned mortises: When do you check for square between the leg and table, or rail and stile, while you’re pounding in the pins? And, if they are out-of-square, how do you correct for it? I’ve done a few pinned mortises-n-tenons, but I’ve always glued up the assembly with glue and clamps, ensuring they were square, and then drilled for the pins and installed them later. They weren’t offset, drawing the joint together tightly, and not tapered (they may have added a bit of strength, but were probably more for decoration). I would think if I ever tried this kind of joint, I’d drive in the first pin, check for square, and if it was off, use a bar clamp to pull it into square, and then drive in the second pin; but, I could easily see how this second pin could pull the joint out-of-square, the other direction, if the joint chose to be obstinate (as most of mine do). How do you guys correct for this, if necessary? TIA. 2 Quote
Popular Post Tpt life Posted January 12 Popular Post Report Posted January 12 This is a clamp together dry-fit and test, arrangement. Draw boring should only draw tight. This makes your shoulders the critical area for registering for square. I think the only way to fine tune would be to leave some extra material specifically for that. Most of this process I have ever seen, was in the doors of our 1860 Colonial, 20ish years ago. Those slabs could have been too big, banged together, then trimmed for the opening, and no one would ever know. 5 Quote
Popular Post Von Posted January 12 Author Popular Post Report Posted January 12 On 1/11/2026 at 10:52 PM, Botch said: @Von, I have a question for you or anyone else who uses offset pinned mortises: When do you check for square between the leg and table, or rail and stile, while you’re pounding in the pins? And, if they are out-of-square, how do you correct for it? I'm new to drawboring, so caveat emptor, but echoing @Tpt life my plan is to get everything square dry using a combination of clamps and temporary metal draw bore pins (e.g.) and then only when I'm happy with the fit do I add the glue and pins. In practice, I don't see driving the pins crushing the wood enough to pull things out of alignment. It's one thing to pull things tight, it's another to pull them so hard that wood deforms. The pin would give first I expect since it's smaller. That said, if I were to draw bore and find things out of square, I'd expect I'd live with it. I don't expect the bench will stay perfectly square and that's fine. I'm sure my current bench isn't square. Reading Schwarz, he's talks about benches routinely going out of square as wood moves over time. 3 Quote
Popular Post Ron Swanson Jr. Posted January 12 Popular Post Report Posted January 12 On 1/12/2026 at 4:45 AM, Tpt life said: This is a clamp together dry-fit and test, arrangement. Draw boring should only draw tight. +1. Dry fitting before the boring will tell you if you're square or not. The offset is very small, so there shouldn't be any big surprises when the pin goes in. 3 Quote
Von Posted January 14 Author Report Posted January 14 On 1/11/2026 at 11:23 AM, Von said: My biggest challenge was getting the 1" deep hole for the dog head and the ~6" deep hole for the post co-axial. It occurred to me to wonder: How does Andy Klein drill the 6" and 12" holes for dogs in his vise faces? The answer is, he doesn't. I've found he makes his vise faces one of two ways. One way he laminates two boards, in which case he makes matching dados to create a 3/4" square holes for the dogs, then drills out round parts at the top for the dog heads. Or he makes the vise face from a slab and in that case he's hogging out a big recess on the back for his vise and just hogs out a little more for the dogs and then drills the holes for the heads from the top to meet the space he hogged out. Watching him hog out the holes got me thinking (dangerous I know): once the dog is past the first few inches of the hole, I don't think the bottom part of the hole needs to be that snug. All the clamping forces on the dogs will be handled near the top, like with a hold down. When I do this again, I'm going to try drilling holes from the top and the bottom that meet, but oversize the bottom hole so the dog has some play. Quote The magnets are strong enough you don't want to leave them lying around loose on your bench as you work as they will seek out your tools at every opportunity. And don't try to measure them with calipers. To add insult to idiocy, the magnet I tried to measure magnetized my calipers. PITA. Quote
Beechwood Chip Posted January 14 Report Posted January 14 On 1/14/2026 at 3:54 PM, Von said: To add insult to idiocy, the magnet I tried to measure magnetized my calipers. PITA. You can get a demagnetizer. 1 Quote
Popular Post Von Posted March 9 Author Popular Post Report Posted March 9 After about 18 months of drying, with some help from a neighbor, the lumber has hit the shop (ignore the 2x on the pile to the right). It's seemed to have dried well without major issues. I started working on legs. I'm trying to use my worst slabs with pith first. The first blank went fine and is in the clamps. My second set of pieces got a little squirrely on me after I rough cut them. I think one piece can be saved. The other is a cork screw. 8 Quote
