Popular Post gee-dub Posted July 21 Popular Post Report Posted July 21 On 7/20/2026 at 5:34 PM, wtnhighlander said: Maybe I missed it earlier, but is anyone using this type of lift cart? Looks like it can park under a bench when not in use. I had one and gave it away to a friend who does work on cars. Despite a couple of rebuilds I could not get it to stop leaking oil on my shop floor so it had to go. It was very useful while I had it. I just got tired of cleaning up after it. 3 Quote
Coop Posted July 21 Report Posted July 21 I bought the one from HD at @gee-dub recommendations and even built the shelf and put my pancake on it. Sometimes the dude has some good ideas! I plan on buying another to primarily be used as an out feed table for my ts. 2 Quote
Mark J Posted July 21 Report Posted July 21 I'll just mention that those hydraulic tables are very heavy. 2 Quote
gee-dub Posted July 21 Report Posted July 21 On 7/21/2026 at 5:32 AM, Mark J said: I'll just mention that those hydraulic tables are very heavy. Yes, good catch. They are stupid-heavy. 2 Quote
Von Posted July 21 Author Report Posted July 21 On 7/20/2026 at 8:34 PM, wtnhighlander said: Maybe I missed it earlier, but is anyone using this type of lift cart? Looks like it can park under a bench when not in use. HF's website makes it a little confusing as to the height range of this cart and its bigger brother but looking at the manuals I don't think either reaches my planer bed, which is just over 35". My HD table is scheduled to arrive tomorrow. Menards has the Bosch Powered Hand Planer on sale and I picked one up as it looks like it has some nice upgrades from my flea market find: dust collection, power switch on/off locking, and a stand for setting it down before it tops spinning. I'll report back on it. 2 Quote
Popular Post Von Posted July 24 Author Popular Post Report Posted July 24 Onto board two with a couple new tools. First was the new Bosch powered hand planer. I'm not going to do a full review, but in brief: Pros: It has dust collection, a lot more power, and it's a lot smoother to use. I only barely used my scrub plane flattening my board and probably could have done without it if I tried. Con #1: It's hard to blame the tool for this, but the shaving it puts out clogged my dust collection over and over again. They are strands that seem to bind together with the slightest provocation. I had to stop and unclog the dust collection four or five times. Granted I'm using an expansion hose whose ridges may be adding to the problem. Con #2: It has a plastic doohickey you can use to shift the dust collection from one side to the other, which was very useful as my hose was centered in my board and I could switch half way through and keep the hose out of the way. That is until about the third time I shifted it and the wimpy plastic handle broke. So much for that feature. That said, the planer worked well and I got my board "flat enough" and then got to use my new Husky adjustable table to move it around for thickness planing. Thank you for the recommendation - this thing is great in that I never had to lift the board during the whole planing process. My only minor gripe is the raising mechanism is very squeaky. I did some reading online and sounds like some dry lube on the legs is suggested. Second board surfaced on the two flats. It fits well to the first with a little bow I think I'll be able to clamp out. I hope to finish the last two this weekend. 3 Quote
Popular Post Von Posted July 25 Author Popular Post Report Posted July 25 No photos - same old same old. Got the third board planed. I've given up on dust collection for the hand planer, it just clogs too readily. I spent some extra time with the hand planer trying to reduce the number of cycles through the thickness planer but don't know I achieved anything. I have a hard time judging setting the depth of my first pass on the thickness planer and always seem go too very conservative and I spend the first 3-4 passes sneaking up, in 1/32" increments, to the point I'm doing real work. 3 Quote
Popular Post gee-dub Posted July 25 Popular Post Report Posted July 25 On 7/25/2026 at 10:34 AM, Von said: I have a hard time judging setting the depth of my first pass on the thickness planer The DRO. Don't start planing without it 3 1 Quote
Popular Post Von Posted July 26 Author Popular Post Report Posted July 26 13 hours ago, gee-dub said: The DRO. Don't start planing without it Agreed and I have a DRO. For once, lack of precision is not my problem :-) Mainly I think I need more experience looking at a board and guestimating how much I can plane in my first pass, but I welcome any heuristics folks have developed. My challenge is with my DeWalt on a board this wide (11") if I try to take a deep enough bite, I will trip its breaker, which is a PITA to recover from, so I try to go gentle. E.g. once I get to the point I'm planing most of the board, I will only turn the depth wheel about 1/4 turn between passes (1/64"). I suspect that's a little conservative, but gets me a clean cut without risking tripping the breaker. The challenge is what height to start at