Popular Post gee-dub Posted August 27 Popular Post Report Posted August 27 Really moving along Von. I hear you on the dry assembly / disassembly cycles. I just put myself into the mindset that this is going to happen a few times before I'm done. I am always happier with the final outcome when I tweak things and do "one more" dry fit to be sure everything is like I want it. Well worth the extra effort. 4 Quote
Popular Post Von Posted August 28 Author Popular Post Report Posted August 28 Got the tail vise installed today with some fine-tuning to follow. I will say I found this vise very challenging. Besides just being different, it really stretched my brain because it extends past the end of the bench and whenever I was working on it, I constantly had to do 180 flip gymnastics in my head since it was upside down. That was true of the shoulder vise too, but maybe I'm just more used to those. Anyways, some highlights and possible hints for anyone else who does the same... These temporary braces, with 1/8" cut outs to make sure the top of the vise sat proud of the bench top, were invaluable to hold the jaw in place until I could get it bolted on. Tool acquisition disorder win of the day: transfer screws to locate the bolt holes on the jaw. When I attached the jaw, I set the vise open 1/8" with a setup bar to make sure I'd have a little travel left so the jaws would completely close. I'm not sure this was needed, but I didn't want a little shift of the jaws during attachment to mean the jaws wouldn't close completely. And here it is assembled and in action on a test piece of cedar. Top view. You can see I have some rubbing at the back (bottom of the photo). I need to figure out if the jaw or the top is out of square and needs planing. When I have that done, the jaw is protruding a bit. Not sure if it's too thick or if I can close the gap between it and the bench a bit. 6 Quote
pkinneb Posted August 28 Report Posted August 28 Looking good Von!! These benches are a lot of work as this thread shows but when complete are an awesome woodworking tool and bring immense satisfaction every time you walk past . 2 Quote
Popular Post Von Posted August 30 Author Popular Post Report Posted August 30 Got both vises installed and working. I wasted/spent some time with the tail vise trying to adjust the spacing with the bench. I cut some recesses in the back of the jaw trying to close the gap and then ended up too close and having to shim it back out. With 20/20 hind sight it wasn't worth it. Here is it at the end of the day. I maybe got it a little snugger. I put the face vise back on and that unexpectedly took a bunch of time as I managed to disconnect the quick release and then had to spend time sorting that out. The trick is the rod is hex-shaped and you have to get the alignment (in terms of hex face on the rod) between the doohickey on the rod and the handle right for it to work. If you are off by a one hex face, it kinda works, but poorly. And I found this challenging to figure all this out when I am working on the vise upside down since gravity is part of the process that makes the quick release work. Short version: next time, I will index the quick release rod and doohickey before I take it apart. Once I got that sorted out, the vise still wasn't working right - it was very stiff sliding when released and noisey when I turned the screw. I finally figured out there are two set screws at the back that tension a dust shield over the screw. Mine had gotten too tight and were forcing the dust shield into the screw. I loosen them and everything works great now. Short version: Veritas gets a "C" or a "C-" for their manuals. I did a little chamfering around the vise jaws, broke some edges, and put some BLO on the underside. The front part of the top, with the two vises on it, is damn heavy. I managed to break a piece off that I had added to one of my leg tenons, so I had to glue that back on, which slowed me down. Putting on the vise handles, I've decided my first lathe project will be handles made from left over workbench lumber. Now I just need a lathe or, more likely, a friend willing to let me use theirs. 5 Quote
Ron Swanson Jr. Posted August 30 Report Posted August 30 It won't be long now until the unveiling. Nice work, sir. 1 1 Quote
Popular Post Von Posted August 31 Author Popular Post Report Posted August 31 More steps towards the finish line. I realized today I didn't have enough crubber and ordered some more, so that may be a blocker. As you'll see I also ordered another ROS, but I can work around not having one at this point with most of the sanding done. I only sanded most of the bench to 80 and the end grain to 120. Could be I'm lazy, but it gives the bench what I consider the right texture for a workbench. I added a little apron between the tail vise and the leg, so I could have a fixed jaw matching the movable one in size. It will also house a pop-up dog. My 20+ year old ROS gave up the ghost. One bolt hole is stripped out, the holes in the pad are blown out, and various parts between are now ex-parts. Time for a new ROS and I splurged on a green one. My wife asked if it could be my birthday present. I'm a lucky man. Jaws got crubber installed on the appropriate faces and finished. I'm impressed I got the crubber in the right places and only started to apply BLO to one piece of crubber before I caught myself. This is also where I realized I only ordered enough crubber for one sides of the jaws, doh. I put three dogs holes in the back half of the top, which are meant for hold downs. They are placed so a hold down can reach over the planing stop and hold work against it. Coat of BLO applied. I might put a second coat on, but otherwise the back half of the bench is done. 6 Quote