Popular Post Chet Posted March 9 Popular Post Report Posted March 9 I am looking forward to watching this finally come together. On 3/9/2026 at 12:05 PM, Von said: My second set of pieces got a little squirrely on me after I rough cut them. I think one piece can be saved. The other is a cork screw. You just never know where you might find some tension in a piece of wood. 3 Quote
Popular Post Coop Posted March 10 Popular Post Report Posted March 10 Dang, has it been 18 months already? Sometimes you work the wood and others, the wood works you. 4 1 Quote
roughsawn Posted March 10 Report Posted March 10 What did the moisture on the surface of the rough lumber get down to? Did you check the moisture after you milled the lumber, and if so, what did it read? 1 Quote
Popular Post Ron Swanson Jr. Posted March 10 Popular Post Report Posted March 10 And down the runway we go! One small and unsolicited suggestion, is you might want to consider milling in phases if you're seeing a lot of movement. Meaning, Mill about halfway, let it sit for a week and then take it down the rest of the way. And maybe you're doing that already. Looking forward to following you on this one! 4 Quote
Popular Post pkinneb Posted March 10 Popular Post Report Posted March 10 On 3/10/2026 at 8:36 AM, Ron Swanson Jr. said: And down the runway we go! One small and unsolicited suggestion, is you might want to consider milling in phases if you're seeing a lot of movement. Meaning, Mill about halfway, let it sit for a week and then take it down the rest of the way. And maybe you're doing that already. Looking forward to following you on this one! x2 I'm sure you are doing this as well but in addition make sure you are taking material from both sides. 3 Quote
Popular Post Von Posted March 10 Author Popular Post Report Posted March 10 (edited) On 3/9/2026 at 11:44 PM, roughsawn said: What did the moisture on the surface of the rough lumber get down to? Did you check the moisture after you milled the lumber, and if so, what did it read? Yes, I've been measuring it regularly. What I figured out is that it varies a lot with the ambient humidity. Last month, when the humidity was 16%, the wood measured 10-12%. On Sunday, when the humidity was 50%, it was 12-14%. For reference, a very dry cherry slab next to it measured 8.9% and 10.6% on those dates. The drying has definitely slowed down the last 4 months. I did a couple spot measurements this morning on new cuts and was still seeing in that 12-14% range. I'll pay more attention next time I make rough cuts, but it seems like the moisture is fairly even throughout. On 3/10/2026 at 9:36 AM, Ron Swanson Jr. said: One small and unsolicited suggestion, is you might want to consider milling in phases if you're seeing a lot of movement. Meaning, Mill about halfway, let it sit for a week and then take it down the rest of the way. And maybe you're doing that already. Thank you! All advice welcome and I admit I jumped in eagerly yesterday and broke that rule so you are wise to remind me. Today I'm sore from moving all that dang wood around, both getting it to the shop and around the shop, so am taking the day off to do other things. On 3/10/2026 at 11:58 AM, pkinneb said: I'm sure you are doing this as well but in addition make sure you are taking material from both sides. Yep. Since I don't have a planer jointer, I'm using a variety of milling techniques depending on the board, but all the milled surfaces get treated at some point in the process, even just getting to a rough blank. Thanks all for the advice. Edited March 11 by Von Jointer not planer 5 Quote
roughsawn Posted March 11 Report Posted March 11 Von, 10% this time of the year (low humidity) scares me. 9% and under, I'm good to go. And when I resaw my 2" slabs, I'll sticker them and leave them sit for 3 or 4 days. Seems they always have 1 to 1-1/2% more moisture in the middle than on the outside. Just gotta be patient. Just think, by this fall, the whole stack will be ready. Good luck with this new project! 2 Quote
Coop Posted March 11 Report Posted March 11 FWIW, get a planer if you have the finances and room. It’s a game changer. 2 Quote
Ron Swanson Jr. Posted March 11 Report Posted March 11 @Von didn't you just recently build a planer sled though? Or am i remembering that wrong? 1 Quote
Von Posted March 11 Author Report Posted March 11 On 3/10/2026 at 9:30 PM, roughsawn said: Von, 10% this time of the year (low humidity) scares me. 9% and under, I'm good to go. And when I resaw my 2" slabs, I'll sticker them and leave them sit for 3 or 4 days. Seems they always have 1 to 1-1/2% more moisture in the middle than on the outside. Just gotta be patient. Just think, by this fall, the whole stack will be ready. Good luck with this new project! Thanks. I'm committed to at least trying at this point. If everything goes sideways, I will enjoy the firewood and learning experience. On 3/10/2026 at 10:37 PM, Coop said: FWIW, get a planer if you have the finances and room. It’s a game changer. Whoops, I misspoke. What I don't have is a jointer. I do have a thickness planer. On 3/11/2026 at 5:50 AM, Ron Swanson Jr. said: @Von didn't you just recently build a planer sled though? Or am i remembering that wrong? Correct. See above correction. It would be odd to build a planer sled without a planer :-) 1 Quote