with a board this rough? I'm not planning nearly the whole board with my first passes to start so I can be more aggressive. And for my first pass, it feels like a crap shoot. I poke around the board with my height gauge and find the high spot (since I've got the cup up, it's on the edge). But that high spot is just that and setting my planer to it means I will probably only touch the board in a couple of spots, almost certainty not enough for the rollers to get a grip on the board and I'm manually pushing it through. So I'm trying to learn to eyeball the board and guess how far down from the high spot I should start so I don't spend my first 3-4 passes mostly planing air and feeling like I'm doing some sort of bizarre exercise routine moving lumber around my shop. Right now I'm going down about a half turn (~1/32") and thats often not enough to even consistently engage the rollers so I have room to be more aggressive. 4 Quote
Popular Post wtnhighlander Posted July 26 Popular Post Report Posted July 26 @Von, I have the 735 also. My general process for milling from rough-sawn is to find the thickest board of the batch, and feed it in (with power off and head raised) to the highest spot, then lower the head until the depth gauge bar touches wood and indicates no more than 1/32" depth. Count turns while opening the head, remove the board, and return the head to the indicated position. By the time the thinnest board has been surfaced, all the thicknesses will be equal, even though that means some passes cut nothing but air, in the beginning. I feel your pain about the breaker. On a 20A circuit, if I leave my planer running to long, even without cutting, the machine's thermal breaker will trip. Sometimes even the upstream panel breaker will trip, on a hot day. This annoyance has caused me to rely much more on hand-held tools for much of my material prep. If you ever have the opportunity to ditch the 735 and its universal motor, in favor of a floor-standing planer with an induction motor, take it. 5 Quote
gee-dub Posted July 26 Report Posted July 26 I may have answered prematurely. As wtnhighlander says, find the thickest part of the board. I use a caliper and have one stuck to the top of my planer. If the thickest part of my board is 1-15/16" I set the planer at 1-7/8" and take the first pass assuming I have a decent reference surface. I probably say this too often but a planer sled can save you a lot of work as long as the stock isn't longer than the sled. Mine is 60" long as I find that this meets most needs for furniture. If you don't plan for the bench to be that long, cut the boards to rough length. This will reduce the impact of any irregularities. 2 Quote
Popular Post Von Posted July 27 Author Popular Post Report Posted July 27 First, a big thank you to @Beechwood Chip - the planer blades you sent me came in very handy today. BTW, has anyone had luck sharpening the DeWalt 735 planer blades? Given their price (e.g. $90 for 6 knives at Lowes), I'm leaning towards it not being worth the effort. @wtnhighlander @gee-dub Thanks for the advice. I agree with everything you say, but somehow I found myself doing a lot of very light passes to get the planer to the meat of the work. I suspect my high spots were bigger outliers and I just needed to be braver in taking big first passes. I finished planing my fourth and last board for my top today. They are all within about 1/16" of 1 7/8" thick, but I do have a thicker and a thinner one, so I'm going to pair those up and then pair up the two in the middle to try to minimize work getting them co-planar. Here's a pair I put together to get an idea of how much clamping I was going to need to do and I'm pleasantly surprised there isn't much of a gap (there is a deceptive shadow line in the photo as the top board is overhanging the bottom). I don't know I can get the glue line to disappear. I might hide it with an inlay if I'm not happy with the look. I have a couple more deep throat clamps ordered. Tomorrow I'll try a dry run clamping and may go for it if I think I have enough clamps. 5 Quote
Popular Post wtnhighlander Posted July 27 Popular Post Report Posted July 27 As I recall, the Dewalt knives have index holes that align over pins / nubs on the cutter head. This means no adjustment for knife wear, so you can't take much off for honing, and if the resulting edge isn't parallel to the pins, no way to align it to the work. I'd stick to light, careful honong. 4 Quote