Mark J Posted September 1 Report Posted September 1 In your last picture I noticed you still have a shim under one leg of the bench. Is there still a bit of wobble? Quote
Von Posted September 1 Author Report Posted September 1 3 hours ago, Mark J said: In your last picture I noticed you still have a shim under one leg of the bench. Is there still a bit of wobble? Yes, it got better but there is still a little wobble. At some point I plan to replace the temporary shims with something hot glued to the bottom of the leg. 1 Quote
Popular Post Von Posted September 1 Author Popular Post Report Posted September 1 Not the way I wanted to start my day but no real harm done. I was rotating the top to work on the bottom and was focused on the heavy end with the vise still attached and somehow the other end slipped off the bench. At that point gravity won. A couple dings on the top and a scrape on my hand before I just got myself clear, but no apparent real damage to the vise or otherwise. My new short little apron piece broke off, so that sets me back a day gluing it back on. It occurred to me while I was waiting for the apron glue to dry again, I could do something about some sap wood on the other end of the top that was already showing a little wear. On went some penetrating epoxy to toughen it up. First time I've used this particular epoxy, and wow does it get hot right before it sets up. You are looking at a melting plastic cup. 3 3 Quote
Popular Post Von Posted September 2 Author Popular Post Report Posted September 2 Looks like it's going to take a bit for the crubber I need to finish things off to come in, so I expect it will be slow for the next week as I finish off little things and I'll probably hold further updates until the finish since they are feeling a bit mundane. Today, I flipped the front top over, removed all the vises and gave the bottom and sides a coat of BLO. It was certainly not necessary to remove the vises, but felt good not to have to work around them. I found a couple little dings from the drop yesterday that a little sanding helped smooth out with but nothing noticeable to anyone not looking for them. What you see on the end grain bottom right is penetrating epoxy on sap wood. 5 Quote
Ron Swanson Jr. Posted September 7 Report Posted September 7 Hey @Von I've been meaning to ask you, did you order your crubber from Benchcrafted or elsewhere? I found some a little cheaper a while back, but wasn't sure if it was really the same stuff so I held off. Quote
Von Posted September 7 Author Report Posted September 7 1 minute ago, Ron Swanson Jr. said: Hey @Von I've been meaning to ask you, did you order your crubber from Benchcrafted or elsewhere? I ordered it from Andy Klein since I was ordering bench dogs from him. I've been trying it out in my hold downs and clamps. I'm impressed with the quality but it's not cheap. And now if course I want it to match all around on the bench. Expecting it to arrive tomorrow and I'll have more to say. 1 1 Quote
gee-dub Posted September 8 Report Posted September 8 On 10/30/2025 at 7:16 AM, Von said: Thanks. The big challenge is somehow I have three 5/16" depth stops, each of which uses a different size hex key... McMaster-Carr is your friend. 1 1 Quote
Von Posted September 9 Author Report Posted September 9 20 hours ago, gee-dub said: McMaster-Carr is your friend. Thank you. I also found individual stops at Taylor Tools. BTW, while both my rods where in theory 5/16", I found one was just slightly too big and needed a little sanding to fit 1 Quote
Popular Post Von Posted September 13 Author Popular Post Report Posted September 13 With many thanks to this forum for their advice and support, I'm happy to report I've reached the "it's a workbench" milestone. Still a few odds and ends to do, but it's fully functional at this point. Some "beauty shots" and then some implementation details from the last couple weeks. I just a fresh coat of BLO on so there is a little more sheen than I expect once it cures. The pop-up dogs on the tail vise were challenging. The drill guide was a big help and I would say a requirement for me with marginal straight-drilling capabilities. In the photo below you see me trying a 1/8" pilot hole to help keep things straight and that was a failure, that bit wandered much more than beefier bits and made things worse. I only tried it once. With a little head-scratching, I spaced the pop-up dogs so between them and the jaws, I could clamp anything between 0-22" using the ~7.5" of travel on the vise. In the photo below you see a section of the top that is sap wood. I put some penetrating epoxy on it to solidify it, which it did, but it also made the color match with the heartwood, which was a pleasant surprise. Left to do: Center planing stop, some more dog holes along the front for use with the tail vise and for some sort of lengthwise planing stop, and a proper shim under one foot to replace my temporary wedges. 6 Quote
