Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Question about cabinet doors

Featured Replies

I hearby request input from the collective minds!

Shop organization demands that I build several cabinets to hide my clutter and repel the dust I can't seem to collect. Contents require 12" interior height, 10" interior depth. Location allows units of 36" exterior width, and I plan to make several to maximize efficiency.

The question concerns the doors. I work in a tight space, where typical side-swing doors will be awkward to deal with. I need a door design that minimizes the space occupied outside the cabinet when it is open, but also seals well enough to keep most of the dust out when closed. Cost is a key factor, so fancy hardware is contra-indicated.

My thoughts so far include sliding panels, but only half the cabinet opens at once, and tracks get clogged. Tambour opens fully, but requires more interior space and tracks still clog. Barrister book case doors seem the simplest, but still need room to swing open before sliding back.

Anyone have ideas?

I'm picturing a situation where you have to stand right in front of the cabinets, so there's no room to swing a door outwards.  Is that correct?

Do you have space above, below, or to the sides of the cabinets?  As you said, the doors have to go somewhere.

  • Popular Post

How about bi-fold doors?  I've seen these where, unlike closet doors, the door's leading edge does not ride in a track.  So when closed the door lays against the frame, but when released from the catch (a magnet?) the door opens away from the cabinet and can fold in two.  Your 36" cabinet would have two 18" doors, and each of these would have two 9" folding panels.

  • Author
9 hours ago, Beechwood Chip said:

I'm picturing a situation where you have to stand right in front of the cabinets, so there's no room to swing a door outwards.  Is that correct?

Do you have space above, below, or to the sides of the cabinets?  As you said, the doors have to go somewhere.

Exactly. I need to hang several of these boxes, some of which have room enough for common side-swing doors, but some do not. I'm looking for a compromise that works in either case, so I can batch out everything at once.

  • Author
9 hours ago, Mark J said:

How about bi-fold doors?  I've seen these where, unlike closet doors, the door's leading edge does not ride in a track.  So when closed the door lays against the frame, but when released from the catch (a magnet?) the door opens away from the cabinet and can fold in two.  Your 36" cabinet would have two 18" doors, and each of these would have two 9" folding panels.

Good thought! I recall seeing an article about something similar, only they were called sometbing else, 'accordion' maybe? Wonder how many 'leaves' each door could be broken down to, without becoming too floppy to work?

  • Popular Post

Googled space saving cabinet doors and found this about bi-fold doors. 

 

  • Popular Post

Does the width need to be 36"? If your making multiple can you play with 3 and separate the cabinets in to 18" units? Instead of making a tri or quad fold door just maker more units? Number of hinges are going to be the same you'll just have more dividers.

Silly question. Does the door NEED to be solid? Could you do a canvas or fabric roll up door with elastic buckles to hold them in place. It might take some different construction methods but grommets are cheap and easy to install and fabric can be pretty inexpensive. have the elastic pull the fabric so it overlays tight on the face frame and it should seal dust well unless your hitting them with a leaf blower.

If you really needed to seal them to blow out your shop with a blower you could make cauls that screw over the edges of the fabric to hold it down tight.

  • Author
  • Popular Post

Fabric is an interesting option, thanks for bringing that up, Drew!

I want to stay with units 36" wide because that fits between the shop wall and the edge of my "tool board" on both sides. More 36" units nestle nicely into other available wall spaces, and retain max capacity per unit. Making a single form factor maximizes construction efficiency.

The "least hardware" approach seems to be the simple "Barrister Bookcase" style, using just pins in a groove, rather than rollers. Now you have triggered the idea of that type door, made with frame & panel, but the panel is canvas, and the vertical stiles have horizontal kerfs so they can flex in one direction, like a tambour, and sort of roll up into the case top without swinging forward. Hhhmmm.... I feel a prototype beginning to develop!