Ron Swanson Jr. Posted July 27 Report Posted July 27 On 7/26/2026 at 7:53 AM, Von said: Agreed and I have a DRO. For once, lack of precision is not my problem :-) Mainly I think I need more experience looking at a board and guestimating how much I can plane in my first pass, but I welcome any heuristics folks have developed. My challenge is with my DeWalt on a board this wide (11") if I try to take a deep enough bite, I will trip its breaker, which is a PITA to recover from, so I try to go gentle. E.g. once I get to the point I'm planing most of the board, I will only turn the depth wheel about 1/4 turn between passes (1/64"). I suspect that's a little conservative, but gets me a clean cut without risking tripping the breaker. The challenge is what height to start at with a board this rough? I'm not planning nearly the whole board with my first passes to start so I can be more aggressive. And for my first pass, it feels like a crap shoot. I poke around the board with my height gauge and find the high spot (since I've got the cup up, it's on the edge). But that high spot is just that and setting my planer to it means I will probably only touch the board in a couple of spots, almost certainty not enough for the rollers to get a grip on the board and I'm manually pushing it through. So I'm trying to learn to eyeball the board and guess how far down from the high spot I should start so I don't spend my first 3-4 passes mostly planing air and feeling like I'm doing some sort of bizarre exercise routine moving lumber around my shop. Right now I'm going down about a half turn (~1/32") and thats often not enough to even consistently engage the rollers so I have room to be more aggressive. I'll throw in my $.02, not because I have much to offer that hasn't already been said, but because I'm bored at work. I have a 735 also and my process is pretty much what you're describing. I crank down until just barely making contact with the highest spots and the first few passes don't take much off an usually i have to help the rollers pull the piece through. This is no different than using hand planes. The high spots need to come off first and it's a little anticlimactic when they do. Not much seems to be happening at first. I have to remind myself to be patient and the flatter it gets, the more material will come off with each stroke of the plane or pass through the planer. Planing massive boards like you've got only exasperates the situation as they're unwieldy to feed and a lot tougher to gauge the high spots. The other thing is that, strategically, I try to do as little planing as possible in the first place - mainly by buying stock that's close to my finished size and resawing the bulk of waste away when possible. Anyway, like I said, just killing some down time. You're progressing nicely through this build and it's a good one to follow along with. 2 Quote
Popular Post Beechwood Chip Posted July 27 Popular Post Report Posted July 27 On 7/26/2026 at 10:24 PM, Beechwood Chip said: I took them to a general "fix-it" guy out in farm country who sharpened them for me. It doesn't need to be a Certified DeWalt Service Technician. I think I was remembering my jointer knives and not the planer knives. If they have index holes, they probably can't be sharpened. 3 Quote
Ron Swanson Jr. Posted July 27 Report Posted July 27 On 7/27/2026 at 5:43 AM, wtnhighlander said: As I recall, the Dewalt knives have index holes that align over pins / nubs on the cutter head. This means no adjustment for knife wear, so you can't take much off for honing, and if the resulting edge isn't parallel to the pins, no way to align it to the work. I'd stick to light, careful honong. About 20 years ago I ordered carbide knives for my planer from infinity. They did stay sharp for a lot longer than steel, but eventually they got dull and when I asked about getting them sharpened, that is exactly what they said. You can do some light honing, but that's about it. 2 Quote
Popular Post Chestnut Posted July 27 Popular Post Report Posted July 27 To get started I usually start with the cutter head high and feed the thickest board in. With the machine on I'll adjust the depth of cut until the cutter head starts cutting. Then i crank down 1/2 to 1_1/2 turn to start removing to my goal. I do miss the depth of cut gauge on the in-feed of the dewalt. It really helped me know when I'm in the ballpark. Sometimes I'll process boards individually to get them all cleaned. Then it's a quick measurement and add the boards in as the planer setting reaches their thickness. Helps reduce moving heavy lumber to just cut air. The short life of the steel knives and the noise on the 735 pushed me to a helical head pretty quick. I know the conventional wisdom is carbide takes more power than steel but i swear with the 735 it was the opposite. I could easily do a half to 3/4 turn IIRC with the helical head on a 6" wide board. In the end i upgraded to stationary. It's a bit crazy to think that the dewalt is tripping a 20 amp (2,400 watt) breaker removing 1/32" where my planer draws 12 amp (2,880 watt) removing 1/8" on a 6" wide board. I measured it because i was curious. 7 Quote
Popular Post Von Posted July 29 Author Popular Post Report Posted July 29 Dry run for the glue up. Q for the collective group: With as much surface area, how long should I allow the glue to set before considering it cured? I'm using Titebond original. Overnight enough or will it need longer? I've got two more of the deep throat clamps (in the middle) arriving today so holding off until tomorrow to do the real thing. In terms of flatness, looks like I'm about 1/16" off in one spot. Best as I can tell, it was a little bow in a board that caused it to plane a little thinner. I shifted it on my bench and trying adjusting my clamps with only a little improvement. I'm not going to chase this further now. I have a long way to go before I get both tops on the bench and really worry about flatness. I'm right around 3 3/4" total thickness btw. 4 Quote