Ron Swanson Jr. Posted September 13 Report Posted September 13 Looks great man! Awesome job!! 1 Quote
Mark J Posted September 14 Report Posted September 14 Success! Congratulations, you've come a long way from the log you started with. 1 Quote
Popular Post Chet Posted September 15 Popular Post Report Posted September 15 Von, that looks like a bench worth the journey and it should get you years of enjoyment. You might want to go out and hit the top with a hammer just to get the first ding out of the way. On 9/13/2026 at 10:21 AM, Von said: proper shim under one foot to replace my temporary wedges. I have had a temporary shim under one leg on my bench for about nine years now. 2 2 Quote
Ron Swanson Jr. Posted September 15 Report Posted September 15 On 9/15/2026 at 9:44 AM, Chet said: I have had a temporary shim under one leg on my bench for about nine years now. Ha! Same. Not quite as long a time, but yeah. Same. 2 Quote
Popular Post Von Posted September 27 Author Popular Post Report Posted September 27 Finished my planing stop today. A lot of routine work and I'll just touch on a couple of challenges I faced in case they help someone else. My first challenge was that my shoulder vise comes up to the top of my rail, so my stop couldn't go below the rail, at least in that part of the bench, so the usual notch approach wouldn't work (or it could, but would force me to have the stop go towards the shoulder vise and I want it to go the other way so I could use it as a saw stop on the other end). Taking an idea from Nick Pedulla, whose workbench build video is amazing, I made a couple of small ramps with matching cut-outs in the stop. For 1/2" of height, the ramp turned out to be about 25 degrees. The ramps then gets attached to the top of the rails, both facing the same direction. When not in use, the stop sits with the ramps nestled in the notches. It this position, it is flat with the bench top. When I pull the stop towards the foot of the bench, the ramps and notches interact and cause the stop to rise 1/2". I was worried this might take some effort, but turns out it is easily done, even before I've put on finish and added some paste wax. To make it dead simple, I added a finger pull on the underside of the planing stop. One finger in the hole is plenty to raise and lower the stop. My second challenge is that I used some rough cherry for the planing stop and I use my track saw to clean up the edges, but the planing stop was too narrow to fully support the track. The solution I came up with was to build four of these little "jacks." Modeled after machinist jacks, the are just blocks of oak, with a threaded insert and some spare adjustable feet. The feet let me dial in the right height to support my track. Four of them spaced over my 8' track was plenty of support. I ended the day easing the edges and putting on a coat of BLO. I'll post photos later of the finished look. 7 Quote
Ron Swanson Jr. Posted September 27 Report Posted September 27 On 9/27/2026 at 3:06 PM, Von said: Finished my planing stop today. A lot of routine work and I'll just touch on a couple of challenges I faced in case they help someone else. My first challenge was that my shoulder vise comes up to the top of my rail, so my stop couldn't go below the rail, at least in that part of the bench, so the usual notch approach wouldn't work (or it could, but would force me to have the stop go towards the shoulder vise and I want it to go the other way so I could use it as a saw stop on the other end). Taking an idea from Nick Pedulla, whose workbench build video is amazing, I made a couple of small ramps with matching cut-outs in the stop. For 1/2" of height, the ramp turned out to be about 25 degrees. The ramps then gets attached to the top of the rails, both facing the same direction. When not in use, the stop sits with the ramps nestled in the notches. It this position, it is flat with the bench top. When I pull the stop towards the foot of the bench, the ramps and notches interact and cause the stop to rise 1/2". I was worried this might take some effort, but turns out it is easily done, even before I've put on finish and added some paste wax. To make it dead simple, I added a finger pull on the underside of the planing stop. One finger in the hole is plenty to raise and lower the stop. My second challenge is that I used some rough cherry for the planing stop and I use my track saw to clean up the edges, but the planing stop was too narrow to fully support the track. The solution I came up with was to build four of these little "jacks." Modeled after machinist jacks, the are just blocks of oak, with a threaded insert and some spare adjustable feet. The feet let me dial in the right height to support my track. Four of them spaced over my 8' track was plenty of support. I ended the day easing the edges and putting on a coat of BLO. I'll post photos later of the finished look. Very creative solution! Love it!! 2 Quote
Popular Post Von Posted September 28 Author Popular Post Report Posted September 28 A couple photos with the finished planing stop to wrap up this journal. My thanks to everyone who helped and encouraged me along this build. 4 Quote
Mark J Posted September 29 Report Posted September 29 Great workbench! Thanks for taking us along on the journey. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.