 

Ross , I made the WoodWhisper’s Barristers Bookcase project several years ago. It does limit you to the height of storage inside the cabinet as the door is stored there. It also seems that fabric, although a good idea, would tend to collect dust more than a smooth wood surface. 

10 hours ago, Coop said:

It also seems that fabric, although a good idea, would tend to collect dust more than a smooth wood surface. 

I was thinking if i wanted to spin this as a feature of passive dust collection :D. Yes you are right though. Though ever surface is going to collect dust even the plywood walls in my shop collect dust.

  • 4 months later...
  • Author
  • Popular Post

So, I threw together a prototype, from assorted scraps. The size works, and a barrister-style door works within the space, but doesn't work smoothly in my hastily built test box. Moving forward, I have started batching out frame parts.

IMG_20250708_044604012.thumb.jpg.b5eef0569e9a5f356a32b5cbaeb3aec6.jpg

I cut bridles on the short stiles, with my shop made tenon jig. It holds the part vertical and rides the rip fence, but my design has a pretty narrow footprint. This is allowing it to shift out of square to the table, so I switched to nibbling out the tenons with my dado stack. It is more precise in position, but leaves a rougher cut, which required some clean up with a router plane.

IMG_20250708_053735096.thumb.jpg.6fe086e2bc4dea001657a6c38342e78b.jpg

All I had time for today. Material is paulownia, and the panels will be masonite / tempered hardboard, I think. Should keep the weight down.

Still a possibility of switching to bi- or tri-fold, side-hinged doors, at least for some locations.

  • 2 weeks later...
  • Author
  • Popular Post

Wow, shop sessions have been brief, few, and far between during this project. Some progress, though. Bridle joints turn sticks into panel frames. Tongue & groove joints assemble panel frames into box frames.

IMG_20250717_053336164.thumb.jpg.706000b98e627093cf41b83a1aae379c.jpg

Having stock sized to a multiple of blade thicknesses from my dado stack made adjusting the stack to cut a 50% tongue easy. Setting the fence to one full board thickness away from the far side of the dado stack places the grooves 50% in from the edge. Grooves are cut using the miter gauge and guided by the fence. Not a through-cut, so no projectiles to kick back. 

This is my field-expedient "tenon jig" to hold the tongue cuts from dropping into the open throat of the saw.

IMG_20250717_053133541.thumb.jpg.8a695f1295f41735c7859866062d48dd.jpg

Stack was a hair to wide to use the throat plate.

On 7/17/2025 at 11:17 AM, BillyJack said:

Why do you need doors?

On 3/4/2025 at 6:05 AM, wtnhighlander said:

Shop organization demands that I build several cabinets to hide my clutter and repel the dust I can't seem to collect. 

I certainly can understand both needs.

When building cabinets I created a lot of dust, but making furniture I don’t.

 

When I finish building my cabinets, I blow the dust off everything with the DC and over head DC doesn’t catch..

  • Author
  • Popular Post

Between 6:00 and 7:30 am, I sprayed a gallon of grass killer, string-trimmed 400 ft of ditch, loaded trash to take to the dump, and finished the joinery for my storage box frames.

IMG_20250719_073100867.thumb.jpg.cfe1c6864e59bfb9533cd67a9ead208f.jpg

By the time that was done, I was completely soaked with sweat, and ready to be done for the day. 

Temperature is still just in the upper 70s, but humidity is 96%. By the end of the shop session, I was  wiping sweat off the table saw more than I was cutting wood!

On 7/19/2025 at 5:44 AM, wtnhighlander said:

I was  wiping sweat off the table saw more than I was cutting wood!

When I start dripping sweat on the project or tools I just call it a day. :huh:

On 7/19/2025 at 12:12 PM, Chet said:

When I start dripping sweat on the project or tools I just call it a day. :huh:

Yep. I sweat easily. I can work in heat. I can't work in a swimming pool.

Completely different. No doors. A shower curtain with magnets glued on. And a beveled cornice to control dust getting in near the curtain rings. It won't be crafty but I think it will do the job.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.