Ron Swanson Jr. Posted July 29 Report Posted July 29 Overnight should be fine. If there's one thing I'm compelled to mention on the subject, it's that a THIN SPREAD of glue will do the job. Especially with something this size, if you go too heavy it'll squeeze out all over the place and you'll be up to your eyeballs in Titebond. 2 Quote
Mark J Posted July 30 Report Posted July 30 21 hours ago, Von said: got two more of the deep throat clamps (in the middle) arriving today What clamps did you get? Quote
Popular Post Von Posted July 30 Author Popular Post Report Posted July 30 Glue up. I realized last night I was somehow going to have to lift one board, flip it over and put it on the other while both were buttered with glue. Given I would have a hard time doing this without the glue involved, I needed a plan. I ended up making a temporary 2x stand for the top board (on the right in the photo below) so it would be higher than then lower board and gravity would be on my side. This worked well, I buttered both and then flipped the top board first onto its side and then over onto the bottom without having to actually lift it. Lesson 1: Spreading glue on these things is like painting a wall, it feels like it takes forever. A big problem was my glue spreader, photo below, which was way too small for this job. My hand was cramping holding it by the time I was done. For the other half of the top, I'm going to look for some sort of drywall mud spreader. Lesson 2: It was no problem aligning the boards in the dry run, friction was my friend, but with the glue between them, the boards went back and forth between sliding freely and sticking seemingly at random. I was chasing my tail trying to get them to align as they would keep finding new pivot points - I'd line up one end and the other end would have shifted 2 inches while my back was turned. Finally I got smarter and put a couple parallel clamps across them to get and keep them lined up. Obligatory clamp porn photo: 20 minutes ago, Mark J said: What clamps did you get? Bessey TG 16 in. Bar Clamps with 7 in. Throat Depth. I already had a pair so knew they did a good job of reaching the middle of my boards. Edited to add: Thanks @Ron Swanson Jr. and @wtnhighlander for glue-up time guidance. Looking at my schedule I won't get back to this until tomorrow afternoon which sounds like it should work well. 4 Quote
Popular Post gee-dub Posted July 30 Popular Post Report Posted July 30 Nicely done. When we work alone we have to be a little inventive when it comes to heavy or awkward items. There have been times I have had to just wait till I could get someone to help but I suck at waiting 3 Quote
Ron Swanson Jr. Posted July 30 Report Posted July 30 On 7/30/2026 at 8:51 AM, Von said: Glue up. I realized last night I was somehow going to have to lift one board, flip it over and put it on the other while both were buttered with glue. Given I would have a hard time doing this without the glue involved, I needed a plan. I ended up making a temporary 2x stand for the top board (on the right in the photo below) so it would be higher than then lower board and gravity would be on my side. This worked well, I buttered both and then flipped the top board first onto its side and then over onto the bottom without having to actually lift it. Lesson 1: Spreading glue on these things is like painting a wall, it feels like it takes forever. A big problem was my glue spreader, photo below, which was way too small for this job. My hand was cramping holding it by the time I was done. For the other half of the top, I'm going to look for some sort of drywall mud spreader. Lesson 2: It was no problem aligning the boards in the dry run, friction was my friend, but with the glue between them, the boards went back and forth between sliding freely and sticking seemingly at random. I was chasing my tail trying to get them to align as they would keep finding new pivot points - I'd line up one end and the other end would have shifted 2 inches while my back was turned. Finally I got smarter and put a couple parallel clamps across them to get and keep them lined up. Obligatory clamp porn photo: Bessey TG 16 in. Bar Clamps with 7 in. Throat Depth. I already had a pair so knew they did a good job of reaching the middle of my boards. Edited to add: Thanks @Ron Swanson Jr. and @wtnhighlander for glue-up time guidance. Looking at my schedule I won't get back to this until tomorrow afternoon which sounds like it should work well. @von try rolling it on with a short 4"(?) Paint roller. That's what I used and it worked great. 1 Quote
fcschoenthal Posted July 30 Report Posted July 30 On 7/30/2026 at 11:57 AM, Ron Swanson Jr. said: @von try rolling it on with a short 4"(?) Paint roller. That's what I used and it worked great. I was about to suggest the same thing when reading through his post. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.