Ron Swanson Jr. Posted March 11 Report Posted March 11 On 3/11/2026 at 7:37 AM, Von said: It would be odd to build a planer sled without a planer :-) Lol indeed it would! 1 Quote
Popular Post Von Posted March 11 Author Popular Post Report Posted March 11 Here's a little more, very geeky, data on the lumber drying. The dark blue line at the top is the ambient humidity, which I started tracking once it became clear it was effecting things. The light blue line at the bottom is my "control" - a very dry cherry slab next to my oak. Obviously, I'm not using precise tools for measurements (a pin moisture meter and a cheap off-the-shelf humidistat), so take all this with a grain of salt, but the results seem consistent enough I think it captures the big picture. A lot of the moisture has left the wood, but there is definitely some moisture left. But I'm also building a workbench not fine furniture. I don't have any big cross-grain situations and if it warps a little, I have a hand plane. 3 Quote
Ron Swanson Jr. Posted March 11 Report Posted March 11 Looks to my untrained eye like everything is trending normally and as expected. I've always assumed that air dried number would dry like anything else, in that the material closest to the surfaces dries first and the core retains moisture and dries the slowest. Which would explain why you're seeing a slowdown lately. Either way, this has been an educational one for me, and I tip my hat to you for all your efforts here! 2 Quote
Popular Post roughsawn Posted March 11 Popular Post Report Posted March 11 Von, if any of the current project goes sideways, you can always set it off to the side, sticker it, and use it for smaller projects in the future. No sense throwing it on the woodpile. Boxes, push sticks, tool holders...dozens of projects for smaller pieces. I think you'll see smaller movement with larger dimension lumber, and more cupping/twisting with 3/4-1" pieces/slabs. Either way, don't lose any sleep over it. I recently had a 7/8" thick coffee table top glued up and built. Set off to the side due to other projects in the making. When I got back to it, a couple of knots that I had repaired, created quite a cup in the middle. No sense dinking around with it, I ripped the nice grain edges and middle out of it, and threw the rest away. You can always salvage something. 3 Quote
Von Posted March 11 Author Report Posted March 11 On 3/11/2026 at 9:34 AM, roughsawn said: I think you'll see smaller movement with larger dimension lumber, and more cupping/twisting with 3/4-1" pieces/slabs. Either way, don't lose any sleep over it. Appreciate the advice. One thing I should mention is the bench will be made from ~2" thick pieces, so I'm not having to do any resawing, I'm just rough cutting and squaring up. I hope to use to my advantage that my pieces are oversized and I have no true critical dimensions (e.g. I'm shooting for 4"x4" legs but can live with smaller if the wood demands it) . 2 Quote
Popular Post Von Posted March 11 Author Popular Post Report Posted March 11 Got a little more work in today. I measured moisture content on a couple of fresh cuts and saw 13-14%. Not surprisingly, that is a couple percent higher than my surface readings. I spend some time today tuning up my table saw. I was getting a little binding and burning on rip cuts which usually means the back of my blade is drifting in towards the fence. Yep, it was about 40 thousands off, which doesn't seem like much but I find is noticeable. I find if I cat get it to within 5 thousands of parallel that's the point I start chasing my tail trying to get it closer and that's close enough I don't notice any issues. The planer sled is turning out to very useful since I don't have a jointer. Some boards I can plane flat by hand, but some would be a royal pain. Using a technique I'm pretty sure I stole from @gee-dub, I level the sled, and then use the level to guide me tweaking the wedges to get the board flat. One regret is that I made the sled from 3/4" plywood instead of 1/2" - I wish it was lighter. I'm getting in some good upper body workout. First leg blank out of the clamps and second one in. 7 Quote
Popular Post Von Posted March 28 Author Popular Post Report Posted March 28 Slow going, but I finally got the fourth leg blank glued up yesterday. As is my current practice for such laminations, I cut one piece to final width and leave the other oversized so I don't have to try and fail to get them aligned during glue up. Then I'll use the L-fence on my table saw to cut the oversized piece to match the smaller one and do final milling from there. I hope to get to that this morning. 6 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.